[PATCH 7/8] arm64: dts: rockchip: Add SDMMC/SDIO controllers for RK3528

[Jonas Karlman]

Hi,

On 2025-03-01 11:47, Yao Zi wrote:
> RK3528 features two SDIO controllers and one SD/MMC controller, describe
> them in devicetree. Since their sample and drive clocks are located in
> the VO and VPU GRFs, corresponding syscons are added to make these
> clocks available.
> 
> Signed-off-by: Yao Zi <ziyao at disroot.org>
> ---
>  arch/arm64/boot/dts/rockchip/rk3528.dtsi | 62 ++++++++++++++++++++++++
>  1 file changed, 62 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/rockchip/rk3528.dtsi b/arch/arm64/boot/dts/rockchip/rk3528.dtsi
> index 5b334690356a..078c97fa1d9f 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3528.dtsi
> +++ b/arch/arm64/boot/dts/rockchip/rk3528.dtsi
> @@ -7,6 +7,7 @@
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
>  #include <dt-bindings/interrupt-controller/irq.h>
>  #include <dt-bindings/clock/rockchip,rk3528-cru.h>
> +#include <dt-bindings/reset/rockchip,rk3528-cru.h>
>  
>  / {
>  	compatible = "rockchip,rk3528";
> @@ -122,6 +123,16 @@ gic: interrupt-controller at fed01000 {
>  			#interrupt-cells = <3>;
>  		};
>  
> +		vpu_grf: syscon at ff340000 {
> +			compatible = "rockchip,rk3528-vpu-grf", "syscon";

vpu_grf is also used for gmac1, so should possible be a "syscon",
"simple-mfd", or have I misunderstood when to use simple-mfd ?

> +			reg = <0x0 0xff340000 0x0 0x8000>;
> +		};
> +
> +		vo_grf: syscon at ff360000 {
> +			compatible = "rockchip,rk3528-vo-grf", "syscon";

similar here, vo_grf is also used for gmac0.

> +			reg = <0x0 0xff360000 0x0 0x10000>;
> +		};
> +
>  		cru: clock-controller at ff4a0000 {
>  			compatible = "rockchip,rk3528-cru";
>  			reg = <0x0 0xff4a0000 0x0 0x30000>;
> @@ -251,5 +262,56 @@ uart7: serial at ffa28000 {
>  			reg-shift = <2>;
>  			status = "disabled";
>  		};
> +
> +		sdio0: mmc at ffc10000 {
> +			compatible = "rockchip,rk3528-dw-mshc",
> +				     "rockchip,rk3288-dw-mshc";
> +			reg = <0x0 0xffc10000 0x0 0x4000>;
> +			clocks = <&cru HCLK_SDIO0>,
> +				 <&cru CCLK_SRC_SDIO0>,
> +				 <&cru SCLK_SDIO0_DRV>,
> +				 <&cru SCLK_SDIO0_SAMPLE>;
> +			clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
> +			fifo-depth = <0x100>;
> +			interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
> +			max-frequency = <150000000>;
> +			resets = <&cru SRST_H_SDIO0>;
> +			reset-names = "reset";
> +			status = "disabled";
> +		};
> +
> +		sdio1: mmc at ffc20000 {
> +			compatible = "rockchip,rk3528-dw-mshc",
> +				     "rockchip,rk3288-dw-mshc";
> +			reg = <0x0 0xffc20000 0x0 0x4000>;
> +			clocks = <&cru HCLK_SDIO1>,
> +				 <&cru CCLK_SRC_SDIO1>,
> +				 <&cru SCLK_SDIO1_DRV>,
> +				 <&cru SCLK_SDIO1_SAMPLE>;
> +			clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
> +			fifo-depth = <0x100>;
> +			interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
> +			max-frequency = <150000000>;
> +			resets = <&cru SRST_H_SDIO1>;
> +			reset-names = "reset";
> +			status = "disabled";
> +		};
> +
> +		sdmmc: mmc at ffc30000 {
> +			compatible = "rockchip,rk3528-dw-mshc",
> +				     "rockchip,rk3288-dw-mshc";
> +			reg = <0x0 0xffc30000 0x0 0x4000>;
> +			clocks = <&cru HCLK_SDMMC0>,
> +				 <&cru CCLK_SRC_SDMMC0>,
> +				 <&cru SCLK_SDMMC_DRV>,
> +				 <&cru SCLK_SDMMC_SAMPLE>;
> +			clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
> +			fifo-depth = <0x100>;
> +			interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
> +			max-frequency = <150000000>;
> +			resets = <&cru SRST_H_SDMMC0>;
> +			reset-names = "reset";

Suggest adding default pinctrl props here:

  pinctrl-names = "default";
  pinctrl-0 = <&sdmmc_bus4>, <&sdmmc_clk>, <&sdmmc_cmd>, <&sdmmc_det>;

And possible also for sdio0 and sdio1.

Regards,
Jonas

> +			status = "disabled";
> +		};
>  	};
>  };