[PATCH] arm64: Add BCM2835 (Raspberry Pi 3) support to the defconfig

Eric Anholt eric at anholt.net
Mon Sep 19 06:31:50 PDT 2016


Most of the drivers are included as modules, except for serial (needed
for early console), WDT (required for reboot), and the dependency
chain of RASPBERRYPI_POWER (which is currently not buildable as a
module, but should be changed).

Signed-off-by: Eric Anholt <eric at anholt.net>
---
 arch/arm64/configs/defconfig | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index fb8d84516e92..9748c4735a60 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -34,6 +34,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_IOSCHED_DEADLINE is not set
 CONFIG_ARCH_SUNXI=y
 CONFIG_ARCH_ALPINE=y
+CONFIG_ARCH_BCM2835=y
 CONFIG_ARCH_BCM_IPROC=y
 CONFIG_ARCH_BERLIN=y
 CONFIG_ARCH_EXYNOS=y
@@ -193,6 +194,7 @@ CONFIG_USB_NET_SMSC75XX=m
 CONFIG_USB_NET_SMSC95XX=m
 CONFIG_USB_NET_PLUSB=m
 CONFIG_USB_NET_MCS7830=m
+CONFIG_BRCMFMAC=m
 CONFIG_WL18XX=m
 CONFIG_WLCORE_SDIO=m
 CONFIG_INPUT_EVDEV=y
@@ -205,6 +207,9 @@ CONFIG_SERIO_AMBAKMI=y
 CONFIG_LEGACY_PTY_COUNT=16
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_EXTENDED=y
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+CONFIG_SERIAL_8250_BCM2835AUX=y
 CONFIG_SERIAL_8250_DW=y
 CONFIG_SERIAL_8250_MT6577=y
 CONFIG_SERIAL_8250_UNIPHIER=y
@@ -228,6 +233,7 @@ CONFIG_VIRTIO_CONSOLE=y
 CONFIG_I2C_CHARDEV=y
 CONFIG_I2C_MUX=y
 CONFIG_I2C_MUX_PCA954x=y
+CONFIG_I2C_BCM2835=m
 CONFIG_I2C_DESIGNWARE_PLATFORM=y
 CONFIG_I2C_IMX=y
 CONFIG_I2C_MESON=y
@@ -238,6 +244,8 @@ CONFIG_I2C_UNIPHIER_F=y
 CONFIG_I2C_RCAR=y
 CONFIG_I2C_CROS_EC_TUNNEL=y
 CONFIG_SPI=y
+CONFIG_SPI_BCM2835=m
+CONFIG_SPI_BCM2835AUX=m
 CONFIG_SPI_MESON_SPIFC=m
 CONFIG_SPI_ORION=y
 CONFIG_SPI_PL022=y
@@ -272,6 +280,7 @@ CONFIG_THERMAL_GOV_POWER_ALLOCATOR=y
 CONFIG_CPU_THERMAL=y
 CONFIG_EXYNOS_THERMAL=y
 CONFIG_WATCHDOG=y
+CONFIG_BCM2835_WDT=y
 CONFIG_RENESAS_WDT=y
 CONFIG_S3C2410_WATCHDOG=y
 CONFIG_MESON_GXBB_WATCHDOG=m
@@ -294,6 +303,7 @@ CONFIG_REGULATOR_S2MPS11=y
 CONFIG_DRM=m
 CONFIG_DRM_NOUVEAU=m
 CONFIG_DRM_TEGRA=m
+CONFIG_DRM_VC4=m
 CONFIG_DRM_PANEL_SIMPLE=m
 CONFIG_DRM_I2C_ADV7511=m
 CONFIG_DRM_HISI_KIRIN=m
@@ -308,6 +318,7 @@ CONFIG_LOGO=y
 CONFIG_SOUND=y
 CONFIG_SND=y
 CONFIG_SND_SOC=y
+CONFIG_SND_BCM2835_SOC_I2S=m
 CONFIG_SND_SOC_RCAR=y
 CONFIG_SND_SOC_SAMSUNG=y
 CONFIG_SND_SOC_AK4613=y
@@ -372,6 +383,7 @@ CONFIG_RTC_DRV_XGENE=y
 CONFIG_RTC_DRV_S3C=y
 CONFIG_DMADEVICES=y
 CONFIG_PL330_DMA=y
+CONFIG_DMA_BCM2835=m
 CONFIG_TEGRA20_APB_DMA=y
 CONFIG_QCOM_BAM_DMA=y
 CONFIG_QCOM_HIDMA_MGMT=y
@@ -394,8 +406,10 @@ CONFIG_MSM_MMCC_8996=y
 CONFIG_HWSPINLOCK_QCOM=y
 CONFIG_MAILBOX=y
 CONFIG_ARM_MHU=y
+CONFIG_BCM2835_MBOX=y
 CONFIG_HI6220_MBOX=y
 CONFIG_ARM_SMMU=y
+CONFIG_RASPBERRYPI_POWER=y
 CONFIG_QCOM_SMEM=y
 CONFIG_QCOM_SMD=y
 CONFIG_QCOM_SMD_RPM=y
@@ -403,6 +417,7 @@ CONFIG_ARCH_TEGRA_132_SOC=y
 CONFIG_ARCH_TEGRA_210_SOC=y
 CONFIG_EXTCON_USB_GPIO=y
 CONFIG_PWM=y
+CONFIG_PWM_BCM2835=m
 CONFIG_PWM_TEGRA=m
 CONFIG_COMMON_RESET_HI6220=y
 CONFIG_PHY_RCAR_GEN3_USB2=y
@@ -414,6 +429,7 @@ CONFIG_ACPI=y
 CONFIG_IIO=y
 CONFIG_EXYNOS_ADC=y
 CONFIG_PWM_SAMSUNG=y
+CONFIG_RASPBERRYPI_FIRMWARE=y
 CONFIG_EXT2_FS=y
 CONFIG_EXT3_FS=y
 CONFIG_EXT4_FS_POSIX_ACL=y
-- 
2.9.3




More information about the linux-rpi-kernel mailing list