[PATCH] arm64: dts: rockchip: Add buttons to Kobol Helios64

[Igor Velkov via B4 Relay]

From: Igor Velkov <iav at iav.lv>

The Helios64 front panel has Power and Recovery buttons. Power is
wired to GPIO0_A5 and Recovery to SARADC channel 1. The board also
routes a User1 button signal to GPIO0_A3 on front panel header P3.

Describe Power and User1 as gpio-keys and Recovery as adc-keys.
The SARADC reference is the 1V8_S3 rail from RK808 LDO_REG3, so add
that regulator.

Assisted-by: LLM
Signed-off-by: Igor Velkov <iav at iav.lv>
---
Tested on 7.3-rc5 with evtest: Power reports KEY_POWER, Recovery
reports BTN_1. Power wakes the board from s2idle. User1 has no button
on the enclosure and is untested.
---
 .../boot/dts/rockchip/rk3399-kobol-helios64.dts    | 64 ++++++++++++++++++++++
 1 file changed, 64 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3399-kobol-helios64.dts b/arch/arm64/boot/dts/rockchip/rk3399-kobol-helios64.dts
index b2de018a7d36..d146e5075b4f 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-kobol-helios64.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-kobol-helios64.dts
@@ -11,6 +11,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/input/input.h>
 #include "rk3399.dtsi"
 
 / {
@@ -23,6 +24,20 @@ aliases {
 		mmc1 = &sdhci;
 	};
 
+	adc-keys {
+		compatible = "adc-keys";
+		io-channels = <&saradc 1>;
+		io-channel-names = "buttons";
+		keyup-threshold-microvolt = <1800000>;
+		poll-interval = <100>;
+
+		button-recovery {
+			label = "Recovery";
+			linux,code = <BTN_1>;
+			press-threshold-microvolt = <100000>;
+		};
+	};
+
 	avdd_0v9_s0: regulator-avdd-0v9-s0 {
 		compatible = "regulator-fixed";
 		regulator-name = "avdd_0v9_s0";
@@ -68,6 +83,27 @@ fan2 {
 		cooling-levels = <0 80 170 255>;
 	};
 
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwr_btn &user1_btn>;
+
+		button-power {
+			debounce-interval = <100>;
+			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
+			label = "Power";
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+
+		button-user1 {
+			debounce-interval = <100>;
+			gpios = <&gpio0 RK_PA3 GPIO_ACTIVE_LOW>;
+			label = "User Button 1";
+			linux,code = <BTN_0>;
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
@@ -352,6 +388,19 @@ regulator-state-mem {
 				};
 			};
 
+			vcc1v8_s3: LDO_REG3 {
+				regulator-name = "vcc1v8_s3";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
 			vcc_sdio_s0: LDO_REG4 {
 				regulator-name = "vcc_sdio_s0";
 				regulator-always-on;
@@ -434,6 +483,16 @@ &pcie0 {
 };
 
 &pinctrl {
+	buttons {
+		pwr_btn: pwr-btn {
+			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		user1_btn: user1-btn {
+			rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
 	gmac {
 		gphy_reset: gphy-reset {
 			rockchip,pins = <3 RK_PB7 RK_FUNC_GPIO &pcfg_output_low>;
@@ -503,6 +562,11 @@ &pwm1 {
 	status = "okay";
 };
 
+&saradc {
+	vref-supply = <&vcc1v8_s3>;
+	status = "okay";
+};
+
 &sdhci {
 	bus-width = <8>;
 	mmc-hs200-1_8v;

---
base-commit: 23d8f49fcae5d72b77744c7f349c12462c3bb748
change-id: 20260930-helios64-buttons-b93ad4e8ee2e

Best regards,
-- 
Igor Velkov <iav at iav.lv>