[OpenWrt-Devel] [PATCHv2] ramips: add support for Planex CS-QR10

YuheiOKAWA tochiro.srchack at gmail.com
Fri Apr 22 05:44:44 EDT 2016


CS-QR10 is MT7620A based IP Camera.

the camera and sound does not work with kernel 4.4.
 - camera chip is sn9c291.
 - sound chip is wm8960.

Signed-off-by: YuheiOKAWA <tochiro.srchack at gmail.com>
---
 target/linux/ramips/base-files/etc/board.d/01_leds |   3 +-
 .../linux/ramips/base-files/etc/board.d/02_network |   1 +
 target/linux/ramips/base-files/etc/diag.sh         |   1 +
 target/linux/ramips/base-files/lib/ramips.sh       |   3 +
 .../ramips/base-files/lib/upgrade/platform.sh      |   1 +
 target/linux/ramips/dts/CS-QR10.dts                | 163 +++++++++++++++++++++
 target/linux/ramips/image/mt7620.mk                |   2 +
 target/linux/ramips/mt7620/profiles/planex.mk      |  14 ++
 8 files changed, 187 insertions(+), 1 deletion(-)
 create mode 100644 target/linux/ramips/dts/CS-QR10.dts

diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
index e3b8500..367801d 100755
--- a/target/linux/ramips/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/base-files/etc/board.d/01_leds
@@ -30,7 +30,8 @@ br-6475nd|\
 mzk-w300nh2)
 	set_wifi_led "$board:amber:wlan"
 	;;
-a5-v11)
+a5-v11|\
+cs-qr10)
 	ucidef_set_led_default "power" "POWER" "$board:red:power" "1"
 	;;
 ai-br100)
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index 3c958ae..dc3d1bc 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -160,6 +160,7 @@ ramips_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "9 at eth0"
 		;;
+	cs-qr10|\
 	d105|\
 	hpm|\
 	na930|\
diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh
index bd0ff05..2d43f54 100644
--- a/target/linux/ramips/base-files/etc/diag.sh
+++ b/target/linux/ramips/base-files/etc/diag.sh
@@ -33,6 +33,7 @@ get_status_led() {
 		status_led="$board:green:power"
 		;;
 	a5-v11|\
+	cs-qr10|\
 	d105|\
 	dcs-930l-b1|\
 	ex2700|\
diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
index 550ec55..73dd599 100755
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -88,6 +88,9 @@ ramips_board_detect() {
 	*"CF-WR800N")
 		name="cf-wr800n"
 		;;
+	*"CS-QR10")
+		name="cs-qr10"
+		;;
 	*"CY-SWR1100")
 		name="cy-swr1100"
 		;;
diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index 73ba6e6..f153b02 100755
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -34,6 +34,7 @@ platform_check_image() {
 	broadway|\
 	carambola|\
 	cf-wr800n|\
+	cs-qr10|\
 	d105|\
 	dap-1350|\
 	db-wrt01|\
diff --git a/target/linux/ramips/dts/CS-QR10.dts b/target/linux/ramips/dts/CS-QR10.dts
new file mode 100644
index 0000000..08299e3
--- /dev/null
+++ b/target/linux/ramips/dts/CS-QR10.dts
@@ -0,0 +1,163 @@
+/dts-v1/;
+
+/include/ "mt7620a.dtsi"
+
+/ {
+	compatible = "ralink,mt7620a-soc";
+	model = "Planex CS-QR10";
+
+	palmbus at 10000000 {
+		gpio0: gpio at 600 {
+			status = "okay";
+		};
+
+		gpio1: gpio at 638 {
+			status = "okay";
+		};
+
+		gpio2: gpio at 660 {
+			status = "okay";
+		};
+
+		gpio3: gpio at 688 {
+			status = "okay";
+		};
+
+		i2c at 900 {
+			status = "okay";
+		};
+
+		i2s: i2s at a00 {
+			status = "okay";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pcm_i2s_pins>;
+		};
+
+		spi at b00 {
+			status = "okay";
+
+			m25p80 at 0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "jedec,spi-nor";
+				reg = <0 0>;
+				linux,modalias = "m25p80", "mx25l6405d";
+				spi-max-frequency = <10000000>;
+
+				partition at 0 {
+					label = "u-boot";
+					reg = <0x0 0x30000>;
+					read-only;
+				};
+
+				partition at 30000 {
+					label = "u-boot-env";
+					reg = <0x30000 0x10000>;
+					read-only;
+				};
+
+				factory: partition at 40000 {
+					label = "factory";
+					reg = <0x40000 0x10000>;
+					read-only;
+				};
+
+				partition at 50000 {
+					label = "firmware";
+					reg = <0x50000 0x7b0000>;
+				};
+			};
+		};
+
+		pcm at 2000 {
+			status = "okay";
+		};
+
+		gdma at 2800 {
+			status = "okay";
+		};
+	};
+
+	pinctrl {
+		state_default: pinctrl0 {
+			gpio {
+				ralink,group = "spi refclk", "rgmii1";
+				ralink,function = "gpio";
+			};
+			wdt {
+				ralink,group = "wdt";
+				ralink,function = "wdt refclk";
+			};
+		};
+	};
+
+	ethernet at 10100000 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&ephy_pins>;
+		mtd-mac-address = <&factory 0x4>;
+		mediatek,portmap = "llllw";
+	};
+
+	gsw at 10110000 {
+		ralink,port4 = "ephy";
+	};
+
+	sdhci at 10130000 {
+		status = "okay";
+	};
+
+	ehci at 101c0000 {
+		status = "okay";
+	};
+
+	ohci at 101c1000 {
+		status = "okay";
+	};
+
+	wmac at 10180000 {
+		ralink,mtd-eeprom = <&factory 0>;
+	};
+
+	pcie at 10140000 {
+		status = "okay";
+	};
+
+	sound {
+		compatible = "mediatek,mt7620-audio-wm8960";
+		model = "mt7620-wm8960";
+		i2s-controller = <&i2s>;
+		audio-routing =
+		"Ext Spk", "SPK_LP",
+ 		"Ext Spk", "SPK_LN",
+		"Ext Spk", "SPK_RP",
+ 		"Ext Spk", "SPK_RN";
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		power {
+			label = "cs-qr10:red:power";
+			gpios = <&gpio1 4 1>;
+		};
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <20>;
+
+		s1 {
+			label = "reset";
+			gpios = <&gpio1 1 1>;
+			linux,code = <0x198>;
+		};
+
+		s2 {
+			label = "wps";
+			gpios = <&gpio1 3 1>;
+			linux,code = <0x211>;
+		};
+	};
+};
diff --git a/target/linux/ramips/image/mt7620.mk b/target/linux/ramips/image/mt7620.mk
index c76e98e..d742151 100644
--- a/target/linux/ramips/image/mt7620.mk
+++ b/target/linux/ramips/image/mt7620.mk
@@ -95,6 +95,7 @@ whr_1166d_mtd_size=15400960
 Image/Build/Profile/WHR1166D=$(call BuildFirmware/CustomFlash/$(1),$(1),whr-1166d,WHR-1166D,$(whr_1166d_mtd_size))
 dlink810l_mtd_size=6881280
 Image/Build/Profile/CF-WR800N=$(call BuildFirmware/Default8M/$(1),$(1),cf-wr800n,CF-WR800N)
+Image/Build/Profile/CS-QR10=$(call BuildFirmware/Default8M/$(1),$(1),cs-qr10,CS-QR10)
 Image/Build/Profile/DIR-810L=$(call BuildFirmware/CustomFlash/$(1),$(1),dir-810l,DIR-810L,$(dlink810l_mtd_size))
 na930_mtd_size=20971520
 Image/Build/Profile/NA930=$(call BuildFirmware/CustomFlash/$(1),$(1),na930,NA930,$(na930_mtd_size))
@@ -138,6 +139,7 @@ define Image/Build/Profile/Default
 	$(call Image/Build/Profile/MT7620a_V22SG,$(1))
 	$(call Image/Build/Profile/AI-BR100,$(1))
 	$(call Image/Build/Profile/CF-WR800N,$(1))
+	$(call Image/Build/Profile/CS-QR10,$(1))
 	$(call Image/Build/Profile/RP-N53,$(1))
 	$(call Image/Build/Profile/DIR-810L,$(1))
 	$(call Image/Build/Profile/WHR300HP2,$(1))
diff --git a/target/linux/ramips/mt7620/profiles/planex.mk b/target/linux/ramips/mt7620/profiles/planex.mk
index f6f2cf1..15560ab 100644
--- a/target/linux/ramips/mt7620/profiles/planex.mk
+++ b/target/linux/ramips/mt7620/profiles/planex.mk
@@ -5,6 +5,20 @@
 # See /LICENSE for more information.
 #
 
+define Profile/CS-QR10
+	NAME:=Planex CS-QR10
+	PACKAGES:=\
+		kmod-usb-core kmod-usb2 kmod-usb-ohci \
+		i2c-core kmod-i2c-ralink kmod-sound-core kmod-sound-mtk \
+		kmod-sdhci-mt7620
+endef
+
+define Profile/CS-QR10/Description
+	Package set optimized for the Planex CS-QR10.
+endef
+$(eval $(call Profile,CS-QR10))
+
+
 define Profile/MZK-750DHP
 	NAME:=Planex MZK-750DHP
 	PACKAGES:= kmod-mt76 kmod-mt7610e
-- 
1.9.1
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel


More information about the openwrt-devel mailing list