[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083]
[    0.000000] Linux version 6.15.0-rc6-00001-ge00d83a22d25-dirty (linux@devel) (aarch64-unknown-linux-gnu-gcc (Gentoo Hardened 14.2.1_p20250301 p8) 14.2.1 20250301, GNU ld (Gentoo 2.44 p1) 2.44.0) #4 SMP PREEMPT Thu May 15 09:14:14 GMT 2025
[    0.000000] KASLR enabled
[    0.000000] random: crng init done
[    0.000000] Machine model: Raspberry Pi 4 Model B Rev 1.5
[    0.000000] earlycon: uart8250 at MMIO32 0x00000000fe215040 (options '')
[    0.000000] printk: legacy bootconsole [uart8250] enabled
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000037200000, size 64 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[    0.000000] OF: reserved mem: 0x0000000037200000..0x000000003b1fffff (65536 KiB) map reusable linux,cma
[    0.000000] OF: reserved mem: 0x000000003ee66540..0x000000003ee66575 (0 KiB) nomap non-reusable nvram@0
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000000000-0x000000003fffffff]
[    0.000000]   DMA32    [mem 0x0000000040000000-0x00000000fbffffff]
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x000000003b2fffff]
[    0.000000]   node   0: [mem 0x0000000040000000-0x00000000fbffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000000fbffffff]
[    0.000000] On node 0, zone DMA32: 19712 pages in unavailable ranges
[    0.000000] On node 0, zone DMA32: 16384 pages in unavailable ranges
[    0.000000] percpu: Embedded 39 pages/cpu s43608 r0 d116136 u159744
[    0.000000] pcpu-alloc: s43608 r0 d116136 u159744 alloc=39*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
[    0.000000] Detected PIPT I-cache on CPU0
[    0.000000] CPU features: detected: Spectre-v2
[    0.000000] CPU features: detected: Spectre-v3a
[    0.000000] CPU features: detected: Spectre-v4
[    0.000000] CPU features: detected: Spectre-BHB
[    0.000000] CPU features: kernel page table isolation forced ON by KASLR
[    0.000000] CPU features: detected: Kernel page table isolation (KPTI)
[    0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[    0.000000] alternatives: applying boot alternatives
[    0.000000] Kernel command line:  dma.dmachans=0x37f5 bcm2709.boardrev=0xc03115 bcm2709.serial=0x8d497109 bcm2709.uart_clock=48000000 bcm2709.disk_led_gpio=42 bcm2709.disk_led_active_low=0 smsc95xx.macaddr=D8:3A:DD:35:83:0A vc_mem.mem_base=0x3eb00000 vc_mem.mem_size=0x3ff00000  ro root=PARTUUID=3c197eda-aad8-44ce-84bb-90219551e20d earlycon=uart8250,mmio32,0xfe215040  rootwait loglevel=8 dyndbg="file drivers/gpu/* +p" vc4.force_hotplug=1
[    0.000000] printk: log buffer data + meta data: 131072 + 458752 = 589824 bytes
[    0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[    0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[    0.000000] software IO TLB: area num 4.
[    0.000000] software IO TLB: mapped [mem 0x0000000033200000-0x0000000037200000] (64MB)
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 1012480
[    0.000000] mem auto-init: stack:all(zero), heap alloc:on, heap free:off
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] Root IRQ handler: gic_handle_irq
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] arch_timer: cp15 timer(s) running at 54.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xc743ce346, max_idle_ns: 440795203123 ns
[    0.000000] sched_clock: 56 bits at 54MHz, resolution 18ns, wraps every 4398046511102ns
[    0.008344] Console: colour dummy device 80x25
[    0.012838] printk: legacy console [tty0] enabled
[    0.017592] printk: legacy bootconsole [uart8250] disabled
[    0.023162] Calibrating delay loop (skipped), value calculated using timer frequency.. 108.50 BogoMIPS (lpj=180000)
[    0.023177] pid_max: default: 32768 minimum: 301
[    0.023450] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.023484] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.030004] rcu: Hierarchical SRCU implementation.
[    0.030022] rcu: 	Max phase no-delay instances is 1000.
[    0.030214] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level
[    0.031424] smp: Bringing up secondary CPUs ...
[    0.031730] Detected PIPT I-cache on CPU1
[    0.031804] CPU1: Booted secondary processor 0x0000000001 [0x410fd083]
[    0.032122] Detected PIPT I-cache on CPU2
[    0.032160] CPU2: Booted secondary processor 0x0000000002 [0x410fd083]
[    0.032454] Detected PIPT I-cache on CPU3
[    0.032493] CPU3: Booted secondary processor 0x0000000003 [0x410fd083]
[    0.032539] smp: Brought up 1 node, 4 CPUs
[    0.032567] SMP: Total of 4 processors activated.
[    0.032572] CPU: All CPU(s) started at EL2
[    0.032577] CPU features: detected: 32-bit EL0 Support
[    0.032583] CPU features: detected: CRC32 instructions
[    0.032595] CPU features: detected: PMUv3
[    0.032626] alternatives: applying system-wide alternatives
[    0.032890] Memory: 3814420K/4049920K available (12864K kernel code, 1268K rwdata, 3268K rodata, 1152K init, 360K bss, 165976K reserved, 65536K cma-reserved)
[    0.033638] devtmpfs: initialized
[    0.037674] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    0.037725] posixtimers hash table entries: 2048 (order: 3, 32768 bytes, linear)
[    0.037787] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.038790] pinctrl core: initialized pinctrl subsystem
[    0.039579] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.040907] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations
[    0.041176] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.041638] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.041932] thermal_sys: Registered thermal governor 'step_wise'
[    0.041937] thermal_sys: Registered thermal governor 'power_allocator'
[    0.041973] cpuidle: using governor ladder
[    0.041996] cpuidle: using governor menu
[    0.042066] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.042118] ASID allocator initialised with 32768 entries
[    0.042221] Serial: AMBA PL011 UART driver
[    0.045041] /soc/interrupt-controller@40041000: Fixed dependency cycle(s) with /soc/interrupt-controller@40041000
[    0.049002] /scb/pcie@7d500000: Fixed dependency cycle(s) with /scb/pcie@7d500000
[    0.049188] /scb/pcie@7d500000: Fixed dependency cycle(s) with /scb/pcie@7d500000
[    0.052252] iommu: Default domain type: Translated
[    0.052284] iommu: DMA domain TLB invalidation policy: strict mode
[    0.052888] SCSI subsystem initialized
[    0.053012] usbcore: registered new interface driver usbfs
[    0.053039] usbcore: registered new interface driver hub
[    0.053068] usbcore: registered new device driver usb
[    0.053236] usb_phy_generic phy: dummy supplies not allowed for exclusive requests (id=vbus)
[    0.053460] pps_core: LinuxPPS API ver. 1 registered
[    0.053468] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.053861] Advanced Linux Sound Architecture Driver Initialized.
[    0.054401] Bluetooth: Core ver 2.22
[    0.054424] NET: Registered PF_BLUETOOTH protocol family
[    0.054432] Bluetooth: HCI device and connection manager initialized
[    0.054442] Bluetooth: HCI socket layer initialized
[    0.054450] Bluetooth: L2CAP socket layer initialized
[    0.054462] Bluetooth: SCO socket layer initialized
[    0.054631] vgaarb: loaded
[    0.054849] clocksource: Switched to clocksource arch_sys_counter
[    0.059222] NET: Registered PF_INET protocol family
[    0.059543] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.061496] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
[    0.061683] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.061801] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.062267] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear)
[    0.063245] TCP: Hash tables configured (established 32768 bind 32768)
[    0.063448] UDP hash table entries: 2048 (order: 5, 131072 bytes, linear)
[    0.063743] UDP-Lite hash table entries: 2048 (order: 5, 131072 bytes, linear)
[    0.064141] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.064929] PCI: CLS 0 bytes, default 64
[    0.065698] Initialise system trusted keyrings
[    0.065818] workingset: timestamp_bits=62 max_order=20 bucket_order=0
[    0.066324] fuse: init (API version 7.43)
[    0.097230] Key type asymmetric registered
[    0.097240] Asymmetric key parser 'x509' registered
[    0.097422] io scheduler mq-deadline registered
[    0.097432] io scheduler kyber registered
[    0.097889] irq_brcmstb_l2: registered L2 intc (/soc/interrupt-controller@7ef00100, parent irq: 14)
[    0.099140] pinctrl-bcm2835 fe200000.gpio: GPIO_OUT persistence: no
[    0.100321] brcm-pcie fd500000.pcie: host bridge /scb/pcie@7d500000 ranges:
[    0.100350] brcm-pcie fd500000.pcie:      MEM 0x0600000000..0x0603ffffff -> 0x00f8000000
[    0.100373] brcm-pcie fd500000.pcie:   IB MEM 0x0000000000..0x00ffffffff -> 0x0400000000
[    0.101090] brcm-pcie fd500000.pcie: PCI host bridge to bus 0000:00
[    0.101106] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.101119] pci_bus 0000:00: root bus resource [mem 0x600000000-0x603ffffff] (bus address [0xf8000000-0xfbffffff])
[    0.101197] pci 0000:00:00.0: [14e4:2711] type 01 class 0x060400 PCIe Root Port
[    0.101218] pci 0000:00:00.0: PCI bridge to [bus 00]
[    0.101229] pci 0000:00:00.0:   bridge window [mem 0x600000000-0x6000fffff]
[    0.101273] pci 0000:00:00.0: PME# supported from D0 D3hot
[    0.102434] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    0.102504] pci_bus 0000:01: supply vpcie3v3 not found, using dummy regulator
[    0.102592] pci_bus 0000:01: supply vpcie3v3aux not found, using dummy regulator
[    0.102621] pci_bus 0000:01: supply vpcie12v not found, using dummy regulator
[    0.204860] brcm-pcie fd500000.pcie: clkreq-mode set to default
[    0.206923] brcm-pcie fd500000.pcie: link up, 5.0 GT/s PCIe x1 (SSC)
[    0.207054] pci 0000:01:00.0: [1106:3483] type 00 class 0x0c0330 PCIe Endpoint
[    0.207143] pci 0000:01:00.0: BAR 0 [mem 0x00000000-0x00000fff 64bit]
[    0.207260] pci 0000:01:00.0: PME# supported from D0 D3hot
[    0.211574] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    0.211606] pci 0000:00:00.0: bridge window [mem 0x600000000-0x6000fffff]: assigned
[    0.211619] pci 0000:01:00.0: BAR 0 [mem 0x600000000-0x600000fff 64bit]: assigned
[    0.211667] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.211676] pci 0000:00:00.0:   bridge window [mem 0x600000000-0x6000fffff]
[    0.211688] pci_bus 0000:00: resource 4 [mem 0x600000000-0x603ffffff]
[    0.211696] pci_bus 0000:01: resource 1 [mem 0x600000000-0x6000fffff]
[    0.211811] pcieport 0000:00:00.0: enabling device (0000 -> 0002)
[    0.211895] pcieport 0000:00:00.0: PME: Signaling with IRQ 19
[    0.212087] pcieport 0000:00:00.0: AER: enabled with IRQ 19
[    0.212588] simple-framebuffer 3e40f000.framebuffer: framebuffer at 0x3e40f000, 0x6e7000 bytes
[    0.212602] simple-framebuffer 3e40f000.framebuffer: format=a8r8g8b8, mode=1824x984x32, linelength=7296
[    0.212843] Console: do_bind_con_driver, backtrace:
[    0.212849] CPU: 2 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.15.0-rc6-00001-ge00d83a22d25-dirty #4 PREEMPT 
[    0.212858] Hardware name: Raspberry Pi 4 Model B Rev 1.5 (DT)
[    0.212861] Call trace:
[    0.212863]  show_stack+0x2c/0xc0 (C)
[    0.212874]  dump_stack_lvl+0x60/0x94
[    0.212881]  dump_stack+0x18/0x30
[    0.212885]  do_bind_con_driver.isra.0+0x40/0x294
[    0.212894]  do_take_over_console+0x128/0x1c4
[    0.212903]  do_fbcon_takeover+0x6c/0x108
[    0.212908]  fbcon_fb_registered+0x1d4/0x1e0
[    0.212914]  do_register_framebuffer+0x1a4/0x278
[    0.212923]  register_framebuffer+0x2c/0x60
[    0.212929]  simplefb_probe+0x83c/0x974
[    0.212934]  platform_probe+0x68/0xf0
[    0.212941]  really_probe+0xc0/0x3ac
[    0.212946]  __driver_probe_device+0x7c/0x174
[    0.212951]  driver_probe_device+0x40/0x100
[    0.212955]  __driver_attach+0xa8/0x284
[    0.212960]  bus_for_each_dev+0x7c/0xfc
[    0.212964]  driver_attach+0x24/0x44
[    0.212968]  bus_add_driver+0x170/0x298
[    0.212972]  driver_register+0x68/0x160
[    0.212976]  __platform_driver_register+0x24/0x44
[    0.212982]  simplefb_driver_init+0x1c/0x34
[    0.212990]  do_one_initcall+0x80/0x180
[    0.212996]  kernel_init_freeable+0x1ac/0x230
[    0.213001]  kernel_init+0x20/0x140
[    0.213008]  ret_from_fork+0x10/0x20
[    0.216052] Console: switching to colour frame buffer device 228x61
[    0.219399] simple-framebuffer 3e40f000.framebuffer: fb0: simplefb registered!
[    0.222096] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.223243] fe215040.serial: ttyS1 at MMIO 0xfe215040 (irq = 27, base_baud = 62499999) is a 16550
[    0.223314] printk: legacy console [ttyS1] enabled
[    1.457149] iproc-rng200 fe104000.rng: hwrng registered
[    1.464206] loop: module loaded
[    1.467175] bcm2835-power bcm2835-power: Broadcom BCM2835 power domains driver
[    1.475554] SSFDC read-only Flash Translation layer
[    1.481166] slram: not enough parameters.
[    1.487027] bcmgenet fd580000.ethernet: GENET 5.0 EPHY: 0x0000
[    1.704961] unimac-mdio unimac-mdio.-19: Broadcom UniMAC MDIO bus
[    1.712176] usbcore: registered new interface driver brcmfmac
[    1.719112] usbcore: registered new interface driver uas
[    1.724831] usbcore: registered new interface driver usb-storage
[    1.731377] usbcore: registered new interface driver usbserial_generic
[    1.738358] usbserial: USB Serial support registered for generic
[    1.744986] mousedev: PS/2 mouse device common for all mice
[    1.751026] i2c_dev: i2c /dev entries driver
[    1.756590] brcmstb-i2c fef04500.i2c:  @97500hz registered in polling mode
[    1.764085] brcmstb-i2c fef09500.i2c:  @97500hz registered in polling mode
[    1.771666] i2c i2c-0: Added multiplexed i2c bus 4
[    1.776957] i2c i2c-0: Added multiplexed i2c bus 5
[    1.782167] pps_ldisc: PPS line discipline registered
[    1.788653] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer
[    1.795518] Bluetooth: HCI UART driver ver 2.3
[    1.800349] Bluetooth: HCI UART protocol H4 registered
[    1.805912] Bluetooth: HCI UART protocol Three-wire (H5) registered
[    1.812622] Bluetooth: HCI UART protocol Broadcom registered
[    1.819070] sdhci: Secure Digital Host Controller Interface driver
[    1.825607] sdhci: Copyright(c) Pierre Ossman
[    1.830371] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.836650] hid: raw HID events driver (C) Jiri Kosina
[    1.842178] usbcore: registered new interface driver usbhid
[    1.848118] usbhid: USB HID core driver
[    1.852749] bcm2835-mbox fe00b880.mailbox: mailbox enabled
[    1.859438] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 (0,8000003f) counters available
[    1.870784] NET: Registered PF_INET6 protocol family
[    1.876872] Segment Routing with IPv6
[    1.880983] In-situ OAM (IOAM) with IPv6
[    1.885400] NET: Registered PF_PACKET protocol family
[    1.894442] Loading compiled-in X.509 certificates
[    1.914021] fe201000.serial: ttyAMA0 at MMIO 0xfe201000 (irq = 37, base_baud = 0) is a PL011 rev3
[    1.924374] raspberrypi-firmware soc:firmware: Attached to firmware from 2025-02-17T20:03:07
[    1.934135] uart-pl011 fe201000.serial: Failed to create device link (0x180) with supplier soc:firmware:gpio for /soc/serial@7e201000/bluetooth
[    1.959181] v3d fec00000.gpu: [drm] Using Transparent Hugepages
[    1.966543] [drm] Initialized v3d 1.0.0 for fec00000.gpu on minor 0
[    1.974165] Console: do_bind_con_driver, backtrace:
[    1.974174] CPU: 3 UID: 0 PID: 42 Comm: kworker/u16:1 Not tainted 6.15.0-rc6-00001-ge00d83a22d25-dirty #4 PREEMPT 
[    1.974183] Hardware name: Raspberry Pi 4 Model B Rev 1.5 (DT)
[    1.974186] Workqueue: events_unbound deferred_probe_work_func
[    1.974200] Call trace:
[    1.974203]  show_stack+0x2c/0xc0 (C)
[    1.974211]  dump_stack_lvl+0x60/0x94
[    1.974218]  dump_stack+0x18/0x30
[    1.974223]  do_bind_con_driver.isra.0+0x40/0x294
[    1.974232]  do_unbind_con_driver+0x1b8/0x1dc
[    1.974241]  fbcon_fb_unbind+0x108/0x1d8
[    1.974247]  unregister_framebuffer+0x110/0x120
[    1.974256]  simplefb_remove+0x14/0x2c
[    1.974261]  platform_remove+0x28/0x5c
[    1.974267]  device_remove+0x4c/0xa0
[    1.974272]  device_release_driver_internal+0x1fc/0x250
[    1.974277]  device_release_driver+0x18/0x40
[    1.974282]  bus_remove_device+0xd4/0x17c
[    1.974286]  device_del+0x150/0x3b8
[    1.974293]  platform_device_del+0x28/0xbc
[    1.974299]  platform_device_unregister+0x18/0x50
[    1.974304]  aperture_detach_platform_device+0x14/0x2c
[    1.974310]  aperture_detach_devices+0xb8/0x120
[    1.974315]  aperture_remove_conflicting_devices+0x10/0x2c
[    1.974321]  vc4_drm_bind+0x110/0x364
[    1.974327]  try_to_bring_up_aggregate_device+0x22c/0x308
[    1.974333]  __component_add+0xec/0x224
[    1.974337]  component_add+0x14/0x30
[    1.974342]  vc4_hdmi_dev_probe+0x1c/0x40
[    1.974349]  platform_probe+0x68/0xf0
[    1.974355]  really_probe+0xc0/0x3ac
[    1.974359]  __driver_probe_device+0x7c/0x174
[    1.974364]  driver_probe_device+0x40/0x100
[    1.974369]  __device_attach_driver+0x10c/0x1e0
[    1.974374]  bus_for_each_drv+0x88/0x100
[    1.974378]  __device_attach+0xa0/0x1c8
[    1.974382]  device_initial_probe+0x14/0x30
[    1.974387]  bus_probe_device+0xc8/0xcc
[    1.974391]  deferred_probe_work_func+0xb8/0x12c
[    1.974396]  process_one_work+0x160/0x2d4
[    1.974402]  worker_thread+0x2d8/0x400
[    1.974407]  kthread+0x12c/0x208
[    1.974412]  ret_from_fork+0x10/0x20
[    1.974465] Console: switching to colour dummy device 80x25
[    3.117669] vc4-drm gpu: bound fe400000.hvs (ops 0xffffffec3652f480)
[    3.124550] Registered IR keymap rc-cec
[    3.127969] rc rc0: vc4-hdmi-0 as /devices/platform/soc/fef00700.hdmi/rc/rc0
[    3.135095] input: vc4-hdmi-0 as /devices/platform/soc/fef00700.hdmi/rc/rc0/input0
[    3.143782] vc4-drm gpu: bound fef00700.hdmi (ops 0xffffffec3652bc68)
[    3.150739] Registered IR keymap rc-cec
[    3.154126] rc rc1: vc4-hdmi-1 as /devices/platform/soc/fef05700.hdmi/rc/rc1
[    3.161277] input: vc4-hdmi-1 as /devices/platform/soc/fef05700.hdmi/rc/rc1/input1
[    3.170511] vc4-drm gpu: bound fef05700.hdmi (ops 0xffffffec3652bc68)
[    3.176635] vc4-drm gpu: bound fe004000.txp (ops 0xffffffec365307d0)
[    3.183020] vc4-drm gpu: bound fe206000.pixelvalve (ops 0xffffffec365296f0)
[    3.190021] vc4-drm gpu: bound fe207000.pixelvalve (ops 0xffffffec365296f0)
[    3.197078] vc4-drm gpu: bound fe20a000.pixelvalve (ops 0xffffffec365296f0)
[    3.204093] vc4-drm gpu: bound fe216000.pixelvalve (ops 0xffffffec365296f0)
[    3.212190] [drm] Initialized vc4 0.0.0 for gpu on minor 1
[    3.242874] dwc2 fe980000.usb: supply vusb_d not found, using dummy regulator
[    3.249618] dwc2 fe980000.usb: supply vusb_a not found, using dummy regulator
[    3.256814] dwc2 fe980000.usb: Configuration mismatch. dr_mode forced to host
[    3.314498] dwc2 fe980000.usb: DWC OTG Controller
[    3.318697] dwc2 fe980000.usb: new USB bus registered, assigned bus number 1
[    3.325831] dwc2 fe980000.usb: irq 52, io mem 0xfe980000
[    3.331345] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.15
[    3.339573] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.346888] usb usb1: Product: DWC OTG Controller
[    3.351653] usb usb1: Manufacturer: Linux 6.15.0-rc6-00001-ge00d83a22d25-dirty dwc2_hsotg
[    3.359924] usb usb1: SerialNumber: fe980000.usb
[    3.364884] hub 1-0:1.0: USB hub found
[    3.368409] hub 1-0:1.0: 1 port detected
[    3.417774] xhci_hcd 0000:01:00.0: xHCI Host Controller
[    3.422496] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[    3.430742] xhci_hcd 0000:01:00.0: hcc params 0x002841eb hci version 0x100 quirks 0x0000200000000890
[    3.439978] xhci_hcd 0000:01:00.0: xHCI Host Controller
[    3.444716] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3
[    3.452208] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed
[    3.458656] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.15
[    3.466922] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.474233] usb usb2: Product: xHCI Host Controller
[    3.479168] usb usb2: Manufacturer: Linux 6.15.0-rc6-00001-ge00d83a22d25-dirty xhci-hcd
[    3.487273] usb usb2: SerialNumber: 0000:01:00.0
[    3.492202] hub 2-0:1.0: USB hub found
[    3.495780] hub 2-0:1.0: 1 port detected
[    3.500025] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.15
[    3.508073] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.515385] usb usb3: Product: xHCI Host Controller
[    3.520320] usb usb3: Manufacturer: Linux 6.15.0-rc6-00001-ge00d83a22d25-dirty xhci-hcd
[    3.528473] usb usb3: SerialNumber: 0000:01:00.0
[    3.533369] hub 3-0:1.0: USB hub found
[    3.536933] hub 3-0:1.0: 4 ports detected
[    3.543472] sdhci-iproc fe300000.mmc: allocated mmc-pwrseq
[    3.551814] bcm2835-audio bcm2835-audio: card created with 8 channels
[    3.558562] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    3.566422] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    3.571921] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600'
[    3.578204] mmc0: SDHCI controller on fe300000.mmc [fe300000.mmc] using PIO
[    3.578971] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    3.581536] clk: Disabling unused clocks
[    3.581683] PM: genpd: Disabling unused power domains
[    3.581711] ALSA device list:
[    3.581714]   #0: vc4-hdmi-0
[    3.581718]   #1: vc4-hdmi-1
[    3.581721]   #2: bcm2835 Headphones
[    3.597243] mmc0: Controller never released inhibit bit(s).
[    3.598631] cfg80211: failed to load regulatory.db
[    3.600766] mmc1: SDHCI controller on fe340000.mmc [fe340000.mmc] using ADMA
[    3.603736] mmc0: sdhci: ============ SDHCI REGISTER DUMP ===========
[    3.603739] mmc0: sdhci: Sys addr:  0x00000000 | Version:  0x00009902
[    3.646852] mmc0: sdhci: Blk size:  0x00000000 | Blk cnt:  0x00000000
[    3.646856] mmc0: sdhci: Argument:  0x00000000 | Trn mode: 0x00000000
[    3.646859] mmc0: sdhci: Present:   0x01ff0001 | Host ctl: 0x00000000
[    3.665697] mmc0: sdhci: Power:     0x0000000f | Blk gap:  0x00000000
[    3.672214] mmc0: sdhci: Wake-up:   0x00000000 | Clock:    0x00003947
[    3.678736] mmc0: sdhci: Timeout:   0x00000000 | Int stat: 0x00000000
[    3.678760] Waiting for root device PARTUUID=3c197eda-aad8-44ce-84bb-90219551e20d...
[    3.685254] mmc0: sdhci: Int enab:  0x00ff0003 | Sig enab: 0x00ff0003
[    3.685257] mmc0: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00000000
[    3.685260] mmc0: sdhci: Caps:      0x00000000 | Caps_1:   0x00000000
[    3.712672] mmc0: sdhci: Cmd:       0x00000000 | Max curr: 0x00000001
[    3.719186] mmc0: sdhci: Resp[0]:   0x00000000 | Resp[1]:  0x00000000
[    3.725708] mmc0: sdhci: Resp[2]:   0x00000000 | Resp[3]:  0x00000000
[    3.732230] mmc0: sdhci: Host ctl2: 0x00000000
[    3.736724] mmc0: sdhci: ============================================
[    3.819205] mmc0: new high speed SDIO card at address 0001
[    3.826890] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[    3.835205] brcmfmac mmc0:0001:1: Direct firmware load for brcm/brcmfmac43455-sdio.raspberrypi,4-model-b.bin failed with error -2
[    3.846904] brcmfmac mmc0:0001:1: Direct firmware load for brcm/brcmfmac43455-sdio.bin failed with error -2
[    3.858194] usb 2-1: new high-speed USB device number 2 using xhci_hcd
[    3.994065] usb 2-1: New USB device found, idVendor=2109, idProduct=3431, bcdDevice= 4.21
[    4.001786] usb 2-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    4.009001] usb 2-1: Product: USB2.0 Hub
[    4.014147] hub 2-1:1.0: USB hub found
[    4.017575] hub 2-1:1.0: 4 ports detected
[    4.108535] usb 3-2: new SuperSpeed USB device number 2 using xhci_hcd
[    4.131936] usb 3-2: New USB device found, idVendor=174c, idProduct=5106, bcdDevice= 0.01
[    4.139693] usb 3-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[    4.146910] usb 3-2: Product: AS2105
[    4.150495] usb 3-2: Manufacturer: ASMedia
[    4.154624] usb 3-2: SerialNumber:      WD-WCAZAC619762
[    4.161925] usb-storage 3-2:1.0: USB Mass Storage device detected
[    4.167841] scsi host0: usb-storage 3-2:1.0
[    4.318193] usb 2-1.3: new low-speed USB device number 3 using xhci_hcd
[    4.413135] usb 2-1.3: New USB device found, idVendor=046d, idProduct=c31c, bcdDevice=64.00
[    4.421023] usb 2-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    4.428430] usb 2-1.3: Product: USB Keyboard
[    4.432743] usb 2-1.3: Manufacturer: Logitech
[    4.446750] input: Logitech USB Keyboard as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb2/2-1/2-1.3/2-1.3:1.0/0003:046D:C31C.0001/input/input2
[    4.515142] hid-generic 0003:046D:C31C.0001: input,hidraw0: USB HID v1.10 Keyboard [Logitech USB Keyboard] on usb-0000:01:00.0-1.3/input0
[    4.537567] input: Logitech USB Keyboard Consumer Control as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb2/2-1/2-1.3/2-1.3:1.1/0003:046D:C31C.0002/input/input3
[    4.604975] input: Logitech USB Keyboard System Control as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb2/2-1/2-1.3/2-1.3:1.1/0003:046D:C31C.0002/input/input4
[    4.621651] hid-generic 0003:046D:C31C.0002: input,hidraw1: USB HID v1.10 Device [Logitech USB Keyboard] on usb-0000:01:00.0-1.3/input1
[    4.698192] usb 2-1.4: new low-speed USB device number 4 using xhci_hcd
[    4.792944] usb 2-1.4: New USB device found, idVendor=046d, idProduct=c05a, bcdDevice=63.00
[    4.800833] usb 2-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    4.808240] usb 2-1.4: Product: USB Optical Mouse
[    4.812993] usb 2-1.4: Manufacturer: Logitech
[    4.823051] input: Logitech USB Optical Mouse as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb2/2-1/2-1.4/2-1.4:1.0/0003:046D:C05A.0003/input/input5
[    4.838915] hid-generic 0003:046D:C05A.0003: input,hidraw2: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:01:00.0-1.4/input0
[    4.858207] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50
[    5.181936] scsi 0:0:0:0: Direct-Access     WDC WD20 EARX-00PASB0     51.0 PQ: 0 ANSI: 5
[    5.190221] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[    5.198002] sd 0:0:0:0: [sda] Write Protect is off
[    5.202338] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
[    5.207960] sd 0:0:0:0: [sda] No Caching mode page found
[    5.212823] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    5.275803]  sda: sda1 sda2 sda3
[    5.278758] sd 0:0:0:0: [sda] Attached SCSI disk
[    5.344704] EXT4-fs (sda2): mounted filesystem d8b40bd2-f780-41e2-b982-2effe38beed1 ro with ordered data mode. Quota mode: disabled.
[    5.356264] VFS: Mounted root (ext4 filesystem) readonly on device 8:2.
[    5.363540] Freeing unused kernel memory: 1152K
[    5.367674] Run /sbin/init as init process
[    5.371705]   with arguments:
[    5.374676]     /sbin/init
[    5.377445]   with environment:
[    5.380587]     HOME=/
[    5.382965]     TERM=linux
[    8.524347] bcmgenet fd580000.ethernet outbr: renamed from eth0
[    9.471940] EXT4-fs (sda2): re-mounted d8b40bd2-f780-41e2-b982-2effe38beed1 r/w.
[    9.528221] EXT4-fs (sda2): re-mounted d8b40bd2-f780-41e2-b982-2effe38beed1.
[    9.945707] EXT4-fs (sda3): mounted filesystem 5f33f0cb-4bc3-44de-9f59-2ab2d626dabe r/w with ordered data mode. Quota mode: disabled.
[   12.321771] EDID: block_status_print, backtrace:
[   12.321790] CPU: 2 UID: 0 PID: 71 Comm: irq/40-vc4 hdmi Not tainted 6.15.0-rc6-00001-ge00d83a22d25-dirty #4 PREEMPT 
[   12.321802] Hardware name: Raspberry Pi 4 Model B Rev 1.5 (DT)
[   12.321805] Call trace:
[   12.321808]  show_stack+0x2c/0xc0 (C)
[   12.321820]  dump_stack_lvl+0x60/0x94
[   12.321827]  dump_stack+0x18/0x30
[   12.321832]  edid_block_status_print+0x30/0x230
[   12.321842]  _drm_do_get_edid+0x148/0x470
[   12.321851]  drm_edid_read_custom+0x34/0x100
[   12.321858]  drm_edid_read+0x54/0x108
[   12.321862]  drm_atomic_helper_connector_hdmi_update+0xac/0xe8
[   12.321868]  drm_atomic_helper_connector_hdmi_hotplug+0x10/0x38
[   12.321872]  vc4_hdmi_connector_detect_ctx+0xf4/0x2f4
[   12.321879]  detect_connector_status+0x20/0x94
[   12.321886]  drm_helper_probe_detect_ctx+0x80/0x108
[   12.321891]  check_connector_changed+0x48/0x268
[   12.321896]  drm_connector_helper_hpd_irq_event+0x30/0xdc
[   12.321901]  vc4_hdmi_hpd_irq_thread+0x38/0x54
[   12.321906]  irq_thread_fn+0x2c/0xa0
[   12.321915]  irq_thread+0x178/0x27c
[   12.321921]  kthread+0x12c/0x208
[   12.321926]  ret_from_fork+0x10/0x20
[   12.321933] EDID block 0 read ok
[   12.334322] EDID: block_status_print, backtrace:
[   12.334335] CPU: 2 UID: 0 PID: 71 Comm: irq/40-vc4 hdmi Not tainted 6.15.0-rc6-00001-ge00d83a22d25-dirty #4 PREEMPT 
[   12.334345] Hardware name: Raspberry Pi 4 Model B Rev 1.5 (DT)
[   12.334347] Call trace:
[   12.334349]  show_stack+0x2c/0xc0 (C)
[   12.334358]  dump_stack_lvl+0x60/0x94
[   12.334364]  dump_stack+0x18/0x30
[   12.334368]  edid_block_status_print+0x30/0x230
[   12.334378]  _drm_do_get_edid+0x2b4/0x470
[   12.334387]  drm_edid_read_custom+0x34/0x100
[   12.334393]  drm_edid_read+0x54/0x108
[   12.334397]  drm_atomic_helper_connector_hdmi_update+0xac/0xe8
[   12.334402]  drm_atomic_helper_connector_hdmi_hotplug+0x10/0x38
[   12.334407]  vc4_hdmi_connector_detect_ctx+0xf4/0x2f4
[   12.334413]  detect_connector_status+0x20/0x94
[   12.334418]  drm_helper_probe_detect_ctx+0x80/0x108
[   12.334423]  check_connector_changed+0x48/0x268
[   12.334428]  drm_connector_helper_hpd_irq_event+0x30/0xdc
[   12.334433]  vc4_hdmi_hpd_irq_thread+0x38/0x54
[   12.334438]  irq_thread_fn+0x2c/0xa0
[   12.334445]  irq_thread+0x178/0x27c
[   12.334451]  kthread+0x12c/0x208
[   12.334456]  ret_from_fork+0x10/0x20
[   12.334463] EDID block 1 read ok
[   13.341873] bcmgenet fd580000.ethernet: configuring instance for external RGMII (RX delay)
[   13.362530] bcmgenet fd580000.ethernet outbr: Link is Down
[   16.914964] Logdrop: IN= OUT=lo SRC=10.106.2.24 DST=10.106.2.24 LEN=104 TOS=0x10 PREC=0xC0 TTL=64 ID=36666 PROTO=ICMP TYPE=3 CODE=1 [SRC=10.106.2.24 DST=10.106.1.202 LEN=76 TOS=0x10 PREC=0x00 TTL=64 ID=10323 DF PROTO=UDP SPT=39126 DPT=123 LEN=56 ] 
[   17.421824] bcmgenet fd580000.ethernet outbr: Link is Up - 1Gbps/Full - flow control rx/tx
