[PATCH 2/3 v2] ASoC: dwc: Add I2S HDMI audio support

Alexey Brodkin Alexey.Brodkin at synopsys.com
Mon Mar 28 08:35:46 PDT 2016


Hi Jose,

On Mon, 2016-03-28 at 15:36 +0100, Jose Abreu wrote:
> HDMI audio support was added to the AXS board using an
> I2S cpu driver and a custom platform driver.
> 
> The platform driver supports two channels @ 16 bits with
> rates 32k, 44.1k and 48k. ALSA Simple audio card is used to
> glue the cpu, platform and codec driver (adv7511).
> 
> Signed-off-by: Jose Abreu <joabreu at synopsys.com>
> ---
> 
> No changes v1 -> v2.
> 
>  sound/soc/dwc/Kconfig          |   1 +
>  sound/soc/dwc/designware_i2s.c | 385 +++++++++++++++++++++++++++++++++++++++--
>  2 files changed, 373 insertions(+), 13 deletions(-)
> 
> diff --git a/sound/soc/dwc/Kconfig b/sound/soc/dwc/Kconfig
> index d50e085..bc3fae7 100644
> --- a/sound/soc/dwc/Kconfig
> +++ b/sound/soc/dwc/Kconfig
> @@ -2,6 +2,7 @@ config SND_DESIGNWARE_I2S
>  	tristate "Synopsys I2S Device Driver"
>  	depends on CLKDEV_LOOKUP
>  	select SND_SOC_GENERIC_DMAENGINE_PCM
> +	select SND_SIMPLE_CARD
>  	help
>  	 Say Y or M if you want to add support for I2S driver for
>  	 Synopsys desigwnware I2S device. The device supports upto
> diff --git a/sound/soc/dwc/designware_i2s.c b/sound/soc/dwc/designware_i2s.c
> index bff258d..0f2f588 100644
> --- a/sound/soc/dwc/designware_i2s.c
> +++ b/sound/soc/dwc/designware_i2s.c
> @@ -84,11 +84,37 @@
>  #define MAX_CHANNEL_NUM		8
>  #define MIN_CHANNEL_NUM		2
>  
> +/* FPGA Version Info */
> +#define FPGA_VER_INFO	0xE0011230
> +#define FPGA_VER_27M	0x000FBED9
> +
> +/* PLL registers addresses */
> +#define PLL_IDIV_ADDR	0xE00100A0
> +#define PLL_FBDIV_ADDR	0xE00100A4
> +#define PLL_ODIV0_ADDR	0xE00100A8
> +#define PLL_ODIV1_ADDR	0xE00100AC

Well I think all is not acceptable.
See all these FPGA_VER_xxx as well as PLL_xxx
are strictly ARC SDP specific things and have nothing to do with generic driver.

That's so pity we don't have a driver for all clocks/PLLs on ARC SDP yet.
So as of now I may only propose to use hard-coded fixed clocks as I did with
ARC PGU, see "pguclk" here:
http://lists.infradead.org/pipermail/linux-snps-arc/2016-March/000790.html

Again I'll try to implement missing clock driver sometime soon because
more and more stuff requires it but for now let's use a work-around.

> +struct dw_i2s_pll {
> +	unsigned int rate;
> +	unsigned int data_width;
> +	unsigned int idiv;
> +	unsigned int fbdiv;
> +	unsigned int odiv0;
> +	unsigned int odiv1;
> +};
> +
> +static const struct dw_i2s_pll dw_i2s_pll_cfg_27m[] = {
> +	/* 27Mhz */
> +	{ 32000, 16, 0x104, 0x451, 0x10E38, 0x2000 },
> +	{ 44100, 16, 0x104, 0x596, 0x10D35, 0x2000 },
> +	{ 48000, 16, 0x208, 0xA28, 0x10B2C, 0x2000 },
> +	{ 0, 0, 0, 0, 0, 0 },
>  };
>  
> +static const struct dw_i2s_pll dw_i2s_pll_cfg_28m[] = {
> +	/* 28.224Mhz */
> +	{ 32000, 16, 0x82, 0x105, 0x107DF, 0x2000 },
> +	{ 44100, 16, 0x28A, 0x1, 0x10001, 0x2000 },
> +	{ 48000, 16, 0xA28, 0x187, 0x10042, 0x2000 },
> +	{ 0, 0, 0, 0, 0, 0 },
> +};

These 2 hunks as well should go in ARC SDP clocks.

> +static int i2s_pll_cfg(struct i2s_clk_config_data *config)
> +{
> +	const struct dw_i2s_pll *pll_cfg;
> +	u32 rate = config->sample_rate;
> +	u32 data_width = config->data_width;
> +	int i;
> +
> +	if (readl((void *)FPGA_VER_INFO) <= FPGA_VER_27M)
> +		pll_cfg = dw_i2s_pll_cfg_27m;
> +	else
> +		pll_cfg = dw_i2s_pll_cfg_28m;
> +
> +	for (i = 0; pll_cfg[i].rate != 0; i++) {
> +		if ((pll_cfg[i].rate == rate) &&
> +				(pll_cfg[i].data_width == data_width)) {
> +			writel(pll_cfg[i].idiv, (void *)PLL_IDIV_ADDR);
> +			writel(pll_cfg[i].fbdiv, (void *)PLL_FBDIV_ADDR);
> +			writel(pll_cfg[i].odiv0, (void *)PLL_ODIV0_ADDR);
> +			writel(pll_cfg[i].odiv1, (void *)PLL_ODIV1_ADDR);
> +			return 0;
> +		}
> +	}
> +
> +	return -EINVAL;
> +}

Ditto.

-Alexey


More information about the linux-snps-arc mailing list