[PATCH v1 2/2] arm64: dts: rockchip: Add support for rk3588s evb1 board

[Heiko Stübner]

Am Dienstag, 10. September 2024, 05:09:51 CEST schrieb Damon Ding:
> Specification:
> - Rockchip RK3588S
> - RK806-2x2pcs + DiscretePower
> - eMMC5.1 + SPI Flash
> - Micro SD Card3.0
> - 1 x Typec3.0 + 2 x USB2 HOST
> - 1 x 1Lane PCIE2.0 Connector(RC Mode)
> - Headphone output
> - Array Key(MENU/VOL+/VOP-/ESC), Reset, Power on/off Key
> - 6 x SARADC
> 
> Signed-off-by: Damon Ding <damon.ding at rock-chips.com>
> ---

[...]

> +	analog-sound {
> +		compatible = "simple-audio-card";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&hp_detect>;
> +		simple-audio-card,name = "RK3588 EVB1 Audio";
> +		simple-audio-card,aux-devs = <&amp_headphone>, <&amp_speaker>;
> +		simple-audio-card,bitclock-master = <&masterdai>;
> +		simple-audio-card,format = "i2s";
> +		simple-audio-card,frame-master = <&masterdai>;
> +		simple-audio-card,hp-det-gpio = <&gpio1 RK_PD5 GPIO_ACTIVE_LOW>;
> +		simple-audio-card,mclk-fs = <256>;
> +		simple-audio-card,pin-switches = "Headphones", "Speaker";
> +		simple-audio-card,routing =
> +			"Speaker Amplifier INL", "LOUT2",
> +			"Speaker Amplifier INR", "ROUT2",
> +			"Speaker", "Speaker Amplifier OUTL",
> +			"Speaker", "Speaker Amplifier OUTR",
> +			"Headphones Amplifier INL", "LOUT1",
> +			"Headphones Amplifier INR", "ROUT1",
> +			"Headphones", "Headphones Amplifier OUTL",
> +			"Headphones", "Headphones Amplifier OUTR",
> +			"LINPUT1", "Onboard Microphone",
> +			"RINPUT1", "Onboard Microphone",
> +			"LINPUT2", "Microphone Jack",
> +			"RINPUT2", "Microphone Jack";
> +		simple-audio-card,widgets =
> +			"Microphone", "Microphone Jack",
> +			"Microphone", "Onboard Microphone",
> +			"Headphone", "Headphones",
> +			"Speaker", "Speaker";
> +
> +		simple-audio-card,cpu {
> +			sound-dai = <&i2s0_8ch>;
> +		};
> +
> +		masterdai: simple-audio-card,codec {
> +			sound-dai = <&es8388>;
> +			system-clock-frequency = <12288000>;
> +		};
> +	};
> +
> +	amp_headphone: headphone-amplifier {
> +		compatible = "simple-audio-amplifier";
> +		enable-gpios = <&gpio4 RK_PA4 GPIO_ACTIVE_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&headphone_amplifier_en>;
> +		sound-name-prefix = "Headphones Amplifier";
> +	};
> +
> +	amp_speaker: speaker-amplifier {
> +		compatible = "simple-audio-amplifier";
> +		enable-gpios = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&speaker_amplifier_en>;
> +		sound-name-prefix = "Speaker Amplifier";
> +	};
> +
> +	backlight: backlight {

please sort nodes by node name ... so "backlight" after "analog-sound"

> +		compatible = "pwm-backlight";
> +		power-supply = <&vcc3v3_lcd_edp>;
> +		pwms = <&pwm12 0 25000 0>;
> +	};
> +
> +	combophy_avdd0v85: combophy-avdd0v85-regulator {

generally the naming convention for regulator nodes now is
regulator-* ... so regulator-combophy-avdd0v85 here
and similar for others below.


Heiko