[PATCH v3 3/4] arm64: dts: rockchip: describe I2c Bus 1 and IMX258 world camera on PinePhone Pro

Tue May 13 11:23:40 PDT 2025

Hi Olivier,

Am Freitag, 9. Mai 2025, 23:51:39 Mitteleuropäische Sommerzeit schrieb Olivier Benjamin:
> Add the description of the rear/world camera (IMX258) on the PinePhone Pro
> to the device dts file.
> It receives commands on the I2C Bus 1 at address 0x1a and transmits data
> over CSI-MIPI.
> 
> The I2C address for IMX258 can be found in the IMX258-0AQH5 Software
> Reference Manual, page 24, section 2.3.1: 0b0011010 = 0x1a.
> Section 3 indicates the module has 4 pairs of data lines. While 4-lane
> mode is nominal, 2-lane mode should also be supported.
> 
> The pin muxing info was extracted from the PinePhone Pro schematic v1.0
> as well as the RK3399 datasheet revision 1.8.
> 
> Table 2-3 in section 2.8 of the RK3399 datasheet contains the mapping
> of IO functions for the SoC pins. Page 52 shows GPIO1_A0, page 54 shows
> GPIO2_D4.
> 
> For I2C power, the PinePhone Pro schematic page 11 quadrants A4 and A5:
> RK3399_J.AA8 and RK3399_J.Y8 get power from vcaa1v8_codec, so turn it on
> 
> The IMX258 also uses the following regulators, expected by its driver:
>  - vana (2.8V analog), called AVDD2V8_DVP on P.18 q.C1 and derived from
>    VCC1V8_S3 on P.13 q.B2
>  - vdig (1.2V digital core), called DVDD_DVP on P.18 q.C1 and shown on
>    P.18 q.D3 to be equivalent to VCC1V2_DVP derived from VCC3V3_SYS on
>    P.13 q.B3. Note that this regulator's voltage is inconsistently
>    labeled either 1.2V or 1.5V
> 
> RK3399_J.AG1 is GPIO4_A1/I2C1_SDA, RK3399_J.Y6 is GPIO4_A2/I2C1_SCL
> This is the default pinctrl "i2c1_xfer" for i2c1 from rk3399-base.
> 
> For the reset (RESET) signal:
> page 11 quadrant D2             | p.18 q.C3-4 | p.18 q.C2
> RK3399_E.R25 -> GPIO1_A0 -> Camera_RST -> MIPI_RST0 -> IMX258.12
> 
> For the powerdown (PWDN) signal:
> page 11 quadrants B4-5          | p.18 q.C2
> RK3399_G.AF8 -> GPIO2_D4 -> DVP_PDN1_H -> IMX258.14
> 
> Helped-by: Dragan Simic <dsimic at manjaro.org>
> Co-developed-by: Ondrej Jirman <megi at xff.cz>
> Signed-off-by: Ondrej Jirman <megi at xff.cz>
> Signed-off-by: Olivier Benjamin <olivier.benjamin at bootlin.com>

how independent are the devicetree changes from the binding changes?
As the binding change "only" includes other properties.

Heiko

> ---
>  .../boot/dts/rockchip/rk3399-pinephone-pro.dts     | 94 ++++++++++++++++++++++
>  1 file changed, 94 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts b/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
> index 04ba4c4565d0a205e2e46d7535c6a3190993621d..588e2d8a049cc649aa227c7a885bd494f23fbdf8 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
> @@ -114,6 +114,16 @@ vcc3v3_sys: regulator-vcc3v3-sys {
>  		vin-supply = <&vcc_sys>;
>  	};
>  
> +	avdd2v8_dvp: regulator-avdd2v8-dvp {
> +		compatible = "regulator-fixed";
> +		regulator-name = "avdd2v8_dvp";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <2800000>;
> +		regulator-max-microvolt = <2800000>;
> +		vin-supply = <&vcc3v3_sys>;
> +	};
> +
>  	vcca1v8_s3: regulator-vcc1v8-s3 {
>  		compatible = "regulator-fixed";
>  		regulator-name = "vcca1v8_s3";
> @@ -136,6 +146,16 @@ vcc1v8_codec: regulator-vcc1v8-codec {
>  		vin-supply = <&vcc3v3_sys>;
>  	};
>  
> +	vcc1v2_dvp: regulator-vcc1v2-dvp {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc1v2_dvp";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <1200000>;
> +		regulator-max-microvolt = <1200000>;
> +		vin-supply = <&vcca1v8_s3>;
> +	};
> +
>  	wifi_pwrseq: sdio-wifi-pwrseq {
>  		compatible = "mmc-pwrseq-simple";
>  		clocks = <&rk818 1>;
> @@ -312,6 +332,8 @@ vcc3v0_touch: LDO_REG2 {
>  
>  			vcca1v8_codec: LDO_REG3 {
>  				regulator-name = "vcca1v8_codec";
> +				regulator-always-on;
> +				regulator-boot-on;
>  				regulator-min-microvolt = <1800000>;
>  				regulator-max-microvolt = <1800000>;
>  			};
> @@ -420,6 +442,46 @@ regulator-state-mem {
>  	};
>  };
>  
> +&i2c1 {
> +	clock-frequency = <400000>;
> +	pinctrl-0 = <&i2c1_xfer &cif_clkouta>;
> +	assigned-clocks = <&cru SCLK_CIF_OUT>;
> +	assigned-clock-rates = <24000000>;
> +	status = "okay";
> +
> +	wcam: camera at 1a {
> +		compatible = "sony,imx258";
> +		reg = <0x1a>;
> +		clocks = <&cru SCLK_CIF_OUT>; /* MIPI_MCLK0, derived from CIF_CLKO */
> +		clock-names = "xvclk";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&wcam_rst>;
> +		/* Note: both cameras also depend on vcca1v8_codec to power the I2C bus. */
> +		vif-supply = <&vcc1v8_dvp>;
> +		vana-supply = <&avdd2v8_dvp>;
> +		vdig-supply = <&vcc1v2_dvp>; /* DVDD_DVP is the same as VCC1V2_DVP */
> +		reset-gpios = <&gpio1 RK_PA0 GPIO_ACTIVE_LOW>;
> +		orientation = <1>; /* V4L2_CAMERA_ORIENTATION_BACK */
> +		rotation = <270>;
> +		lens-focus = <&wcam_lens>;
> +
> +		port {
> +			wcam_out: endpoint {
> +				remote-endpoint = <&mipi_in_wcam>;
> +				data-lanes = <1 2 3 4>;
> +				link-frequencies = /bits/ 64 <636000000>;
> +			};
> +		};
> +	};
> +
> +	wcam_lens: camera-lens at c {
> +		compatible = "dongwoon,dw9714";
> +		reg = <0x0c>;
> +		/* Same I2c bus as both cameras, depends on vcca1v8_codec for power. */
> +		vcc-supply = <&vcc1v8_dvp>;
> +	};
> +};
> +
>  &i2c3 {
>  	i2c-scl-rising-time-ns = <450>;
>  	i2c-scl-falling-time-ns = <15>;
> @@ -462,6 +524,28 @@ &io_domains {
>  	status = "okay";
>  };
>  
> +&isp1 {
> +	status = "okay";
> +
> +	ports {
> +		port at 0 {
> +			mipi_in_wcam: endpoint at 0 {
> +				reg = <0>;
> +				remote-endpoint = <&wcam_out>;
> +				data-lanes = <1 2 3 4>;
> +			};
> +		};
> +	};
> +};
> +
> +&mipi_dphy_rx0 {
> +	status = "okay";
> +};
> +
> +&isp1_mmu {
> +	status = "okay";
> +};
> +
>  &mipi_dsi {
>  	status = "okay";
>  	clock-master;
> @@ -495,6 +579,10 @@ mipi_in_panel: endpoint {
>  	};
>  };
>  
> +&mipi_dsi1 {
> +	status = "okay";
> +};
> +
>  &pmu_io_domains {
>  	pmu1830-supply = <&vcc_1v8>;
>  	status = "okay";
> @@ -507,6 +595,12 @@ pwrbtn_pin: pwrbtn-pin {
>  		};
>  	};
>  
> +	camera {
> +		wcam_rst: wcam-rst {
> +			rockchip,pins = <1 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +	};
> +
>  	leds {
>  		red_led_pin: red-led-pin {
>  			rockchip,pins = <4 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
> 
> 