[OpenWrt-Devel] [PATCH v5 5/5] ar71xx: add support for Cisco's MR18

Chris R Blake chunkeey at googlemail.com
Tue Sep 22 13:08:13 EDT 2015


From: Chris R Blake <chrisrblake93 at gmail.com>

This patch adds support for Cisco's MR18.
Detailed instructions for the flashing the device can
be found in the OpenWrt forum thread:
<https://forum.openwrt.org/viewtopic.php?id=59248>

Signed-off-by: Chris R Blake <chrisrblake93 at gmail.com>
---
 package/base-files/files/lib/functions/system.sh   |  17 ++
 target/linux/ar71xx/base-files/etc/diag.sh         |   3 +
 .../etc/hotplug.d/firmware/10-ath9k-eeprom         |  38 ++-
 .../ar71xx/base-files/etc/uci-defaults/01_leds     |   4 +
 .../ar71xx/base-files/etc/uci-defaults/02_network  |   1 +
 target/linux/ar71xx/base-files/lib/ar71xx.sh       |   3 +
 .../base-files/lib/preinit/05_set_iface_mac_ar71xx |   4 +
 .../ar71xx/base-files/lib/upgrade/merakinand.sh    | 137 +++++++++++
 .../ar71xx/base-files/lib/upgrade/platform.sh      |   7 +
 target/linux/ar71xx/config-4.1                     |   1 +
 .../linux/ar71xx/files/arch/mips/ath79/mach-mr18.c | 254 +++++++++++++++++++++
 target/linux/ar71xx/image/Makefile                 |  34 +++
 target/linux/ar71xx/nand/config-default            |   1 +
 target/linux/ar71xx/nand/profiles/meraki.mk        |  17 ++
 .../817-MIPS-ath79-add-meraki-mr18-support.patch   |  41 ++++
 15 files changed, 561 insertions(+), 1 deletion(-)
 create mode 100644 target/linux/ar71xx/base-files/lib/upgrade/merakinand.sh
 create mode 100644 target/linux/ar71xx/files/arch/mips/ath79/mach-mr18.c
 create mode 100644 target/linux/ar71xx/nand/profiles/meraki.mk
 create mode 100644 target/linux/ar71xx/patches-4.1/817-MIPS-ath79-add-meraki-mr18-support.patch

diff --git a/package/base-files/files/lib/functions/system.sh b/package/base-files/files/lib/functions/system.sh
index 8d75a5a..928a429 100644
--- a/package/base-files/files/lib/functions/system.sh
+++ b/package/base-files/files/lib/functions/system.sh
@@ -41,6 +41,23 @@ mtd_get_mac_binary() {
 	dd bs=1 skip=$offset count=6 if=$part 2>/dev/null | hexdump -v -n 6 -e '5/1 "%02x:" 1/1 "%02x"'
 }
 
+mtd_get_mac_binary_ubi() {
+	local mtdname="$1"
+	local offset="$2"
+
+	. /lib/upgrade/nand.sh
+
+	local ubidev=$( nand_find_ubi $CI_UBIPART )
+	local part="$( nand_find_volume $ubidev $1 )"
+
+	if [ -z "$part" ]; then
+		echo "mtd_get_mac_binary: ubi partition $mtdname not found!" >&2
+		return
+	fi
+
+	dd bs=1 skip=$offset count=6 if=/dev/$part 2>/dev/null | hexdump -v -n 6 -e '5/1 "%02x:" 1/1 "%02x"'
+}
+
 mtd_get_part_size() {
 	local part_name=$1
 	local first dev size erasesize name
diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh
index cfba6b4..d6cc23f 100644
--- a/target/linux/ar71xx/base-files/etc/diag.sh
+++ b/target/linux/ar71xx/base-files/etc/diag.sh
@@ -144,6 +144,9 @@ get_status_led() {
 	mr16)
 		status_led="mr16:green:power"
 		;;
+	mr18)
+		status_led="mr18:green:tricolor0"
+		;;
 	mr600)
 		status_led="mr600:orange:power"
 		;;
diff --git a/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
index b5f0588..bfab8bb 100644
--- a/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
+++ b/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
@@ -9,11 +9,14 @@ ath9k_eeprom_extract() {
 	local part=$1
 	local offset=$2
 	local count=$3
+	local ubidev=$( nand_find_ubi $CI_UBIPART )
 	local mtd
 
 	mtd=$(find_mtd_chardev $part)
 	[ -n "$mtd" ] || \
-		ath9k_eeprom_die "no mtd device found for partition $part"
+		mtd="/dev/$(nand_find_volume $ubidev $part)"
+		[ -n "$mtd" ] || \
+			ath9k_eeprom_die "no mtd device found for partition $part"
 
 	dd if=$mtd of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
 		ath9k_eeprom_die "failed to extract from $mtd"
@@ -32,12 +35,21 @@ ath9k_patch_firmware_mac() {
 . /lib/ar71xx.sh
 . /lib/functions.sh
 . /lib/functions/system.sh
+. /lib/upgrade/nand.sh
 
 board=$(ar71xx_board_name)
 
 case "$FIRMWARE" in
 "soc_wmac.eeprom")
 	case $board in
+	mr18)
+		if [ -n "$(nand_find_volume ubi0 caldata)" ]; then
+			ath9k_eeprom_extract "caldata" 4096 2048
+		else
+			ath9k_eeprom_extract "odm-caldata" 4096 2048
+		fi
+		ath9k_patch_firmware_mac $(macaddr_add $(mtd_get_mac_binary_ubi board-config 102) +1)
+		;;
 	r6100 | \
 	wndr3700v4 | \
 	wndr4300)
@@ -52,6 +64,14 @@ case "$FIRMWARE" in
 
 "pci_wmac0.eeprom")
 	case $board in
+	mr18)
+		if [ -n "$(nand_find_volume ubi0 caldata)" ]; then
+			ath9k_eeprom_extract "caldata" 20480 2048
+		else
+			ath9k_eeprom_extract "odm-caldata" 20480 2048
+		fi
+		ath9k_patch_firmware_mac $(macaddr_add $(mtd_get_mac_binary_ubi board-config 102) +2)
+		;;
 	wndr3700v4 | \
 	wndr4300)
 		ath9k_eeprom_extract "caldata" 20480 2048
@@ -62,4 +82,20 @@ case "$FIRMWARE" in
 		;;
 	esac
 	;;
+
+"pci_wmac1.eeprom")
+	case $board in
+	mr18)
+		if [ -n "$(nand_find_volume ubi0 caldata)" ]; then
+			ath9k_eeprom_extract "caldata" 36864 2048
+		else
+			ath9k_eeprom_extract "odm-caldata" 36864 2048
+		fi
+		ath9k_patch_firmware_mac $(macaddr_add $(mtd_get_mac_binary_ubi board-config 102) +3)
+		;;
+	*)
+		ath9k_eeprom_die "board $board is not supported yet"
+		;;
+	esac
+	;;
 esac
diff --git a/target/linux/ar71xx/base-files/etc/uci-defaults/01_leds b/target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
index fac4751..dcf4aa5 100644
--- a/target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
+++ b/target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
@@ -260,6 +260,10 @@ mr16)
 	ucidef_set_led_wlan "wlan4" "WLAN4" "mr16:green:wifi4" "phy0tpt"
 	;;
 
+mr18)
+	ucidef_set_led_netdev "wlan0" "WLAN0" "mr18:blue:tricolor0" "wlan0"
+	;;
+
 mr600)
 	ucidef_set_led_wlan "wlan58" "WLAN58" "mr600:green:wlan58" "phy0tpt"
 	;;
diff --git a/target/linux/ar71xx/base-files/etc/uci-defaults/02_network b/target/linux/ar71xx/base-files/etc/uci-defaults/02_network
index 880953c..2be8d68 100644
--- a/target/linux/ar71xx/base-files/etc/uci-defaults/02_network
+++ b/target/linux/ar71xx/base-files/etc/uci-defaults/02_network
@@ -347,6 +347,7 @@ eap7660d |\
 el-mini |\
 loco-m-xw |\
 mr1750 |\
+mr18 |\
 mr600 |\
 mr600v2 |\
 mr900 |\
diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh
index efb3d16..ed20e16 100755
--- a/target/linux/ar71xx/base-files/lib/ar71xx.sh
+++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh
@@ -520,6 +520,9 @@ ar71xx_board_detect() {
 	*MR16)
 		name="mr16"
 		;;
+	*MR18)
+		name="mr18"
+		;;
 	*MR600v2)
 		name="mr600v2"
 		;;
diff --git a/target/linux/ar71xx/base-files/lib/preinit/05_set_iface_mac_ar71xx b/target/linux/ar71xx/base-files/lib/preinit/05_set_iface_mac_ar71xx
index 92b3765..a9f4bf5 100644
--- a/target/linux/ar71xx/base-files/lib/preinit/05_set_iface_mac_ar71xx
+++ b/target/linux/ar71xx/base-files/lib/preinit/05_set_iface_mac_ar71xx
@@ -29,6 +29,10 @@ preinit_set_mac_address() {
 		dir-615-i1)
 			fetch_mac_from_mtd nvram sys_lan_mac sys_wan_mac
 			;;
+		mr18)
+			mac_lan=$(mtd_get_mac_binary_ubi board-config 102)
+			[ -n "$mac_lan" ] && ifconfig eth0 hw ether "$mac_lan"
+			;;
 		r6100)
 			mac_lan=$(mtd_get_mac_binary caldata 0)
 			[ -n "$mac_lan" ] && ifconfig eth1 hw ether "$mac_lan"
diff --git a/target/linux/ar71xx/base-files/lib/upgrade/merakinand.sh b/target/linux/ar71xx/base-files/lib/upgrade/merakinand.sh
new file mode 100644
index 0000000..fe78e9f
--- /dev/null
+++ b/target/linux/ar71xx/base-files/lib/upgrade/merakinand.sh
@@ -0,0 +1,137 @@
+#!/bin/sh
+#
+# Copyright (C) 2015 Chris Blake <chrisrblake93 at gmail.com>
+#
+# Custom upgrade script for Meraki NAND devices (ex. MR18)
+# Based on dir825.sh and stock nand functions
+#
+. /lib/ar71xx.sh
+. /lib/functions.sh
+. /lib/upgrade/nand.sh
+
+get_magic_at() {
+	local mtddev=$1
+	local pos=$2
+	dd bs=1 count=2 skip=$pos if=$mtddev 2>/dev/null | hexdump -v -n 4 -e '1/1 "%02x"'
+}
+
+mr18_is_caldata_valid() {
+	local mtddev=$1
+	local magic
+
+	magic=$(get_magic_at $mtddev 4096)
+	[ "$magic" != "0202" ] && return 0
+
+	magic=$(get_magic_at $mtddev 20480)
+	[ "$magic" != "0202" ] && return 0
+
+	magic=$(get_magic_at $mtddev 36864)
+	[ "$magic" != "0202" ] && return 0
+
+	return 1
+}
+
+merakinand_copy_caldata() {
+	local cal_src=$1
+	local cal_dst=$2
+	local ubidev=$( nand_find_ubi $CI_UBIPART )
+	local board_name="$(cat /tmp/sysinfo/board_name)"
+	local rootfs_size="$(ubinfo /dev/ubi0 -N rootfs_data | grep "Size" | awk '{ print $6 }')"
+
+	# Setup partitions using board name, in case of future platforms
+	case "$board_name" in
+	"mr18")
+		# Src is MTD
+		mtd_src=$(find_mtd_chardev $cal_src)
+		[ -n "$mtd_src" ] || {
+			echo "no mtd device found for partition $cal_src"
+			exit 1
+		}
+
+		# Dest is UBI
+		# TODO: possibly add create (hard to do when rootfs_data is expanded & mounted)
+		# Would need to be done from ramdisk
+		mtd_dst="$(nand_find_volume $ubidev $cal_dst)"
+		[ -n "$mtd_dst" ] || {
+			echo "no ubi device found for partition $cal_dst"
+			exit 1
+		}
+
+		mr18_is_caldata_valid "$mtd_src" && {
+			echo "no valid calibration data found in $cal_src"
+			exit 1
+		}
+
+		mr18_is_caldata_valid "/dev/$mtd_dst" && {
+			echo "Copying calibration data from $cal_src to $cal_dst..."
+			dd if="$mtd_src" of=/tmp/caldata.tmp 2>/dev/null
+			ubiupdatevol "/dev/$mtd_dst" /tmp/caldata.tmp
+			rm /tmp/caldata.tmp
+			sync
+		}
+		return 0
+		;;
+	*)
+		echo "Unsupported device $board_name";
+		return 1
+		;;
+	esac
+}
+
+merakinand_do_kernel_check() {
+	local board_name="$1"
+	local tar_file="$2"
+	local image_magic_word=`(tar xf $tar_file sysupgrade-$board_name/kernel -O 2>/dev/null | dd bs=1 count=4 skip=0 2>/dev/null | hexdump -v -n 4 -e '1/1 "%02x"')`
+
+	# What is our kernel magic string?
+	case "$board_name" in
+	"mr18")
+		[ "$image_magic_word" == "8e73ed8a" ] && {
+			echo "pass" && return 0
+		}
+		;;
+	esac
+
+	exit 1
+}
+
+merakinand_do_platform_check() {
+	local board_name="$1"
+	local tar_file="$2"
+	local control_length=`(tar xf $tar_file sysupgrade-$board_name/CONTROL -O | wc -c) 2> /dev/null`
+	local file_type="$(identify_tar $2 sysupgrade-$board_name/root)"
+	local kernel_magic="$(merakinand_do_kernel_check $1 $2)"
+
+	case "$board_name" in
+	"mr18")
+		[ "$control_length" = 0 -o "$file_type" != "squashfs" -o "$kernel_magic" != "pass" ] && {
+			echo "Invalid sysupgrade file for $board_name"
+			return 1
+		}
+		;;
+	*)
+		echo "Unsupported device $board_name";
+		return 1
+		;;
+	esac
+
+	return 0
+}
+
+merakinand_do_upgrade() {
+	local tar_file="$1"
+	local board_name="$(cat /tmp/sysinfo/board_name)"
+
+	# Do we need to do any platform tweaks?
+	case "$board_name" in
+	"mr18")
+		# Check and create UBI caldata if it's invalid
+		merakinand_copy_caldata "odm-caldata" "caldata"
+		nand_do_upgrade $1
+		;;
+	*)
+		echo "Unsupported device $board_name";
+		exit 1
+		;;
+	esac
+}
diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
index cad8b43..e73e3fe 100755
--- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
@@ -424,6 +424,10 @@ platform_check_image() {
 		}
 		return 0
 		;;
+	mr18)
+		merakinand_do_platform_check $board $1
+		return $?;
+		;;
 	nbg6716 | \
 	r6100 | \
 	wndr3700v4 | \
@@ -484,6 +488,9 @@ platform_pre_upgrade() {
 	wndr4300 )
 		nand_do_upgrade "$1"
 		;;
+	mr18)
+		merakinand_do_upgrade "$1"
+		;;
 	esac
 }
 
diff --git a/target/linux/ar71xx/config-4.1 b/target/linux/ar71xx/config-4.1
index 51f2f2f..8fff692 100644
--- a/target/linux/ar71xx/config-4.1
+++ b/target/linux/ar71xx/config-4.1
@@ -84,6 +84,7 @@ CONFIG_ATH79_MACH_MC_MAC1200R=y
 CONFIG_ATH79_MACH_MR12=y
 CONFIG_ATH79_MACH_MR16=y
 CONFIG_ATH79_MACH_MR1750=y
+CONFIG_ATH79_MACH_MR18=y
 CONFIG_ATH79_MACH_MR600=y
 CONFIG_ATH79_MACH_MR900=y
 CONFIG_ATH79_MACH_MYNET_N600=y
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-mr18.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-mr18.c
new file mode 100644
index 0000000..1ce5c83
--- /dev/null
+++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-mr18.c
@@ -0,0 +1,254 @@
+/*
+ *  Cisco Meraki MR18 board support
+ *
+ *  Copyright (C) 2015 Chris Blake <chrisrblake93 at gmail.com>
+ *  Copyright (C) 2015 Christian Lamparter <chunkeey at googlemail.com>
+ *  Copyright (C) 2015 Thomas Hebb <tommyhebb at gmail.com>
+ *
+ *  Based on Cisco Meraki GPL Release r23-20150601 MR18 Device Config
+ *
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License version 2 as published
+ *  by the Free Software Foundation.
+ */
+#include <linux/platform_device.h>
+#include <linux/ath9k_platform.h>
+#include <linux/platform/ar934x_nfc.h>
+#include <linux/platform_data/phy-at803x.h>
+
+#include <asm/mach-ath79/ath79.h>
+#include <asm/mach-ath79/ar71xx_regs.h>
+
+#include <linux/leds-nu801.h>
+#include <linux/pci.h>
+
+#include "common.h"
+#include "dev-eth.h"
+#include "pci.h"
+#include "dev-gpio-buttons.h"
+#include "dev-leds-gpio.h"
+#include "dev-nfc.h"
+#include "dev-wmac.h"
+#include "machtypes.h"
+
+#define MR18_GPIO_LED_POWER_WHITE    18
+#define MR18_GPIO_LED_POWER_ORANGE    21
+
+#define MR18_GPIO_BTN_RESET    17
+#define MR18_KEYS_POLL_INTERVAL    20  /* msecs */
+#define MR18_KEYS_DEBOUNCE_INTERVAL  (3 * MR18_KEYS_POLL_INTERVAL)
+
+#define MR18_WAN_PHYADDR    3
+
+/* used for eth calibration */
+#define MR18_OTP_BASE			(AR71XX_APB_BASE + 0x130000)
+#define MR18_OTP_SIZE			(0x2000) /* just a guess */
+#define MR18_OTP_MEM_0_REG		(0x0000)
+#define MR18_OTP_INTF2_REG		(0x1008)
+#define MR18_OTP_STATUS0_REG		(0x1018)
+#define MR18_OTP_STATUS0_EFUSE_VALID	BIT(2)
+
+#define MR18_OTP_STATUS1_REG		(0x101c)
+#define MR18_OTP_LDO_CTRL_REG		(0x1024)
+#define MR18_OTP_LDO_STATUS_REG		(0x102c)
+#define MR18_OTP_LDO_STATUS_POWER_ON	BIT(0)
+
+static struct gpio_led MR18_leds_gpio[] __initdata = {
+	{
+		.name = "mr18:white:power",
+		.gpio = MR18_GPIO_LED_POWER_WHITE,
+		.active_low  = 1,
+	}, {
+		.name = "mr18:orange:power",
+		.gpio = MR18_GPIO_LED_POWER_ORANGE,
+		.active_low  = 0,
+	},
+};
+
+static struct gpio_keys_button MR18_gpio_keys[] __initdata = {
+	{
+		.desc = "reset",
+		.type = EV_KEY,
+		.code = KEY_RESTART,
+		.debounce_interval = MR18_KEYS_DEBOUNCE_INTERVAL,
+		.gpio    = MR18_GPIO_BTN_RESET,
+		.active_low  = 1,
+	},
+};
+
+static struct led_nu801_template tricolor_led_template = {
+	.device_name = "mr18",
+	.name = "tricolor",
+	.num_leds = 1,
+	.cki = 11,
+	.sdi = 12,
+	.lei = -1,
+	.ndelay = 500,
+	.init_brightness = {
+		LED_OFF,
+		LED_OFF,
+		LED_OFF,
+	},
+	.default_trigger = "none",
+	.led_colors = { "red", "green", "blue" },
+};
+
+static struct led_nu801_platform_data tricolor_led_data = {
+	.num_controllers = 1,
+	.template = &tricolor_led_template,
+};
+
+static struct platform_device tricolor_leds = {
+	.name = "leds-nu801",
+	.id = -1,
+	.dev.platform_data = &tricolor_led_data,
+};
+
+static int mr18_extract_sgmii_res_cal(void)
+{
+	void __iomem *base;
+	unsigned int reversed_sgmii_value;
+
+	unsigned int otp_value, otp_per_val, rbias_per, read_data;
+	unsigned int rbias_pos_or_neg;
+	unsigned int sgmii_res_cal_value;
+	int res_cal_val;
+
+	base = ioremap_nocache(MR18_OTP_BASE, MR18_OTP_SIZE);
+	if (!base)
+		return -EIO;
+
+	__raw_writel(0x7d, base + MR18_OTP_INTF2_REG);
+	__raw_writel(0x00, base + MR18_OTP_LDO_CTRL_REG);
+
+	while (__raw_readl(base + MR18_OTP_LDO_STATUS_REG) &
+		MR18_OTP_LDO_STATUS_POWER_ON);
+
+	__raw_readl(base + MR18_OTP_MEM_0_REG + 4);
+
+	while (!(__raw_readl(base + MR18_OTP_STATUS0_REG) &
+		MR18_OTP_STATUS0_EFUSE_VALID));
+
+	read_data = __raw_readl(base + MR18_OTP_STATUS1_REG);
+
+	iounmap(base);
+
+	if (!(read_data & 0x1fff))
+		return -ENODEV;
+
+	if (read_data & 0x00001000)
+		otp_value = (read_data & 0xfc0) >> 6;
+	else
+		otp_value = read_data & 0x3f;
+
+	if (otp_value > 31) {
+		otp_per_val = 63 - otp_value;
+		rbias_pos_or_neg = 1;
+	} else {
+		otp_per_val = otp_value;
+		rbias_pos_or_neg = 0;
+	}
+
+	rbias_per = otp_per_val * 15;
+
+	if (rbias_pos_or_neg == 1)
+		res_cal_val = (rbias_per + 34) / 21;
+	else if (rbias_per > 34)
+		res_cal_val = -((rbias_per - 34) / 21);
+	else
+		res_cal_val = (34 - rbias_per) / 21;
+
+	sgmii_res_cal_value = (8 + res_cal_val) & 0xf;
+
+	reversed_sgmii_value  = (sgmii_res_cal_value & 8) >> 3;
+	reversed_sgmii_value |= (sgmii_res_cal_value & 4) >> 1;
+	reversed_sgmii_value |= (sgmii_res_cal_value & 2) << 1;
+	reversed_sgmii_value |= (sgmii_res_cal_value & 1) << 3;
+	printk(KERN_INFO "SGMII cal value = 0x%x\n", reversed_sgmii_value);
+	return reversed_sgmii_value;
+}
+
+static struct ath9k_platform_data pci_main_wifi_data = {
+	.led_pin = -1,
+};
+static struct ath9k_platform_data pci_scan_wifi_data = {
+	.led_pin = -1,
+};
+
+static int mr18_dual_pci_plat_dev_init(struct pci_dev *dev)
+{
+	/* The PCIE devices are attached to different busses but they
+	 * both share the same slot number. Checking the PCI_SLOT vals
+	 * does not work.
+	 */
+	switch (dev->bus->number) {
+	case 0:
+		dev->dev.platform_data = &pci_main_wifi_data;
+		break;
+	case 1:
+		dev->dev.platform_data = &pci_scan_wifi_data;
+		break;
+	}
+
+	return 0;
+}
+
+static void __init mr18_setup(void)
+{
+	int res;
+
+	/* NAND */
+	ath79_nfc_set_ecc_mode(AR934X_NFC_ECC_SOFT_BCH);
+	ath79_register_nfc();
+
+	/* even though, the PHY is connected via RGMII,
+	 * the SGMII/SERDES PLLs need to be calibrated and locked.
+	 * Or else, the PHY won't be working for this platfrom.
+	 *
+	 * Figuring this out took such a long time, that we want to
+	 * point this quirk out, before someone wants to remove it.
+	 */
+	res = mr18_extract_sgmii_res_cal();
+	if (res >= 0) {
+		/* Setup SoC Eth Config */
+		ath79_setup_qca955x_eth_cfg(QCA955X_ETH_CFG_RGMII_EN);
+		ath79_setup_qca955x_eth_rx_delay(3, 3);
+
+		/* MDIO Interface */
+		ath79_register_mdio(0, 0x0);
+
+		ath79_setup_qca955x_eth_serdes_cal(res);
+
+		/* GMAC0 is connected to an Atheros AR8035-A */
+		ath79_init_mac(ath79_eth0_data.mac_addr, NULL, 0);
+		ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
+		ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
+		ath79_eth0_data.phy_mask = BIT(MR18_WAN_PHYADDR);
+		ath79_eth0_pll_data.pll_1000 = 0xa6000000;
+		ath79_eth0_pll_data.pll_100 = 0xa0000101;
+		ath79_eth0_pll_data.pll_10 = 0x80001313;
+		ath79_register_eth(0);
+	} else {
+		printk(KERN_ERR "failed to read EFUSE for ethernet cal\n");
+	}
+
+	/* LEDs and Buttons */
+	platform_device_register(&tricolor_leds);
+	ath79_register_leds_gpio(-1, ARRAY_SIZE(MR18_leds_gpio),
+				 MR18_leds_gpio);
+	ath79_register_gpio_keys_polled(-1, MR18_KEYS_POLL_INTERVAL,
+					ARRAY_SIZE(MR18_gpio_keys),
+					MR18_gpio_keys);
+
+	/* Clear RTC reset (Needed by SoC WiFi) */
+	ath79_device_reset_clear(QCA955X_RESET_RTC);
+
+	/* WiFi */
+	ath79_register_wmac_simple();
+
+	pci_main_wifi_data.eeprom_name = "pci_wmac0.eeprom";
+	pci_scan_wifi_data.eeprom_name = "pci_wmac1.eeprom";
+	ath79_pci_set_plat_dev_init(mr18_dual_pci_plat_dev_init);
+	ath79_register_pci();
+}
+MIPS_MACHINE(ATH79_MACH_MR18, "MR18", "Meraki MR18", mr18_setup);
diff --git a/target/linux/ar71xx/image/Makefile b/target/linux/ar71xx/image/Makefile
index b00846f..f18aa05 100644
--- a/target/linux/ar71xx/image/Makefile
+++ b/target/linux/ar71xx/image/Makefile
@@ -1273,6 +1273,7 @@ dragino2_mtdlayout=mtdparts=spi0.0:256k(u-boot)ro,16000k(firmware),64k(config)ro
 hiwifi_hc6361_mtdlayout=mtdparts=spi0.0:64k(u-boot)ro,64k(bdinfo)ro,1280k(kernel),14848k(rootfs),64k(backup)ro,64k(art)ro,16128k at 0x20000(firmware)
 mr12_mtdlayout=mtdparts=spi0.0:256k(u-boot)ro,256k(u-boot-env)ro,13440k(rootfs),2304k(kernel),128k(art)ro,15744k at 0x80000(firmware)
 mr16_mtdlayout=mtdparts=spi0.0:256k(u-boot)ro,256k(u-boot-env)ro,13440k(rootfs),2304k(kernel),128k(art)ro,15744k at 0x80000(firmware)
+mr18_mtdlayout=mtdparts=ar934x-nfc:512k(nandloader)ro,8M(kernel),8M(recovery),113664k(ubi),128k at 130944k(odm-caldata)ro
 pb92_mtdlayout=mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,2752k(rootfs),896k(kernel),64k(nvram),64k(art)ro,3648k at 0x50000(firmware)
 planex_mtdlayout=mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,7744k(firmware),128k(art)ro
 ubntxm_mtdlayout=mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,7552k(firmware),256k(cfg)ro,64k(EEPROM)ro
@@ -1877,6 +1878,37 @@ Image/Build/CyberTANLZMA/buildkernel=$(call MkuImageLzma,$(2),$(3) $(4))
 Image/Build/CyberTANLZMA=$(call Image/Build/CyberTAN,$(1),$(2),$(3),$(4),$(5))
 
 
+define Image/Build/MerakiNAND/initramfs
+	$(eval kernelsize=$(call mtdpartsize,kernel,$(4)))
+	$(call PatchKernel,$(2),$(3) $(4),"-initramfs")
+	-$(STAGING_DIR_HOST)/bin/mkmerakifw \
+		-B $(2) -s \
+		-i $(KDIR_TMP)/vmlinux-initramfs-$(2) \
+		-o $(KDIR_TMP)/vmlinux-initramfs-$(2)-patched
+	$(CP) $(KDIR_TMP)/vmlinux-initramfs-$(2)-patched $(BIN_DIR)/$(IMG_PREFIX)-$(2)-initramfs.bin
+endef
+
+define Image/Build/MerakiNAND/buildkernel
+	$(eval kernelsize=$(call mtdpartsize,kernel,$(4)))
+	$(call PatchKernel,$(2),$(3) $(4),"")
+	-$(STAGING_DIR_HOST)/bin/mkmerakifw \
+		-B $(2) -s \
+		-i $(KDIR_TMP)/vmlinux-$(2) \
+		-o $(KDIR_TMP)/vmlinux-$(2)-patched
+	$(CP) $(KDIR_TMP)/vmlinux-$(2)-patched $(BIN_DIR)/$(IMG_PREFIX)-$(2)-kernel.bin
+
+endef
+
+define Image/Build/MerakiNAND
+	$(eval fwsize=$(call mtdpartsize,firmware,$(4)))
+	$(eval rootsize=$(call mtdpartsize,rootfs,$(4)))
+	$(eval kernsize=$(call mtdpartsize,kernel,$(4)))
+	dd if=$(KDIR)/root.$(1) \
+			of=$(call imgname,$(1),$(2)-rootfs).bin bs=128k conv=sync; \
+	$(call Image/Build/SysupgradeNAND,$(2),squashfs,$(KDIR_TMP)/vmlinux-$(2)-patched)
+endef
+
+
 Image/Build/Netgear/initramfs=$(call MkuImageLzma/initramfs,$(2),$(3) $(4),,-M $(5))
 
 define Image/Build/Netgear/buildkernel
@@ -2323,6 +2355,8 @@ $(eval $(call MultiProfile,Madwifi,EAP7660D WP543))
 endif # ifeq ($(SUBTARGET),generic)
 
 ifeq ($(SUBTARGET),nand)
+$(eval $(call SingleProfile,MerakiNAND,64k,MR18,mr18,MR18,ttyS0,115200,$$(mr18_mtdlayout)))
+
 $(eval $(call SingleProfile,NetgearNAND,64k,WNDR3700V4,wndr3700v4,WNDR3700_V4,ttyS0,115200,$$(wndr4300_mtdlayout),0x33373033,WNDR3700v4,"",-H 29763948+128+128,wndr4300))
 $(eval $(call SingleProfile,NetgearNAND,64k,WNDR4300V1,wndr4300,WNDR4300,ttyS0,115200,$$(wndr4300_mtdlayout),0x33373033,WNDR4300,"",-H 29763948+0+128+128+2x2+3x3,wndr4300))
 $(eval $(call SingleProfile,NetgearNAND,64k,R6100,r6100,R6100,ttyS0,115200,$$(r6100_mtdlayout),0x36303030,R6100,"",-H 29764434+0+128+128+2x2+2x2,wndr4300))
diff --git a/target/linux/ar71xx/nand/config-default b/target/linux/ar71xx/nand/config-default
index 50b6dbe..05f52af 100644
--- a/target/linux/ar71xx/nand/config-default
+++ b/target/linux/ar71xx/nand/config-default
@@ -91,6 +91,7 @@ CONFIG_MTD_NAND=y
 CONFIG_MTD_NAND_AR934X=y
 CONFIG_MTD_NAND_AR934X_HW_ECC=y
 CONFIG_MTD_NAND_ECC=y
+CONFIG_MTD_NAND_ECC_BCH=y
 # CONFIG_MTD_REDBOOT_PARTS is not set
 # CONFIG_MTD_SM_COMMON is not set
 # CONFIG_MTD_SPLIT_SEAMA_FW is not set
diff --git a/target/linux/ar71xx/nand/profiles/meraki.mk b/target/linux/ar71xx/nand/profiles/meraki.mk
new file mode 100644
index 0000000..2c848c9
--- /dev/null
+++ b/target/linux/ar71xx/nand/profiles/meraki.mk
@@ -0,0 +1,17 @@
+#
+# Copyright (C) 2014-2015 Chris Blake (chrisrblake93 at gmail.com)
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/MR18
+	NAME:=Meraki MR18
+	PACKAGES:=kmod-spi-gpio kmod-ath9k
+endef
+
+define Profile/MR18/description
+	Package set optimized for the Cisco Meraki MR18 Access Point.
+endef
+
+$(eval $(call Profile,MR18))
diff --git a/target/linux/ar71xx/patches-4.1/817-MIPS-ath79-add-meraki-mr18-support.patch b/target/linux/ar71xx/patches-4.1/817-MIPS-ath79-add-meraki-mr18-support.patch
new file mode 100644
index 0000000..a36075a
--- /dev/null
+++ b/target/linux/ar71xx/patches-4.1/817-MIPS-ath79-add-meraki-mr18-support.patch
@@ -0,0 +1,41 @@
+--- a/arch/mips/ath79/Kconfig
++++ b/arch/mips/ath79/Kconfig
+@@ -824,6 +824,17 @@ config ATH79_MACH_MR16
+        select ATH79_DEV_M25P80
+        select ATH79_DEV_WMAC
+
++config ATH79_MACH_MR18
++	bool "Meraki MR18 board support"
++	select SOC_QCA955X
++	select ATH79_DEV_AP9X_PCI if PCI
++	select ATH79_DEV_ETH
++	select ATH79_DEV_GPIO_BUTTONS
++	select ATH79_DEV_LEDS_GPIO
++	select ATH79_DEV_NFC
++	select ATH79_DEV_WMAC
++	select LEDS_NU801
++
+ config ATH79_MACH_MR600
+        bool "OpenMesh MR600 board support"
+        select SOC_AR934X
+
+--- a/arch/mips/ath79/Makefile
++++ b/arch/mips/ath79/Makefile
+@@ -91,6 +91,7 @@ obj-$(CONFIG_ATH79_MACH_HORNET_UB)	+= ma
+ obj-$(CONFIG_ATH79_MACH_MC_MAC1200R)     += mach-mc-mac1200r.o
+ obj-$(CONFIG_ATH79_MACH_MR12)		+= mach-mr12.o
+ obj-$(CONFIG_ATH79_MACH_MR16)		+= mach-mr16.o
++obj-$(CONFIG_ATH79_MACH_MR18)		+= mach-mr18.o
+ obj-$(CONFIG_ATH79_MACH_MR1750)		+= mach-mr1750.o
+ obj-$(CONFIG_ATH79_MACH_MR600)		+= mach-mr600.o
+ obj-$(CONFIG_ATH79_MACH_MR900)		+= mach-mr900.o
+--- a/arch/mips/ath79/machtypes.h
++++ b/arch/mips/ath79/machtypes.h
+@@ -80,6 +80,7 @@ enum ath79_mach_type {
+ 	ATH79_MACH_HORNET_UB,		/* ALFA Networks Hornet-UB */
+ 	ATH79_MACH_MR12,		/* Cisco Meraki MR12 */
+ 	ATH79_MACH_MR16,		/* Cisco Meraki MR16 */
++	ATH79_MACH_MR18,		/* Cisco Meraki MR18 */
+ 	ATH79_MACH_MR1750,		/* OpenMesh MR1750 */
+ 	ATH79_MACH_MR600V2,		/* OpenMesh MR600v2 */
+ 	ATH79_MACH_MR600,		/* OpenMesh MR600 */
-- 
2.5.3
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel



More information about the openwrt-devel mailing list