[PATCH v4] clk: axs10x: introduce AXS10X pll driver

[Eugeniy Paltsev]

On Tue, 2017-07-11 at 22:25 -0700, Stephen Boyd wrote:
> On 06/21, Eugeniy Paltsev wrote:
> > AXS10X boards manages it's clocks using various PLLs. These PLL has
> > same
> > dividers and corresponding control registers mapped to different
> > addresses.
> > So we add one common driver for such PLLs.
> > 
> > Each PLL on AXS10X board consist of three dividers: IDIV, FBDIV and
> > ODIV. Output clock value is managed using these dividers.
> > 
> > We add pre-defined tables with supported rate values and
> > appropriate
> > configurations of IDIV, FBDIV and ODIV for each value.
> > 
> > As of today we add support for PLLs that generate clock for the
> > following devices:
> >  * ARC core on AXC CPU tiles.
> >  * ARC PGU on ARC SDP Mainboard.
> > and more to come later.
> > 
> > By this patch we add support for two plls (arc core pll and pgu
> > pll),
> > so we had to use two different init types: CLK_OF_DECLARE for arc
> > core pll and
> > regular probing for pgu pll.
> > 
> > Acked-by: Rob Herring <robh at kernel.org>
> > Acked-by: Jose Abreu <joabreu at synopsys.com>
> > 
> > Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev at synopsys.com>
> > Signed-off-by: Vlad Zakharov <vzakhar at synopsys.com>
> > Signed-off-by: Jose Abreu <joabreu at synopsys.com>
> 
> Sorry this missed the cutoff for new code for v4.13. Should be in
> clk-next next week though.
> 
> > +}
> > +
> > +static inline struct axs10x_pll_clk *to_axs10x_pll_clk(struct
> > clk_hw *hw)
> > +{
> > +	return container_of(hw, struct axs10x_pll_clk, hw);
> > +}
> > +
> > +static inline u32 axs10x_div_get_value(u32 reg)
> > +{
> > +	if (PLL_REG_GET_BYPASS(reg))
> > +		return 1;
> > +
> > +	return PLL_REG_GET_HIGH(reg) + PLL_REG_GET_LOW(reg);
> > +}
> > +
> > +static inline u32 axs10x_encode_div(unsigned int id, int upd)
> > +{
> > +	u32 div = 0;
> > +
> > +	PLL_REG_SET_LOW(div, (id % 2 == 0) ? id >> 1 : (id >> 1) +
> > 1);
> > +	PLL_REG_SET_HIGH(div, id >> 1);
> > +	PLL_REG_SET_EDGE(div, id % 2);
> > +	PLL_REG_SET_BYPASS(div, id == 1 ? 1 : 0);
> > +	PLL_REG_SET_NOUPD(div, !upd);
> 
> So sparse complains here about a "dubious !x & y". Perhaps this
> can be changed to
> 
> 	PLL_REG_SET_NOUPD(div, upd == 0 ? 1 : 0);
> 
> That way sparse doesn't complain. I can make the change when
> applying if you agree.

Sure, thanks a lot.

-- 
 Eugeniy Paltsev