[OpenWrt-Devel] [PATCH] Add support for ZTE Q7

郭传鈜 gch981213 at gmail.com
Tue Mar 31 07:45:53 EDT 2015


Sorry I forgot to edit the title.This is a router with MT7620a SoC so
it belongs to ramips target.


2015-03-31 19:38 GMT+08:00 郭传鈜 <gch981213 at gmail.com>:

> ZTE Q7 is a wireless router with SD Card,USB,1 ethernet port and a battery.
> I can,t find any information about this router on ZTE's website.
> But I found this : http://en.cctairmobi.com/plus/list.php?tid=40
> This router is the same as ZTE Q7 and later I found that both routers are
> made by the same company:-D
>
> This patch adds support for it.
> Because there is only one port,I disabled VLAN and use eth0 as lan port.
> I could only create a sysupgrade firmware because I don't know how the
> orignal webpage check the uploaded image:-(
> Signed-off-by: 郭传鈜 <gch981213 at gmail.com>
>
> ---
>  target/linux/ramips/base-files/etc/board.d/01_leds |   3 +
>  .../linux/ramips/base-files/etc/board.d/02_network |   1 +
>  target/linux/ramips/base-files/etc/diag.sh         |   3 +
>  target/linux/ramips/base-files/lib/ramips.sh       |   3 +
>  .../ramips/base-files/lib/upgrade/platform.sh      |   1 +
>  target/linux/ramips/dts/ZTE-Q7.dts                 | 111
> +++++++++++++++++++++
>  target/linux/ramips/image/Makefile                 |   2 +
>  7 files changed, 124 insertions(+)
>  create mode 100644 target/linux/ramips/dts/ZTE-Q7.dts
>
> diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds
> b/target/linux/ramips/base-files/etc/board.d/01_leds
> index bfe1c0c..56ba3b7 100755
> --- a/target/linux/ramips/base-files/etc/board.d/01_leds
> +++ b/target/linux/ramips/base-files/etc/board.d/01_leds
> @@ -237,6 +237,9 @@ case $board in
>                 set_usb_led "lenovo:blue:usb"
>                 set_wifi_led "lenovo:blue:wifi"
>                 ;;
> +       zte-q7)
> +               set_wifi_led "zte:blue:status"
> +               ;;
>  esac
>
>  board_config_flush
> diff --git a/target/linux/ramips/base-files/etc/board.d/02_network
> b/target/linux/ramips/base-files/etc/board.d/02_network
> index 89d1681..d4ec19d 100755
> --- a/target/linux/ramips/base-files/etc/board.d/02_network
> +++ b/target/linux/ramips/base-files/etc/board.d/02_network
> @@ -46,6 +46,7 @@ ramips_setup_interfaces()
>         3g150b | \
>         3g300m | \
>         w150m | \
> +       zte-q7 | \
>         all0256n | \
>         all5002 | \
>         all5003 | \
> diff --git a/target/linux/ramips/base-files/etc/diag.sh
> b/target/linux/ramips/base-files/etc/diag.sh
> index 50b6ff2..5301593 100644
> --- a/target/linux/ramips/base-files/etc/diag.sh
> +++ b/target/linux/ramips/base-files/etc/diag.sh
> @@ -224,6 +224,9 @@ get_status_led() {
>         y1s)
>                 status_led="lenovo:blue:power"
>                 ;;
> +       zte-q7)
> +               status_led="zte:red:status"
> +               ;;
>         esac
>  }
>
> diff --git a/target/linux/ramips/base-files/lib/ramips.sh
> b/target/linux/ramips/base-files/lib/ramips.sh
> index 4527414..fc6eb37 100755
> --- a/target/linux/ramips/base-files/lib/ramips.sh
> +++ b/target/linux/ramips/base-files/lib/ramips.sh
> @@ -379,6 +379,9 @@ ramips_board_detect() {
>         *"ZBT WR8305RT")
>                 name="wr8305rt"
>                 ;;
> +       *"ZTE Q7")
> +               name="zte-q7"
> +               ;;
>         *"Lenovo Y1")
>                 name="y1"
>                 ;;
> diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh
> b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> index fffbe72..a5773b5 100755
> --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
> +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> @@ -114,6 +114,7 @@ platform_check_image() {
>         xiaomi-miwifi-mini |\
>         y1 |\
>         y1s |\
> +       zte-q7 |\
>         zbt-wa05)
>                 [ "$magic" != "27051956" ] && {
>                         echo "Invalid image type."
> diff --git a/target/linux/ramips/dts/ZTE-Q7.dts
> b/target/linux/ramips/dts/ZTE-Q7.dts
> new file mode 100644
> index 0000000..9efc35e
> --- /dev/null
> +++ b/target/linux/ramips/dts/ZTE-Q7.dts
> @@ -0,0 +1,111 @@
> +/dts-v1/;
> +
> +/include/ "mt7620a.dtsi"
> +
> +/ {
> +       compatible = "ZTE-Q7", "ralink,mt7620a-soc";
> +       model = "ZTE Q7";
> +
> +       palmbus at 10000000 {
> +
> +               gpio0: gpio at 600 {
> +                       status = "okay";
> +               };
> +
> +               gpio1: gpio at 638 {
> +                       status = "okay";
> +               };
> +
> +               spi at b00 {
> +                       status = "okay";
> +
> +                       m25p80 at 0 {
> +                               #address-cells = <1>;
> +                               #size-cells = <1>;
> +                               compatible = "en25q64";
> +                               reg = <0 0>;
> +                               linux,modalias = "m25p80", "en25q64";
> +                               spi-max-frequency = <10000000>;
> +
> +                               partition at 0 {
> +                                       label = "u-boot";
> +                                       reg = <0x0 0x30000>;
> +                                       read-only;
> +                               };
> +
> +                               partition at 30000 {
> +                                       label = "u-boot-env";
> +                                       reg = <0x30000 0x10000>;
> +                                       read-only;
> +                               };
> +
> +                               factory: partition at 40000 {
> +                                       label = "factory";
> +                                       reg = <0x40000 0x10000>;
> +                                       read-only;
> +                               };
> +
> +                               partition at 50000 {
> +                                       label = "firmware";
> +                                       reg = <0x50000 0x7b0000>;
> +                               };
> +                       };
> +               };
> +       };
> +
> +       pinctrl {
> +               state_default: pinctrl0 {
> +                       gpio {
> +                               ralink,group = "i2c", "uartf", "rgmii1",
> "rgmii2", "ephy", "wled", "nd_sd";
> +                               ralink,function = "gpio";
> +                       };
> +               };
> +       };
> +
> +       ethernet at 10100000 {
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&ephy_pins>;
> +               mtd-mac-address = <&factory 0x4>;
> +               ralink,port-map = "wllll";
> +       };
> +
> +       wmac at 10180000 {
> +               ralink,mtd-eeprom = <&factory 0>;
> +       };
> +
> +       sdhci at 10130000 {
> +               status = "okay";
> +       };
> +
> +       ehci at 101c0000 {
> +               status = "okay";
> +       };
> +
> +       ohci at 101c1000 {
> +               status = "okay";
> +       };
> +
> +       gpio-leds {
> +               compatible = "gpio-leds";
> +               statred {
> +                       label = "zte:red:status";
> +                       gpios = <&gpio0 13 1>;
> +               };
> +               statblue {
> +                       label = "zte:blue:status";
> +                       gpios = <&gpio0 9 1>;
> +               };
> +       };
> +
> +       gpio-keys-polled {
> +               compatible = "gpio-keys-polled";
> +               #address-cells = <1>;
> +               #size-cells = <0>;
> +               poll-interval = <20>;
> +               reset {
> +                       label = "reset";
> +                       gpios = <&gpio1 2 1>;
> +                       linux,code = <0x198>;
> +               };
> +       };
> +};
> diff --git a/target/linux/ramips/image/Makefile
> b/target/linux/ramips/image/Makefile
> index 45ae3a5..bc1fe181 100644
> --- a/target/linux/ramips/image/Makefile
> +++ b/target/linux/ramips/image/Makefile
> @@ -862,6 +862,7 @@ Image/Build/Profile/WR8305RT=$(call
> BuildFirmware/Default8M/$(1),$(1),wr8305rt,W
>  Image/Build/Profile/WRTNODE=$(call
> BuildFirmware/Default16M/$(1),$(1),wrtnode,WRTNODE)
>  Image/Build/Profile/WT3020=$(call
> BuildFirmware/PorayDualSize/$(1),$(1),wt3020,WT3020)
>  Image/Build/Profile/XIAOMI-MIWIFI-MINI=$(call
> BuildFirmware/Default16M/$(1),$(1),xiaomi-miwifi-mini,XIAOMI-MIWIFI-MINI)
> +Image/Build/Profile/ZTE-Q7=$(call
> BuildFirmware/Default8M/$(1),$(1),zte-q7,ZTE-Q7)
>  Image/Build/Profile/ZBT-WA05=$(call
> BuildFirmware/Default8M/$(1),$(1),zbt-wa05,ZBT-WA05)
>  Image/Build/Profile/ArcherC20i=$(call
> BuildFirmware/Tplink/$(1),$(1),ArcherC20i,ArcherC20i)
>
> @@ -891,6 +892,7 @@ define Image/Build/Profile/Default
>         $(call Image/Build/Profile/WRTNODE,$(1))
>         $(call Image/Build/Profile/WT3020,$(1))
>         $(call Image/Build/Profile/XIAOMI-MIWIFI-MINI,$(1))
> +       $(call Image/Build/Profile/ZTE-Q7,$(1))
>         $(call Image/Build/Profile/ZBT-WA05,$(1))
>         $(call Image/Build/Profile/ArcherC20i,$(1))
>  endef
> --
> 2.1.0
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.infradead.org/pipermail/openwrt-devel/attachments/20150331/707a9120/attachment.htm>
-------------- next part --------------
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel


More information about the openwrt-devel mailing list