[PATCH v3 2/2] arm64: dts: rockchip: Add rk3588s-orangepi-cm5-base device tree
Laurent Pinchart
laurent.pinchart at ideasonboard.com
Mon Oct 27 14:56:36 PDT 2025
The Orange Pi CM5 Base board is a carrier board for the Orange Pi CM5
compute module. It has 3 ethernet ports, 2 USB ports, one HDMI output
and 4 CSI-2 inputs.
The device tree is split in two files, a .dtsi for the compute module
and a .dts for the carrier board. All the devices present on the carrier
board are enabled and tested, with the exception of the IR receiver due
to missing support for input capture in the PWM device's DT binding (and
driver).
This work is based on a combination of the Orange Pi 5 device tree from
the upstream kernel and the Orange Pi CM5 device tree from the BSP
kernel. All nodes and properties have been carefully checked to the best
of my abilities against the schematics of the carrier board. The
schematics of the compute module is not available publicly, so the
configuration of the PMIC hasn't been double-checked.
Signed-off-by: Laurent Pinchart <laurent.pinchart at ideasonboard.com>
---
Changes since v2:
- Replace tmds-enable-gpios with pinmux + pull-up
Changes since v1:
- Rename enable-gpios to tmds-enable-gpios
- Add pinctrl entries for camera reset pins
- Move gpu and pd_gpu enablement to CM5
- Move mmc0 alias to CM5
- Drop tx_delay from gmac1
- Reorder properties in carrier board regulators
- Set tsadc pinctrl to gpio
---
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../rockchip/rk3588s-orangepi-cm5-base.dts | 355 +++++++++++++
.../dts/rockchip/rk3588s-orangepi-cm5.dtsi | 473 ++++++++++++++++++
3 files changed, 829 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3588s-orangepi-cm5-base.dts
create mode 100644 arch/arm64/boot/dts/rockchip/rk3588s-orangepi-cm5.dtsi
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index ad684e3831bc..40ab915b80ac 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -202,6 +202,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-nanopi-r6c.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-odroid-m2.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-orangepi-5.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-orangepi-5b.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-orangepi-cm5-base.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-roc-pc.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-rock-5a.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-rock-5c.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-cm5-base.dts b/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-cm5-base.dts
new file mode 100644
index 000000000000..c955ca983e68
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-cm5-base.dts
@@ -0,0 +1,355 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+
+#include "rk3588s-orangepi-cm5.dtsi"
+
+/ {
+ model = "Xunlong Orange Pi CM5 Base";
+ compatible = "xunlong,orangepi-cm5-base", "xunlong,orangepi-cm5", "rockchip,rk3588s";
+
+ aliases {
+ ethernet0 = &gmac1;
+ mmc1 = &sdmmc;
+ };
+
+ chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&key1_pin>;
+
+ button {
+ gpios = <&gpio3 RK_PC6 GPIO_ACTIVE_LOW>;
+ label = "USERKEY";
+ linux,code = <BTN_MISC>;
+ debounce-interval = <50>;
+ wakeup-source;
+ };
+ };
+
+ hdmi0-con {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi0_con_in: endpoint {
+ remote-endpoint = <&hdmi0_out_con>;
+ };
+ };
+ };
+
+ pwm-leds {
+ compatible = "pwm-leds";
+
+ led-1 {
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_STATUS;
+ linux,default-trigger = "heartbeat";
+ max-brightness = <255>;
+ pwms = <&pwm2 0 25000 0>;
+ };
+
+ led-2 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_WAN;
+ max-brightness = <255>;
+ pwms = <&pwm4 0 25000 PWM_POLARITY_INVERTED>;
+ };
+
+ led-3 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <0>;
+ max-brightness = <255>;
+ pwms = <&pwm5 0 25000 PWM_POLARITY_INVERTED>;
+ };
+
+ led-4 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <1>;
+ max-brightness = <255>;
+ pwms = <&pwm6 0 25000 0>;
+ };
+ };
+
+ vbus_5v0: vbus-5v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vbus_5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&gpio0 RK_PD3 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vbus_5v0_en_pin>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc_3v3: regulator-vcc-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpio = <&gpio4 RK_PA3 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc_3v3_en_pin>;
+ startup-delay-us = <50000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc5v0_sys: regulator-vcc-5v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+};
+
+&combphy0_ps {
+ status = "okay";
+};
+
+&combphy2_psu {
+ status = "okay";
+};
+
+&gmac1 {
+ clock_in_out = "output";
+ phy-handle = <&rgmii_phy>;
+ phy-mode = "rgmii-id";
+ phy-supply = <&vcc_3v3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac1_miim
+ &gmac1_rx_bus2
+ &gmac1_tx_bus2
+ &gmac1_rgmii_clk
+ &gmac1_rgmii_bus>;
+ status = "okay";
+};
+
+&hdmi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdmim0_tx0_cec &hdmim0_tx0_hpd
+ &hdmim0_tx0_scl &hdmim0_tx0_sda
+ &hdmi_frl_pin>;
+ status = "okay";
+};
+
+&hdmi0_in {
+ hdmi0_in_vp0: endpoint {
+ remote-endpoint = <&vp0_out_hdmi0>;
+ };
+};
+
+&hdmi0_out {
+ hdmi0_out_con: endpoint {
+ remote-endpoint = <&hdmi0_con_in>;
+ };
+};
+
+&hdmi0_sound {
+ status = "okay";
+};
+
+&hdptxphy0 {
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-0 = <&i2c1m2_xfer>;
+ status = "okay";
+
+ rtc at 51 {
+ compatible = "haoyu,hym8563";
+ reg = <0x51>;
+ #clock-cells = <0>;
+ clock-output-names = "hym8563";
+ pinctrl-names = "default";
+ pinctrl-0 = <&rtc_int_pin>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PB0 IRQ_TYPE_LEVEL_LOW>;
+ wakeup-source;
+ };
+};
+
+&i2s5_8ch {
+ status = "okay";
+};
+
+&mdio1 {
+ rgmii_phy: ethernet-phy at 1 {
+ /* YT8531C */
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0x1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_phy_pin>;
+ reset-assert-us = <20000>;
+ reset-deassert-us = <100000>;
+ reset-gpios = <&gpio1 RK_PC1 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&pcie2x1l1 {
+ reset-gpios = <&gpio4 RK_PA2 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc_3v3>;
+ status = "okay";
+};
+
+&pcie2x1l2 {
+ reset-gpios = <&gpio3 RK_PD1 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc_3v3>;
+ status = "okay";
+};
+
+&pinctrl {
+ camera {
+ cam1_reset_pin: cam1-reset-pin {
+ rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ cam2_reset_pin: cam2-reset-pin {
+ rockchip,pins = <1 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ cam3_reset_pin: cam3-reset-pin {
+ rockchip,pins = <1 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ cam4_reset_pin: cam4-reset-pin {
+ rockchip,pins = <1 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ ethernet {
+ rgmii_phy_pin: rgmii-phy-pin {
+ rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ gpio-key {
+ key1_pin: key1-pin {
+ rockchip,pins = <3 RK_PC6 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ hdmi {
+ hdmi_frl_pin: hdmi-frl-pin {
+ rockchip,pins = <4 RK_PB5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ power {
+ vcc_3v3_en_pin: vcc-3v3-en-pin {
+ rockchip,pins = <4 RK_PA3 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+
+ rtc {
+ rtc_int_pin: rtc-int-pin {
+ rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb {
+ vbus_5v0_en_pin: vbus-5v0-en-pin {
+ rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pwm2 {
+ status = "okay";
+};
+
+&pwm4 {
+ status = "okay";
+};
+
+&pwm5 {
+ pinctrl-0 = <&pwm5m1_pins>;
+ status = "okay";
+};
+
+&pwm6 {
+ status = "okay";
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ disable-wp;
+ max-frequency = <150000000>;
+ no-mmc;
+ no-sdio;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc_3v3_s3>;
+ vqmmc-supply = <&vccio_sd_s0>;
+ status = "okay";
+};
+
+&u2phy0 {
+ status = "okay";
+};
+
+&u2phy0_otg {
+ phy-supply = <&vbus_5v0>;
+ status = "okay";
+};
+
+&u2phy2 {
+ status = "okay";
+};
+
+&u2phy2_host {
+ phy-supply = <&vbus_5v0>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-0 = <&uart2m0_xfer>;
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&usb_host0_xhci {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbdp_phy0 {
+ status = "okay";
+};
+
+&vop {
+ status = "okay";
+};
+
+&vop_mmu {
+ status = "okay";
+};
+
+&vp0 {
+ vp0_out_hdmi0: endpoint at ROCKCHIP_VOP2_EP_HDMI0 {
+ reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+ remote-endpoint = <&hdmi0_in_vp0>;
+ };
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-cm5.dtsi b/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-cm5.dtsi
new file mode 100644
index 000000000000..616a4674cbfe
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-cm5.dtsi
@@ -0,0 +1,473 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/clock/rockchip,rk3588-cru.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+#include "rk3588s.dtsi"
+#include "rk8xx.h"
+
+/ {
+ aliases {
+ mmc0 = &sdhci;
+ };
+
+ /* Can't be verified due to missing schematics for the CM5. */
+ vcc_1v1_nldo_s3: vcc-1v1-nldo-s3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_1v1_nldo_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+};
+
+&cpu_b0 {
+ cpu-supply = <&vdd_cpu_big0_s0>;
+};
+
+&cpu_b1 {
+ cpu-supply = <&vdd_cpu_big0_s0>;
+};
+
+&cpu_b2 {
+ cpu-supply = <&vdd_cpu_big1_s0>;
+};
+
+&cpu_b3 {
+ cpu-supply = <&vdd_cpu_big1_s0>;
+};
+
+&cpu_l0 {
+ cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l1 {
+ cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l2 {
+ cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l3 {
+ cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&gpu {
+ mali-supply = <&vdd_gpu_s0>;
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-0 = <&i2c0m2_xfer>;
+ status = "okay";
+
+ vdd_cpu_big0_s0: regulator at 42 {
+ compatible = "rockchip,rk8602";
+ reg = <0x42>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_cpu_big0_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-ramp-delay = <2300>;
+ vin-supply = <&vcc5v0_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_cpu_big1_s0: regulator at 43 {
+ compatible = "rockchip,rk8603", "rockchip,rk8602";
+ reg = <0x43>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_cpu_big1_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-ramp-delay = <2300>;
+ vin-supply = <&vcc5v0_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+};
+
+&i2c2 {
+ status = "okay";
+
+ vdd_npu_s0: regulator at 42 {
+ compatible = "rockchip,rk8602";
+ reg = <0x42>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_npu_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <2300>;
+ vin-supply = <&vcc5v0_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+};
+
+&pd_gpu {
+ domain-supply = <&vdd_gpu_s0>;
+};
+
+&sdhci {
+ bus-width = <8>;
+ no-sdio;
+ no-sd;
+ non-removable;
+ max-frequency = <200000000>;
+ mmc-hs400-1_8v;
+ mmc-hs400-enhanced-strobe;
+ status = "okay";
+};
+
+&spi2 {
+ assigned-clocks = <&cru CLK_SPI2>;
+ assigned-clock-rates = <200000000>;
+ num-cs = <1>;
+ pinctrl-0 = <&spi2m2_cs0 &spi2m2_pins>;
+ status = "okay";
+
+ pmic at 0 {
+ compatible = "rockchip,rk806";
+ reg = <0x0>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
+ <&rk806_dvs2_null>, <&rk806_dvs3_null>;
+ spi-max-frequency = <1000000>;
+ system-power-controller;
+ rockchip,reset-mode = <RK806_RESET>;
+
+ vcc1-supply = <&vcc5v0_sys>;
+ vcc2-supply = <&vcc5v0_sys>;
+ vcc3-supply = <&vcc5v0_sys>;
+ vcc4-supply = <&vcc5v0_sys>;
+ vcc5-supply = <&vcc5v0_sys>;
+ vcc6-supply = <&vcc5v0_sys>;
+ vcc7-supply = <&vcc5v0_sys>;
+ vcc8-supply = <&vcc5v0_sys>;
+ vcc9-supply = <&vcc5v0_sys>;
+ vcc10-supply = <&vcc5v0_sys>;
+ vcc11-supply = <&vcc_2v0_pldo_s3>;
+ vcc12-supply = <&vcc5v0_sys>;
+ vcc13-supply = <&vcc_1v1_nldo_s3>;
+ vcc14-supply = <&vcc_1v1_nldo_s3>;
+ vcca-supply = <&vcc5v0_sys>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ rk806_dvs1_null: dvs1-null-pins {
+ pins = "gpio_pwrctrl1";
+ function = "pin_fun0";
+ };
+
+ rk806_dvs2_null: dvs2-null-pins {
+ pins = "gpio_pwrctrl2";
+ function = "pin_fun0";
+ };
+
+ rk806_dvs3_null: dvs3-null-pins {
+ pins = "gpio_pwrctrl3";
+ function = "pin_fun0";
+ };
+
+ regulators {
+ vdd_gpu_s0: dcdc-reg1 {
+ regulator-name = "vdd_gpu_s0";
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+ regulator-enable-ramp-delay = <400>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_cpu_lit_s0: dcdc-reg2 {
+ regulator-name = "vdd_cpu_lit_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_log_s0: dcdc-reg3 {
+ regulator-name = "vdd_log_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <750000>;
+ regulator-ramp-delay = <12500>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <750000>;
+ };
+ };
+
+ vdd_vdenc_s0: dcdc-reg4 {
+ regulator-name = "vdd_vdenc_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_ddr_s0: dcdc-reg5 {
+ regulator-name = "vdd_ddr_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <900000>;
+ regulator-ramp-delay = <12500>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <850000>;
+ };
+ };
+
+ vdd2_ddr_s3: dcdc-reg6 {
+ regulator-name = "vdd2_ddr_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <1100000>;
+ regulator-min-microvolt = <1100000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_2v0_pldo_s3: dcdc-reg7 {
+ regulator-name = "vdd_2v0_pldo_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <2000000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <2000000>;
+ };
+ };
+
+ vcc_3v3_s3: dcdc-reg8 {
+ regulator-name = "vcc_3v3_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vddq_ddr_s0: dcdc-reg9 {
+ regulator-name = "vddq_ddr_s0";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v8_s3: dcdc-reg10 {
+ regulator-name = "vcc_1v8_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ avcc_1v8_s0: pldo-reg1 {
+ regulator-name = "avcc_1v8_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v8_s0: pldo-reg2 {
+ regulator-name = "vcc_1v8_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ avdd_1v2_s0: pldo-reg3 {
+ regulator-name = "avdd_1v2_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_3v3_s0: pldo-reg4 {
+ regulator-name = "vcc_3v3_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd_s0: pldo-reg5 {
+ regulator-name = "vccio_sd_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ pldo6_s3: pldo-reg6 {
+ regulator-name = "pldo6_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdd_0v75_s3: nldo-reg1 {
+ regulator-name = "vdd_0v75_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <750000>;
+ };
+ };
+
+ vdd_ddr_pll_s0: nldo-reg2 {
+ regulator-name = "vdd_ddr_pll_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <850000>;
+ };
+ };
+
+ avdd_0v75_s0: nldo-reg3 {
+ regulator-name = "avdd_0v75_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_0v85_s0: nldo-reg4 {
+ regulator-name = "vdd_0v85_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_0v75_s0: nldo-reg5 {
+ regulator-name = "vdd_0v75_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&tsadc {
+ /*
+ * The TSADC_SHUT pin is exposed to carrier boards as a signal named
+ * PMIC_RESET_L, meant to be driven externally. Reference carrier
+ * boards connect it to a reset button that pulls the signal to GND
+ * through a 100Ω resistor. This is too weak to overcome even the
+ * minimum drive strength of the TSADC_SHUT pin when driven in
+ * push-pull mode. Configure it as a GPIO, reset will be generated
+ * through the CRU.
+ */
+ pinctrl-0 = <&tsadc_gpio_func>;
+ status = "okay";
+};
--
Regards,
Laurent Pinchart
More information about the Linux-rockchip
mailing list