[PATCH v3 4/4] ARM: dts: bcm283x: Add and use bcm2835-aux-intc

[Phil Elwell]

Add a DT node for the AUX interrupt controller, updating the AUX
peripheral nodes to make use of it.

Note that the IO region overlaps that of the AUX clock driver, but by
the time the irqchip driver appears in the tree the clock driver should
have been updated to ioremap the region without reserving it, along
with preparing for a point in the future where the clock node may be
shrunk to the single word it actually needs.

Signed-off-by: Phil Elwell <phil at raspberrypi.org>
---
 arch/arm/boot/dts/bcm283x.dtsi | 27 +++++++++++++++++++++++----
 1 file changed, 23 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index 431dcfc..b304221 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -1,6 +1,7 @@
 #include <dt-bindings/pinctrl/bcm2835.h>
 #include <dt-bindings/clock/bcm2835.h>
 #include <dt-bindings/clock/bcm2835-aux.h>
+#include <dt-bindings/interrupt-controller/bcm2835-aux-intc.h>
 #include <dt-bindings/gpio/gpio.h>
 
 /* firmware-provided startup stubs live here, where the secondary CPUs are
@@ -459,7 +460,22 @@
 			status = "disabled";
 		};
 
-		aux: aux at 0x7e215000 {
+		auxintc: interrupt-controller at 7e215000 {
+			compatible = "brcm,bcm2835-aux-intc";
+			reg = <0x7e215000 0x4>;
+			interrupts = <1 29>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		/*
+		 * N.B. This node overlaps with the previous node,
+		 * but the updated driver remaps the region without
+		 * reserving it. After a suitable period this
+		 * node can be reduced to cover only the single word
+		 * at 7e215004.
+		 */
+		aux: aux at 7e215000 {
 			compatible = "brcm,bcm2835-aux";
 			#clock-cells = <1>;
 			reg = <0x7e215000 0x8>;
@@ -469,7 +485,8 @@
 		uart1: serial at 7e215040 {
 			compatible = "brcm,bcm2835-aux-uart";
 			reg = <0x7e215040 0x40>;
-			interrupts = <1 29>;
+			interrupt-parent = <&auxintc>;
+			interrupts = <BCM2835_AUX_IRQ_UART>;
 			clocks = <&aux BCM2835_AUX_CLOCK_UART>;
 			status = "disabled";
 		};
@@ -477,7 +494,8 @@
 		spi1: spi at 7e215080 {
 			compatible = "brcm,bcm2835-aux-spi";
 			reg = <0x7e215080 0x40>;
-			interrupts = <1 29>;
+			interrupt-parent = <&auxintc>;
+			interrupts = <BCM2835_AUX_IRQ_SPI1>;
 			clocks = <&aux BCM2835_AUX_CLOCK_SPI1>;
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -487,7 +505,8 @@
 		spi2: spi at 7e2150c0 {
 			compatible = "brcm,bcm2835-aux-spi";
 			reg = <0x7e2150c0 0x40>;
-			interrupts = <1 29>;
+			interrupt-parent = <&auxintc>;
+			interrupts = <BCM2835_AUX_IRQ_SPI2>;
 			clocks = <&aux BCM2835_AUX_CLOCK_SPI2>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-- 
1.9.1