[PATCH v4 2/3] arm64: dts: rockchip: Add rk3588 based Radxa CM5

[Jimmy Hon]

> diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-radxa-cm5.dtsi b/arch/arm64/boot/dts/rockchip/rk3588s-radxa-cm5.dtsi
> new file mode 100644
> index 0000000000000000000000000000000000000000..d7946fe2bb4e721689e3eb4d60d8e9783402f05e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3588s-radxa-cm5.dtsi
> @@ -0,0 +1,156 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2025 Joseph Kogut <joseph.kogut at gmail.com>
> + */
> +
> +/*
> + * CM5 data sheet
> + * https://dl.radxa.com/cm5/v2210/radxa_cm5_v2210_schematic.pdf
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/soc/rockchip,vop2.h>
> +#include <dt-bindings/usb/pd.h>
> +
> +/ {
> +       compatible = "radxa,cm5", "rockchip,rk3588s";
> +
> +       aliases {
> +               mmc0 = &sdmmc;
Since the microSD card is on the carrier board, this alias should be
moved to the board DTS.

> +               mmc1 = &sdhci;
Most of the other Radxa rk3588 boards have the eMMC alias to mmc0. Why
does this use another convention?

> +               mmc2 = &sdio;
The sdio is not enabled. This alias won't be used.

> +       };
> +
> +       leds {
> +               compatible = "gpio-leds";
> +
> +               led_sys: led-0 {
> +                       color = <LED_COLOR_ID_BLUE>;
> +                       default-state = "on";
> +                       function = LED_FUNCTION_HEARTBEAT;
> +                       gpios = <&gpio4 RK_PB4 GPIO_ACTIVE_HIGH>;
> +                       linux,default-trigger = "heartbeat";
> +               };
> +       };
> +};
> +
> +&cpu_b0 {
> +       cpu-supply = <&vdd_cpu_big0_s0>;
> +};
> +
> +&cpu_b1 {
> +       cpu-supply = <&vdd_cpu_big0_s0>;
> +};
> +
> +&cpu_b2 {
> +       cpu-supply = <&vdd_cpu_big1_s0>;
> +};
> +
> +&cpu_b3 {
> +       cpu-supply = <&vdd_cpu_big1_s0>;
> +};
> +
> +&cpu_l0 {
> +       cpu-supply = <&vdd_cpu_lit_s0>;
> +};
> +
> +&cpu_l1 {
> +       cpu-supply = <&vdd_cpu_lit_s0>;
> +};
> +
> +&cpu_l2 {
> +       cpu-supply = <&vdd_cpu_lit_s0>;
> +};
> +
> +&cpu_l3 {
> +       cpu-supply = <&vdd_cpu_lit_s0>;
> +};
> +
> +&gmac1 {
> +       clock_in_out = "output";
> +       phy-handle = <&rgmii_phy1>;
> +       phy-mode = "rgmii-id";
> +       phy-supply = <&vcc_3v3_s0>;
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&gmac1_miim
> +                    &gmac1_tx_bus2
> +                    &gmac1_rx_bus2
> +                    &gmac1_rgmii_clk
> +                    &gmac1_rgmii_bus
> +                    &gmac1_clkinout>;
> +       status = "okay";
> +};
Should this be left disabled on the SoM dtsi? And only enabled on the
carrier board, if the carrier board has the RJ45 jack?
i.e. a handheld using the CM5 may not have ethernet
https://github.com/StonedEdge/Retro-Lite-CM5

> +
> +&gpu {
> +       mali-supply = <&vdd_gpu_s0>;
> +       status = "okay";
> +};
> +
> +&hdmi0 {
> +       status = "okay";
> +};
This should be moved to the carrier board DTS where all the other
HDMI0 nodes are.

> +
> +&i2c0 {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&i2c0m2_xfer>;
> +       status = "okay";
> +
> +       vdd_cpu_big0_s0: regulator at 42 {
> +               compatible = "rockchip,rk8602";
> +               reg = <0x42>;
> +               fcs,suspend-voltage-selector = <1>;
> +               regulator-name = "vdd_cpu_big0_s0";
> +               regulator-always-on;
> +               regulator-boot-on;
> +               regulator-min-microvolt = <550000>;
> +               regulator-max-microvolt = <1050000>;
> +               regulator-ramp-delay = <2300>;
> +               vin-supply = <&vcc5v0_sys>;
> +
> +               regulator-state-mem {
> +                       regulator-off-in-suspend;
> +               };
> +       };
> +
> +       vdd_cpu_big1_s0: regulator at 43 {
> +               compatible = "rockchip,rk8602";
> +               reg = <0x43>;
> +               fcs,suspend-voltage-selector = <1>;
> +               regulator-name = "vdd_cpu_big1_s0";
> +               regulator-always-on;
> +               regulator-boot-on;
> +               regulator-min-microvolt = <550000>;
> +               regulator-max-microvolt = <1050000>;
> +               regulator-ramp-delay = <2300>;
> +               vin-supply = <&vcc5v0_sys>;
> +
> +               regulator-state-mem {
> +                       regulator-off-in-suspend;
> +               };
> +       };
> +};
> +
> +&mdio1 {
> +       rgmii_phy1: phy at 1 {
> +               compatible = "ethernet-phy-ieee802.3-c22";
> +               reg = <0x1>;
> +       };
> +};
> +
> +&pd_gpu {
> +       domain-supply = <&vdd_gpu_s0>;
> +};
> +
> +&sdhci {
> +       bus-width = <8>;
> +       no-sdio;
> +       no-sd;
> +       non-removable;
> +       max-frequency = <200000000>;
> +       mmc-hs400-1_8v;
> +       mmc-hs400-enhanced-strobe;
> +       mmc-hs200-1_8v;
> +       status = "okay";
> +};
> +

Jimmy