[PATCH v1 3/3] arm64: dts: rockchip: add DTs for Sakura Pi RK3308B
Hsun Lai
i at chainsx.cn
Tue May 13 09:35:14 PDT 2025
The Sakura Pi RK3308B is a SBC based on the Rockchip RK3308 SoC.
Link: https://github.com/Sakura-Pi
Link: https://docs.sakurapi.org/article/sakurapi-rk3308b/introduce
The device contains the following hardware that is tested/working:
- 4 or 8GB eMMC
- SDMMC card slot
- Realtek SDIO WiFi 5/BT
- 256 or 512MB of RAM
- USB 2.0 port
- OTG port
- HDMI port
Signed-off-by: Hsun Lai <i at chainsx.cn>
---
Changes in v1:
- Add support for Sakura Pi RK3308B
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../dts/rockchip/rk3308-sakurapi-rk3308b.dts | 295 ++++++++++++++++++
2 files changed, 296 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3308-sakurapi-rk3308b.dts
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index e63c3f5eb..c9017bdc3 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -12,6 +12,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-evb.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-roc-cc.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-rock-pi-s.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-rock-s0.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-sakurapi-rk3308b.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3318-a95x-z2.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3326-anbernic-rg351m.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3326-anbernic-rg351v.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3308-sakurapi-rk3308b.dts b/arch/arm64/boot/dts/rockchip/rk3308-sakurapi-rk3308b.dts
new file mode 100644
index 000000000..91d8535fc
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3308-sakurapi-rk3308b.dts
@@ -0,0 +1,295 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 Akash Gajjar <akash at openedev.com>
+ * Copyright (c) 2019 Jagan Teki <jagan at openedev.com>
+ * Copyright (C) 2024 TheSnowfield <thesnowfield at sakurapi.org>
+ */
+
+/dts-v1/;
+#include "rk3308.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "Sakura Pi RK3308B";
+ compatible = "sakurapi,rk3308-sakurapi-rk3308b", "rockchip,rk3308";
+
+ aliases {
+ mmc0 = &emmc;
+ mmc1 = &sdmmc;
+ mmc2 = &sdio;
+ };
+
+ chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-0 = <&wifi_enable_h>;
+ pinctrl-names = "default";
+ /*
+ * On the module itself this is one of these (depending
+ * on the actual card populated):
+ * - SDIO_RESET_L_WL_REG_ON
+ * - PDN (power down when low)
+ */
+ reset-gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_LOW>;
+ };
+
+ vcc5v0_sys: vcc5v0-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ vdd_core: vdd-core {
+ compatible = "pwm-regulator";
+ pwms = <&pwm0 0 5000 1>;
+ regulator-name = "vdd_core";
+ regulator-min-microvolt = <827000>;
+ regulator-max-microvolt = <1340000>;
+ regulator-init-microvolt = <1015000>;
+ regulator-settling-time-up-us = <250>;
+ regulator-always-on;
+ regulator-boot-on;
+ pwm-supply = <&vcc5v0_sys>;
+ };
+
+ vdd_log: vdd-log {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_log";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc_ddr: vcc-ddr {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc_1v8: vcc-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_io>;
+ };
+
+ vcc_io: vcc-io {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_io";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc_phy: vcc-phy-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_phy";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vcc5v0_otg: vcc5v0-otg {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_otg";
+ regulator-always-on;
+ gpio = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ pinctrl-names = "default";
+ pinctrl-0 = <&otg_vbus_drv>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_core>;
+};
+
+&emmc {
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ non-removable;
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+};
+
+&sdmmc {
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ disable-wp;
+ pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_det &sdmmc_bus4>;
+ card-detect-delay = <800>;
+ status = "okay";
+};
+
+&sdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ non-removable;
+ no-mmc;
+ no-sd;
+ status = "okay";
+
+ brcmf: wifi at 1 {
+ compatible = "brcm,bcm43455-fmac";
+ reg = <1>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+ interrupt-names = "host-wake";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_host_wake>;
+ };
+};
+
+&dmac0 {
+ status = "okay";
+};
+
+/* SPI0 for external gpio pin */
+&spi0 {
+ status = "okay";
+
+ spi_dev at 0 {
+ compatible = "spidev";
+ reg = <0>;
+ spi-max-frequency = <0x2faf080>;
+ };
+};
+
+/* SPI1 for ws2812*/
+&spi1 {
+ status = "okay";
+
+ spi_dev at 0 {
+ compatible = "spidev";
+ reg = <0>;
+ spi-max-frequency = <0x2faf080>;
+ };
+};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&rtc_32k>;
+
+ usb {
+ otg_vbus_drv: otg-vbus-drv {
+ rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ sdio-pwrseq {
+ wifi_enable_h: wifi-enable-h {
+ rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ wifi {
+ wifi_host_wake: wifi-host-wake {
+ rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+
+ bluetooth {
+ bt_reg_on: bt-reg-on {
+ rockchip,pins = <4 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ bt_wake_host: bt-wake-host {
+ rockchip,pins = <4 RK_PB4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ host_wake_bt: host-wake-bt {
+ rockchip,pins = <4 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pwm0 {
+ status = "okay";
+ pinctrl-0 = <&pwm0_pin_pull_down>;
+};
+
+&saradc {
+ vref-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&pwm3 {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2m0_xfer>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm4345c5";
+ clocks = <&cru SCLK_RTC32K>;
+ clock-names = "lpo";
+ pinctrl-names = "default";
+ pinctrl-0 = <&host_wake_bt &bt_wake_host &bt_reg_on>;
+ device-wakeup-gpios = <&gpio4 RK_PB4 GPIO_ACTIVE_HIGH>;
+ host-wakeup-gpios = <&gpio4 RK_PB2 GPIO_ACTIVE_HIGH>;
+ shutdown-gpios = <&gpio4 RK_PB3 GPIO_ACTIVE_HIGH>;
+ max-speed = <1500000>;
+ };
+};
+
+&usb20_otg {
+ status = "okay";
+};
+
+&u2phy {
+ status = "okay";
+};
+
+&u2phy_otg {
+ status = "okay";
+};
+
+&u2phy_host {
+ state = "okay";
+};
+
+&usb_host_ehci {
+ status = "okay";
+};
+
+&usb_host_ohci{
+ status = "okay";
+};
--
2.34.1
More information about the Linux-rockchip
mailing list