[PATCH 1/2] ARM: bcm2835: Fix names for the Raspberry Pi GPIO lines

Stefan Wahren stefan.wahren at i2se.com
Sun Nov 13 10:12:08 PST 2016


There are some differences between the schematics and the official firmware
DTS [1]. So based on these additional information the following has been
changed:

* use consistent "CAM_GPIO1" for camera LED
* use consistent "CAM_GPIO0" for camera shutdown
* add "USB_LIMIT" for USB current limit (0=600mA, 1=1200mA)

[1] - https://github.com/raspberrypi/documentation/blob/master/configuration/images/dt-blob.dts

Signed-off-by: Stefan Wahren <stefan.wahren at i2se.com>
---
 arch/arm/boot/dts/bcm2835-rpi-a-plus.dts |    4 ++--
 arch/arm/boot/dts/bcm2835-rpi-a.dts      |    4 ++--
 arch/arm/boot/dts/bcm2835-rpi-b-plus.dts |    2 +-
 arch/arm/boot/dts/bcm2835-rpi-b.dts      |    4 ++--
 4 files changed, 7 insertions(+), 7 deletions(-)

diff --git a/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts b/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts
index 5a22c79..d070454 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts
@@ -63,13 +63,13 @@
 			  "SCL0",
 			  "NC", /* GPIO30 */
 			  "NC", /* GPIO31 */
-			  "NC", /* GPIO32 */
+			  "CAM_GPIO1", /* GPIO32 */
 			  "NC", /* GPIO33 */
 			  "NC", /* GPIO34 */
 			  "PWR_LOW_N", /* GPIO35 */
 			  "NC", /* GPIO36 */
 			  "NC", /* GPIO37 */
-			  "NC", /* GPIO38 */
+			  "USB_LIMIT", /* GPIO38 */
 			  "NC", /* GPIO39 */
 			  "PWM0_OUT", /* GPIO40 */
 			  "CAM_GPIO0", /* GPIO41 */
diff --git a/arch/arm/boot/dts/bcm2835-rpi-a.dts b/arch/arm/boot/dts/bcm2835-rpi-a.dts
index 54f98c5..46d078e 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-a.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-a.dts
@@ -29,7 +29,7 @@
 			  "SDA1",
 			  "SCL1",
 			  "GPIO_GCLK",
-			  "CAM_CLK",
+			  "CAM_GPIO1",
 			  "LAN_RUN",
 			  "SPI_CE1_N",
 			  "SPI_CE0_N",
@@ -52,7 +52,7 @@
 			  "GPIO24",
 			  "GPIO25",
 			  "NC", /* GPIO26 */
-			  "CAM_GPIO",
+			  "CAM_GPIO0",
 			  /* Binary number representing build/revision */
 			  "CONFIG0",
 			  "CONFIG1",
diff --git a/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts b/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts
index b67587e..432088e 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts
@@ -71,7 +71,7 @@
 			  "PWR_LOW_N", /* GPIO35 */
 			  "NC", /* GPIO36 */
 			  "NC", /* GPIO37 */
-			  "NC", /* GPIO38 */
+			  "USB_LIMIT", /* GPIO38 */
 			  "NC", /* GPIO39 */
 			  "PWM0_OUT", /* GPIO40 */
 			  "CAM_GPIO0", /* GPIO41 */
diff --git a/arch/arm/boot/dts/bcm2835-rpi-b.dts b/arch/arm/boot/dts/bcm2835-rpi-b.dts
index 71f50e1..4d56fe3 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-b.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-b.dts
@@ -30,7 +30,7 @@
 			  "SDA1",
 			  "SCL1",
 			  "GPIO_GCLK",
-			  "CAM_CLK",
+			  "CAM_GPIO1",
 			  "LAN_RUN",
 			  "SPI_CE1_N",
 			  "SPI_CE0_N",
@@ -53,7 +53,7 @@
 			  "GPIO24",
 			  "GPIO25",
 			  "NC", /* GPIO26 */
-			  "CAM_GPIO",
+			  "CAM_GPIO0",
 			  /* Binary number representing build/revision */
 			  "CONFIG0",
 			  "CONFIG1",
-- 
1.7.9.5




More information about the linux-rpi-kernel mailing list