[PATCH 1/2] arm64: dts: PinePhone Pro: describe I2c Bus 1 and IMX258 world camera
Olivier Benjamin
olivier.benjamin at bootlin.com
Sun Jan 19 14:56:59 PST 2025
Add the description of the rear/world camera (IMX258) on the PinePhone Pro
to the device dts file.
It receives commands on the I2C Bus 1 at address 0x1a and transmits data
over CSI-MIPI.
The I2C address for IMX258 can be found in the IMX258-0AQH5 Software
Reference Manual, page 24, section 2.3.1: 0b0011010 = 0x1a.
Section 3 indicates the module has 4 pairs of data lines. While 4-lane
mode is nominal, 2-lane mode should also be supported.
The pin muxing info was extracted from the PinePhone Pro schematic v1.0
as well as the RK3399 datasheet revision 1.8.
Table 2-3 in section 2.8 of the RK3399 datasheet contains the mapping
of IO functions for the SoC pins. Page 52 shows GPIO1_A0, page 54 shows
GPIO2_D4.
For I2C power, the PinePhone Pro schematic page 11 quadrants A4 and A5:
RK3399_J.AA8 and RK3399_J.Y8 get power from vcaa1v8_codec, so turn it on
The IMX258 also uses the following regulators, expected by its driver:
- vana (2.8V analog), called AVDD2V8_DVP on P.18 q.C1 and derived from
VCC1V8_S3 on P.13 q.B2
- vdig (1.2V digital core), called DVDD_DVP on P.18 q.C1 and shown on
P.18 q.D3 to be equivalent to VCC1V2_DVP derived from VCC3V3_SYS on
P.13 q.B3. Note that this regulator's voltage is inconsistently
labeled either 1.2V or 1.5V
RK3399_J.AG1 is GPIO4_A1/I2C1_SDA, RK3399_J.Y6 is GPIO4_A2/I2C1_SCL
This is the default pinctrl "i2c1_xfer" for i2c1 from rk3399-base.
For the reset (RESET) signal:
page 11 quadrant D2 | p.18 q.C3-4 | p.18 q.C2
RK3399_E.R25 -> GPIO1_A0 -> Camera_RST -> MIPI_RST0 -> IMX258.12
For the powerdown (PWDN) signal:
page 11 quadrants B4-5 | p.18 q.C2
RK3399_G.AF8 -> GPIO2_D4 -> DVP_PDN1_H -> IMX258.14
Helped-by: Dragan Simic <dsimic at manjaro.org>
Co-developed-by: Ondrej Jirman <megi at xff.cz>
Signed-off-by: Ondrej Jirman <megi at xff.cz>
Signed-off-by: Olivier Benjamin <olivier.benjamin at bootlin.com>
---
.../boot/dts/rockchip/rk3399-pinephone-pro.dts | 93 ++++++++++++++++++++++
1 file changed, 93 insertions(+)
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts b/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
index 1a44582a49fb6cb815bc441a548d38f3984c4c4e..4c059b4cda198b0f1973c7bba677ce12d37211b3 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
@@ -114,6 +114,16 @@ vcc3v3_sys: vcc3v3-sys-regulator {
vin-supply = <&vcc_sys>;
};
+ avdd2v8_dvp: avdd2v8-dvp-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "avdd2v8_dvp";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ vin-supply = <&vcc3v3_sys>;
+ };
+
vcca1v8_s3: vcc1v8-s3-regulator {
compatible = "regulator-fixed";
regulator-name = "vcca1v8_s3";
@@ -136,6 +146,16 @@ vcc1v8_codec: vcc1v8-codec-regulator {
vin-supply = <&vcc3v3_sys>;
};
+ vcc1v2_dvp: vcc1v2-dvp-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc1v2_dvp";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ vin-supply = <&vcca1v8_s3>;
+ };
+
wifi_pwrseq: sdio-wifi-pwrseq {
compatible = "mmc-pwrseq-simple";
clocks = <&rk818 1>;
@@ -314,6 +334,8 @@ vcc3v0_touch: LDO_REG2 {
vcca1v8_codec: LDO_REG3 {
regulator-name = "vcca1v8_codec";
+ regulator-always-on;
+ regulator-boot-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
@@ -422,6 +444,45 @@ regulator-state-mem {
};
};
+&i2c1 {
+ clock-frequency = <400000>;
+ pinctrl-0 = <&i2c1_xfer &cif_clkouta>;
+ assigned-clocks = <&cru SCLK_CIF_OUT>;
+ assigned-clock-rates = <24000000>;
+ status = "okay";
+
+ wcam: camera at 1a {
+ compatible = "sony,imx258";
+ reg = <0x1a>;
+ clocks = <&cru SCLK_CIF_OUT>; /* MIPI_MCLK0, derived from CIF_CLKO */
+ clock-names = "xvclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wcam_rst>;
+ /* Note: both cameras also depend on vcca1v8_codec to power the I2C bus. */
+ vif-supply = <&vcc1v8_dvp>;
+ vana-supply = <&avdd2v8_dvp>;
+ vdig-supply = <&vcc1v2_dvp>; /* DVDD_DVP is the same as VCC1V2_DVP */
+ reset-gpios = <&gpio1 RK_PA0 GPIO_ACTIVE_LOW>;
+ orientation = <1>; /* V4L2_CAMERA_ORIENTATION_BACK */
+ rotation = <270>;
+ lens-focus = <&wcam_lens>;
+
+ port {
+ wcam_out: endpoint {
+ remote-endpoint = <&mipi_in_wcam>;
+ data-lanes = <1 2 3 4>;
+ };
+ };
+ };
+
+ wcam_lens: camera-lens at c {
+ compatible = "dongwoon,dw9714";
+ reg = <0x0c>;
+ /* Same I2c bus as both cameras, depends on vcca1v8_codec for power. */
+ vcc-supply = <&vcc1v8_dvp>;
+ };
+};
+
&i2c3 {
i2c-scl-rising-time-ns = <450>;
i2c-scl-falling-time-ns = <15>;
@@ -485,6 +546,28 @@ &io_domains {
status = "okay";
};
+&isp1 {
+ status = "okay";
+
+ ports {
+ port at 0 {
+ mipi_in_wcam: endpoint at 0 {
+ reg = <0>;
+ remote-endpoint = <&wcam_out>;
+ data-lanes = <1 2 3 4>;
+ };
+ };
+ };
+};
+
+&mipi_dphy_rx0 {
+ status = "okay";
+};
+
+&isp1_mmu {
+ status = "okay";
+};
+
&mipi_dsi {
status = "okay";
clock-master;
@@ -518,6 +601,10 @@ mipi_in_panel: endpoint {
};
};
+&mipi_dsi1 {
+ status = "okay";
+};
+
&pmu_io_domains {
pmu1830-supply = <&vcc_1v8>;
status = "okay";
@@ -530,6 +617,12 @@ pwrbtn_pin: pwrbtn-pin {
};
};
+ camera {
+ wcam_rst: wcam-rst {
+ rockchip,pins = <1 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
leds {
red_led_pin: red-led-pin {
rockchip,pins = <4 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
--
2.47.1
More information about the Linux-rockchip
mailing list