[PATCH 05/40] arm64: dts: rockchip: Add frl-enable-gpios to rk3576-luckfox-core3576

[Heiko Stuebner]

Am Montag, 20. April 2026, 13:00:25 Mitteleuropäische Sommerzeit schrieb Cristian Ciocaltea:
> Hi Heiko,
> 
> On 4/18/26 2:12 AM, Heiko Stuebner wrote:
> > Hi Cristian,
> > 
> > Am Freitag, 17. April 2026, 18:34:17 Mitteleuropäische Sommerzeit schrieb Cristian Ciocaltea:
> >> On 4/17/26 2:32 PM, Heiko Stuebner wrote:
> >>> the comments below apply sort of to all patches in that series.
> >>>
> >>> Am Freitag, 17. April 2026, 11:24:39 Mitteleuropäische Sommerzeit schrieb Cristian Ciocaltea:
> >>>> The board exposes the GPIO4_C6 line to control the voltage bias on the
> >>>> HDMI data lines.  It must be asserted when operating in HDMI 2.1 FRL
> >>>> mode and deasserted for HDMI 1.4/2.0 TMDS mode.
> >>>>
> >>>> Wire up the HDMI node to the GPIO line using the frl-enable-gpios
> >>>> property and drop the line from the vcc_5v0_hdmi regulator to allow
> >>>> adjusting the bias when transitioning between TMDS and FRL operating
> >>>> modes.
> 
> [...]
> 
> >>>
> >>>
> >>>> @@ -231,6 +228,8 @@ &gpu {
> >>>>  };
> >>>>  
> >>>>  &hdmi {
> >>>> +	pinctrl-0 = <&hdmi_txm0_pins &hdmi_tx_scl &hdmi_tx_sda &hdmi_frl_en>;
> >>>> +	frl-enable-gpios = <&gpio4 RK_PC6 GPIO_ACTIVE_LOW>;
> >>>
> >>> this should be sorted the other way around I think.
> >>>
> >>> Also please provide a pinctrl-names property too. If for whatever reason
> >>> the dw-hdmi aquires a 2nd pinctrl state in the future, this makes sure
> >>> board DTs are staying in the "old" compatible mode until they are adapted.
> >>
> >> Just to make sure I fully understand, the convention is that 
> >>
> >>   pinctrl-names = "default";
> >>
> >> should be always provided, even when the node overrides an existing pinctrl-0
> >> property?
> >>
> >> E.g. in rk3576.dtsi we have:
> >>
> >>   hdmi: hdmi at 27da0000 {
> >>     ...
> >>     pinctrl-names = "default";
> >>     pinctrl-0 = <&hdmi_txm0_pins &hdmi_tx_scl &hdmi_tx_sda>;
> >>     ...
> >>   }
> >>
> >> Hence I omitted pinctrl-names which doesn't change and just appended
> >> &hdmi_frl_en to pinctrl-0's original value.
> > 
> > correct, please always provide a pinctrl-names entry when setting a new
> > pinctrl-0 .
> > 
> > The background is, imagine you have a base:
> > 
> > pinctrl-names = "default";
> > pinstrl-0 = <....>;
> > 
> > and override pinctrl-0 in a board.
> > 
> > Now a newer binding introduces a 2nd pinctrl state "foo". Of course
> > we're backwards compatible, and both are valid and the driver checks
> > what states are defined.
> > 
> > So the base sets:
> > pinctrl-names = "default", "foo";
> > pinctrl-0 = <...>;
> > pinctrl-1 = <...>;
> > 
> > in your (old) board you override pinctrl-0, but the driver still sees
> > the new variant with 2 pinctrl states, where it should've stayed with
> > the legacy 1-state, until the board-dts might get adapted in the future.
> > 
> > 
> > And I know, we're likely not doing that everywhere, and also in most
> > cases it won't really matter, but still it is safer and sets the better
> > precedent :-) .
> 
> Thanks for the detailed explanation, that clears things up!
> 
> There are several other nodes (e.g. i2c, pwm, uart) that also lack
> pinctrl-names despite providing pinctrl-0 - I can address those in a
> separate patch.

As said above it is an ideal to aspire to (having -names together with
defining states), but if you want to add the "missing" -names,
go ahead :-) .


> I also noticed an inconsistency in property ordering: some nodes place
> pinctrl-names before pinctrl-<n> and others after.  I have always used
> the former, but we should probably prefer the latter to stay consistent
> with how clocks, resets, phys, etc. are ordered.
> 
> Thoughts?

There is sort of a "conflict" between regular ordering and possibly
better readability. I.e. the dt-writing guidelines propose alphabetical
ordering which I guess puts numbers before letters.

On the other hand the semantic definition of list the states and then
define them (names first, -0, -1, etc second) looks more sensible from
a understanding standpoint.


But there we'd end up with special rules, so just sticking to the
base sorting will cause less friction in the long run I think.
Aka, -0, -1 first; -names after, follows the main sorting suggestions
so it's easy to explain to newcomers.


But please don't re-sort existing entries :-)


Heiko