[OpenWrt-Devel] [PATCH] ramips: Buffalo WZR-AGL300NH target support

ngc-IIJ ngc at ff.iij4u.or.jp
Mon Feb 16 07:06:43 EST 2015


I got work with this patch.
Ethernet switch (includes VLAN), WiFi connected via PCIe, LEDs, buttons.

In mtd partion map of DTS file, I renamed Linux firmware regions (kernel + root squashfs) to “firmware”because it allows kernel to split kernel and roots and rootfsdata.


signed-off-by: ngc at ff.iij4u.or.jp
——
--- a/target/linux/ramips/base-files/etc/board.d/02_network	2015-01-05 20:51:44.510050748 +0900
+++ b/target/linux/ramips/base-files/etc/board.d/02_network	2015-02-11 12:20:00.751290483 +0900
@@ -235,6 +235,12 @@ ramips_setup_interfaces()
 		ucidef_add_switch_vlan "switch1" "2" "4 6t"
 		;;
 
+	wzr-agl300nh)
+		ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
+		ucidef_add_switch "switch0" "1" "1"
+		ucidef_add_switch_vlan "switch0" "1" "1 2 3 4 5t"
+		ucidef_add_switch_vlan "switch0" "2" "0 5t"
+		;;
 	*)
 		RT3X5X=`cat /proc/cpuinfo | egrep "(RT3.5|RT5350)"`
 		if [ -n "${RT3X5X}" ]; then
--- a/target/linux/ramips/base-files/etc/diag.sh	2015-01-05 20:51:44.511050748 +0900
+++ b/target/linux/ramips/base-files/etc/diag.sh	2015-02-07 19:38:52.882546591 +0900
@@ -164,6 +164,9 @@ get_status_led() {
 	wli-tx4-ag300n)
 		status_led="buffalo:blue:power"
 		;;
+	wzr-agl300nh)
+		status_led="buffalo:green:router"
+		;;
 	wl-351)
 		status_led="wl-351:amber:power"
 		;;
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh	2015-01-05 20:51:44.512050748 +0900
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh	2015-02-07 19:38:52.882546591 +0900
@@ -96,6 +96,7 @@ platform_check_image() {
 	wl-351 | \
 	wl341v3 | \
 	wli-tx4-ag300n | \
+	wzr-agl300nh | \
 	wmr300 |\
 	wnce2001 | \
 	wr512-3gn |\
--- a/target/linux/ramips/dts/WZR-AGL300NH.dts	1970-01-01 09:00:00.000000000 +0900
+++ b/target/linux/ramips/dts/WZR-AGL300NH.dts	2015-02-11 11:40:50.188586711 +0900
@@ -0,0 +1,135 @@
+/dts-v1/;
+
+/include/ "rt2880.dtsi"
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "WZR-AGL300NH", "ralink,rt2880-soc";
+	model = "Buffalo WZR-AGL300NH";
+
+	palmbus at 300000 {
+		gpio0: gpio at 600 {
+			status = "okay";
+		};
+	};
+
+	pinctrl {
+		state_default: pinctrl0 {
+			gpio {
+				ralink,group = "i2c", "uartlite", "mdio";
+				ralink,function = "gpio";
+			};
+		};
+	};
+
+	cfi at 1f000000 {
+		compatible = "cfi-flash";
+		reg = <0x1f000000 0x800000>;
+
+		bank-width = <2>;
+		device-width = <2>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition at 0 {
+			label = "uboot";
+			reg = <0x0 0x30000>;
+			read-only;
+		};
+		partition at 30000 {
+			label = "uboot-env";
+			reg = <0x30000 0x10000>;
+			read-only;
+		};
+		factory: partition at 40000 {
+			label = "factory";
+			reg = <0x40000 0x10000>;
+			read-only;
+		};
+		partition at 50000 {
+			label = "firmware";
+			reg = <0x50000 0x3b0000>;
+		};
+	};
+
+	ethernet at 400000 {
+		status = "okay";
+		mtd-mac-address = <&factory 0x4>;
+
+                port at 0 {
+			ralink,fixed-link = <1000 1 1 1>;
+		};
+
+		mdio-bus {
+			status = "okay";
+			phy0: ethernet-phy at 0 {
+				phy-mode = "mii";
+				reg = <0>;
+			};
+		};
+	};
+
+	rtl8366s {
+		compatible = "realtek,rtl8366s";
+		gpio-sda = <&gpio0 1 0>;
+		gpio-sck = <&gpio0 2 0>;
+	};
+
+	wmac at 480000 {
+		ralink,mtd-eeprom = <&factory 0>;
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <100>;
+		wps {
+			label = "wps";
+			gpios = <&gpio0 0 1>;
+			linux,code = <0x211>;
+		};
+		router {
+			label = "router_switch";
+			gpios = <&gpio0 7 0>;
+			linux,code = <0x100>;
+		};
+		reset {
+			label = "reset";
+			gpios = <&gpio0 9 1>;
+			linux,code = <0x198>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		router {
+			label = "buffalo:green:router";
+			gpios = <&gpio0 8 1>;
+		};
+		diag {
+			label = "buffalo:red:diag";
+			gpios = <&gpio0 12 1>;
+		};
+		security_g {
+			label = "buffalo:orange:security_g";
+			gpios = <&gpio0 11 1>;
+		};
+		security_n {
+			label = "buffalo:orange:security_n";
+			gpios = <&gpio0 13 1>;
+		};
+	};
+
+
+	pcibus0: pci at 00440000 {
+		compatible = "ralink,rt288x-pci";
+		reg = <0x00440000 0x20000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		status = "ok";
+	};
+};
--- a/target/linux/ramips/image/Makefile	2015-01-05 20:51:44.530050748 +0900
+++ b/target/linux/ramips/image/Makefile	2015-02-11 07:31:07.011577761 +0900
@@ -353,6 +353,8 @@ Image/Build/Profile/V11STFE=$(call Build
 
 Image/Build/Profile/WLITX4AG300N=$(call BuildFirmware/Default4M/$(1),$(1),wli-tx4-ag300n,WLI-TX4-AG300N)
 
+Image/Build/Profile/WZRAGL300NH=$(call BuildFirmware/Default4M/$(1),$(1),wzr-agl300nh,WZR-AGL300NH)
+
 ifeq ($(SUBTARGET),rt288x)
 define Image/Build/Profile/Default
 	$(call Image/Build/Profile/AR670W,$(1))
@@ -361,6 +363,7 @@ define Image/Build/Profile/Default
 	$(call Image/Build/Profile/RTN15,$(1))
 	$(call Image/Build/Profile/V11STFE,$(1))
 	$(call Image/Build/Profile/WLITX4AG300N,$(1))
+	$(call Image/Build/Profile/WZRAGL300NH,$(1))
 endef
 endif
 
——
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel


More information about the openwrt-devel mailing list