[RESEND PATCH v3 2/2] phy: rockchip-naneng-combo: add rk3576 support
Frank Wang
frawang.cn at gmail.com
Tue Nov 5 18:13:57 PST 2024
From: Kever Yang <kever.yang at rock-chips.com>
Rockchip RK3576 integrates two naneng-combo PHY, PHY0 is used for
PCIE and SATA, PHY1 is used for PCIE, SATA and USB3.
This adds device specific data support.
Signed-off-by: Kever Yang <kever.yang at rock-chips.com>
Signed-off-by: William Wu <william.wu at rock-chips.com>
Signed-off-by: Frank Wang <frank.wang at rock-chips.com>
---
Changelog:
v3:
- add detail commit contents.
- using FIELD_PREP() instead of bit shift.
- leave a blank line after each switch break case.
v2:
- using constants macro instead of magic values.
- add more comments for PHY tuning operations.
v1:
- https://patchwork.kernel.org/project/linux-phy/patch/20241015013351.4884-2-frawang.cn@gmail.com/
.../rockchip/phy-rockchip-naneng-combphy.c | 279 ++++++++++++++++++
1 file changed, 279 insertions(+)
diff --git a/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c b/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
index 0a9989e41237f..eceb798567859 100644
--- a/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
+++ b/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
@@ -37,6 +37,10 @@
#define PHYREG8 0x1C
#define PHYREG8_SSC_EN BIT(4)
+#define PHYREG10 0x24
+#define PHYREG10_SSC_PCM_MASK GENMASK(3, 0)
+#define PHYREG10_SSC_PCM_3500PPM 7
+
#define PHYREG11 0x28
#define PHYREG11_SU_TRIM_0_7 0xF0
@@ -61,17 +65,26 @@
#define PHYREG16 0x3C
#define PHYREG16_SSC_CNT_VALUE 0x5f
+#define PHYREG17 0x40
+
#define PHYREG18 0x44
#define PHYREG18_PLL_LOOP 0x32
+#define PHYREG21 0x50
+#define PHYREG21_RX_SQUELCH_VAL 0x0D
+
#define PHYREG27 0x6C
#define PHYREG27_RX_TRIM_RK3588 0x4C
+#define PHYREG30 0x74
+
#define PHYREG32 0x7C
#define PHYREG32_SSC_MASK GENMASK(7, 4)
+#define PHYREG32_SSC_DIR_MASK GENMASK(5, 4)
#define PHYREG32_SSC_DIR_SHIFT 4
#define PHYREG32_SSC_UPWARD 0
#define PHYREG32_SSC_DOWNWARD 1
+#define PHYREG32_SSC_OFFSET_MASK GENMASK(7, 6)
#define PHYREG32_SSC_OFFSET_SHIFT 6
#define PHYREG32_SSC_OFFSET_500PPM 1
@@ -79,6 +92,7 @@
#define PHYREG33_PLL_KVCO_MASK GENMASK(4, 2)
#define PHYREG33_PLL_KVCO_SHIFT 2
#define PHYREG33_PLL_KVCO_VALUE 2
+#define PHYREG33_PLL_KVCO_VALUE_RK3576 4
struct rockchip_combphy_priv;
@@ -98,6 +112,7 @@ struct rockchip_combphy_grfcfg {
struct combphy_reg pipe_rxterm_set;
struct combphy_reg pipe_txelec_set;
struct combphy_reg pipe_txcomp_set;
+ struct combphy_reg pipe_clk_24m;
struct combphy_reg pipe_clk_25m;
struct combphy_reg pipe_clk_100m;
struct combphy_reg pipe_phymode_sel;
@@ -584,6 +599,266 @@ static const struct rockchip_combphy_cfg rk3568_combphy_cfgs = {
.combphy_cfg = rk3568_combphy_cfg,
};
+static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
+{
+ const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
+ unsigned long rate;
+ u32 val;
+
+ switch (priv->type) {
+ case PHY_TYPE_PCIE:
+ /* Set SSC downward spread spectrum */
+ val = FIELD_PREP(PHYREG32_SSC_MASK, PHYREG32_SSC_DOWNWARD);
+ rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK, val, PHYREG32);
+
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_pcie, true);
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_pcie, true);
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->con2_for_pcie, true);
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->con3_for_pcie, true);
+ break;
+
+ case PHY_TYPE_USB3:
+ /* Set SSC downward spread spectrum */
+ val = FIELD_PREP(PHYREG32_SSC_MASK, PHYREG32_SSC_DOWNWARD);
+ rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK, val, PHYREG32);
+
+ /* Enable adaptive CTLE for USB3.0 Rx */
+ val = readl(priv->mmio + PHYREG15);
+ val |= PHYREG15_CTLE_EN;
+ writel(val, priv->mmio + PHYREG15);
+
+ /* Set PLL KVCO fine tuning signals */
+ rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK, BIT(3), PHYREG33);
+
+ /* Set PLL LPF R1 to su_trim[10:7]=1001 */
+ writel(PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + PHYREG12);
+
+ /* Set PLL input clock divider 1/2 */
+ val = FIELD_PREP(PHYREG6_PLL_DIV_MASK, PHYREG6_PLL_DIV_2);
+ rockchip_combphy_updatel(priv, PHYREG6_PLL_DIV_MASK, val, PHYREG6);
+
+ /* Set PLL loop divider */
+ writel(PHYREG18_PLL_LOOP, priv->mmio + PHYREG18);
+
+ /* Set PLL KVCO to min and set PLL charge pump current to max */
+ writel(PHYREG11_SU_TRIM_0_7, priv->mmio + PHYREG11);
+
+ /* Set Rx squelch input filler bandwidth */
+ writel(PHYREG21_RX_SQUELCH_VAL, priv->mmio + PHYREG21);
+
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txcomp_sel, false);
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txelec_sel, false);
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->usb_mode_set, true);
+ break;
+
+ case PHY_TYPE_SATA:
+ /* Enable adaptive CTLE for SATA Rx */
+ val = readl(priv->mmio + PHYREG15);
+ val |= PHYREG15_CTLE_EN;
+ writel(val, priv->mmio + PHYREG15);
+
+ /* Set tx_rterm = 50 ohm and rx_rterm = 43.5 ohm */
+ val = PHYREG7_TX_RTERM_50OHM << PHYREG7_TX_RTERM_SHIFT;
+ val |= PHYREG7_RX_RTERM_44OHM << PHYREG7_RX_RTERM_SHIFT;
+ writel(val, priv->mmio + PHYREG7);
+
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_sata, true);
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_sata, true);
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->con2_for_sata, true);
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->con3_for_sata, true);
+ rockchip_combphy_param_write(priv->pipe_grf, &cfg->pipe_con0_for_sata, true);
+ rockchip_combphy_param_write(priv->pipe_grf, &cfg->pipe_con1_for_sata, true);
+ break;
+
+ default:
+ dev_err(priv->dev, "incompatible PHY type\n");
+ return -EINVAL;
+ }
+
+ rate = clk_get_rate(priv->refclk);
+
+ switch (rate) {
+ case REF_CLOCK_24MHz:
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_24m, true);
+ if (priv->type == PHY_TYPE_USB3 || priv->type == PHY_TYPE_SATA) {
+ /* Set ssc_cnt[9:0]=0101111101 & 31.5KHz */
+ val = FIELD_PREP(PHYREG15_SSC_CNT_MASK, PHYREG15_SSC_CNT_VALUE);
+ rockchip_combphy_updatel(priv, PHYREG15_SSC_CNT_MASK,
+ val, PHYREG15);
+
+ writel(PHYREG16_SSC_CNT_VALUE, priv->mmio + PHYREG16);
+ } else if (priv->type == PHY_TYPE_PCIE) {
+ /* PLL KVCO tuning fine */
+ val = FIELD_PREP(PHYREG33_PLL_KVCO_MASK, PHYREG33_PLL_KVCO_VALUE_RK3576);
+ rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
+ val, PHYREG33);
+
+ /* Set up rx_pck invert and rx msb to disable */
+ writel(0x00, priv->mmio + PHYREG27);
+
+ /*
+ * Set up SU adjust signal:
+ * su_trim[7:0], PLL KVCO adjust bits[2:0] to min
+ * su_trim[15:8], PLL LPF R1 adujst bits[9:7]=3'b011
+ * su_trim[31:24], CKDRV adjust
+ */
+ writel(0x90, priv->mmio + PHYREG11);
+ writel(0x02, priv->mmio + PHYREG12);
+ writel(0x57, priv->mmio + PHYREG14);
+
+ writel(PHYREG16_SSC_CNT_VALUE, priv->mmio + PHYREG16);
+ }
+ break;
+
+ case REF_CLOCK_25MHz:
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_25m, true);
+ break;
+
+ case REF_CLOCK_100MHz:
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_100m, true);
+ if (priv->type == PHY_TYPE_PCIE) {
+ /* gate_tx_pck_sel length select work for L1SS */
+ writel(0xc0, priv->mmio + PHYREG30);
+
+ /* PLL KVCO tuning fine */
+ val = FIELD_PREP(PHYREG33_PLL_KVCO_MASK, PHYREG33_PLL_KVCO_VALUE_RK3576);
+ rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
+ val, PHYREG33);
+
+ /* Set up rx_trim: PLL LPF C1 85pf R1 1.25kohm */
+ writel(0x4c, priv->mmio + PHYREG27);
+
+ /*
+ * Set up SU adjust signal:
+ * su_trim[7:0], PLL KVCO adjust bits[2:0] to min
+ * su_trim[15:8], bypass PLL loop divider code, and
+ * PLL LPF R1 adujst bits[9:7]=3'b101
+ * su_trim[23:16], CKRCV adjust
+ * su_trim[31:24], CKDRV adjust
+ */
+ writel(0x90, priv->mmio + PHYREG11);
+ writel(0x43, priv->mmio + PHYREG12);
+ writel(0x88, priv->mmio + PHYREG13);
+ writel(0x56, priv->mmio + PHYREG14);
+ } else if (priv->type == PHY_TYPE_SATA) {
+ /* downward spread spectrum +500ppm */
+ val = FIELD_PREP(PHYREG32_SSC_DIR_MASK, PHYREG32_SSC_DOWNWARD);
+ val |= FIELD_PREP(PHYREG32_SSC_OFFSET_MASK, PHYREG32_SSC_OFFSET_500PPM);
+ rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK, val, PHYREG32);
+
+ /* ssc ppm adjust to 3500ppm */
+ rockchip_combphy_updatel(priv, PHYREG10_SSC_PCM_MASK,
+ PHYREG10_SSC_PCM_3500PPM,
+ PHYREG10);
+ }
+ break;
+
+ default:
+ dev_err(priv->dev, "Unsupported rate: %lu\n", rate);
+ return -EINVAL;
+ }
+
+ if (priv->ext_refclk) {
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_ext, true);
+ if (priv->type == PHY_TYPE_PCIE && rate == REF_CLOCK_100MHz) {
+ val = FIELD_PREP(PHYREG33_PLL_KVCO_MASK, PHYREG33_PLL_KVCO_VALUE_RK3576);
+ rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
+ val, PHYREG33);
+
+ /* Set up rx_trim: PLL LPF C1 85pf R1 2.5kohm */
+ writel(0x0c, priv->mmio + PHYREG27);
+
+ /*
+ * Set up SU adjust signal:
+ * su_trim[7:0], PLL KVCO adjust bits[2:0] to min
+ * su_trim[15:8], bypass PLL loop divider code, and
+ * PLL LPF R1 adujst bits[9:7]=3'b101.
+ * su_trim[23:16], CKRCV adjust
+ * su_trim[31:24], CKDRV adjust
+ */
+ writel(0x90, priv->mmio + PHYREG11);
+ writel(0x43, priv->mmio + PHYREG12);
+ writel(0x88, priv->mmio + PHYREG13);
+ writel(0x56, priv->mmio + PHYREG14);
+ }
+ }
+
+ if (priv->enable_ssc) {
+ val = readl(priv->mmio + PHYREG8);
+ val |= PHYREG8_SSC_EN;
+ writel(val, priv->mmio + PHYREG8);
+
+ if (priv->type == PHY_TYPE_PCIE && rate == REF_CLOCK_24MHz) {
+ /* Set PLL loop divider */
+ writel(0x00, priv->mmio + PHYREG17);
+ writel(PHYREG18_PLL_LOOP, priv->mmio + PHYREG18);
+
+ /* Set up rx_pck invert and rx msb to disable */
+ writel(0x00, priv->mmio + PHYREG27);
+
+ /*
+ * Set up SU adjust signal:
+ * su_trim[7:0], PLL KVCO adjust bits[2:0] to min
+ * su_trim[15:8], PLL LPF R1 adujst bits[9:7]=3'b101
+ * su_trim[23:16], CKRCV adjust
+ * su_trim[31:24], CKDRV adjust
+ */
+ writel(0x90, priv->mmio + PHYREG11);
+ writel(0x02, priv->mmio + PHYREG12);
+ writel(0x08, priv->mmio + PHYREG13);
+ writel(0x57, priv->mmio + PHYREG14);
+ writel(0x40, priv->mmio + PHYREG15);
+
+ writel(PHYREG16_SSC_CNT_VALUE, priv->mmio + PHYREG16);
+
+ val = FIELD_PREP(PHYREG33_PLL_KVCO_MASK, PHYREG33_PLL_KVCO_VALUE_RK3576);
+ writel(val, priv->mmio + PHYREG33);
+ }
+ }
+
+ return 0;
+}
+
+static const struct rockchip_combphy_grfcfg rk3576_combphy_grfcfgs = {
+ /* pipe-phy-grf */
+ .pcie_mode_set = { 0x0000, 5, 0, 0x00, 0x11 },
+ .usb_mode_set = { 0x0000, 5, 0, 0x00, 0x04 },
+ .pipe_rxterm_set = { 0x0000, 12, 12, 0x00, 0x01 },
+ .pipe_txelec_set = { 0x0004, 1, 1, 0x00, 0x01 },
+ .pipe_txcomp_set = { 0x0004, 4, 4, 0x00, 0x01 },
+ .pipe_clk_24m = { 0x0004, 14, 13, 0x00, 0x00 },
+ .pipe_clk_25m = { 0x0004, 14, 13, 0x00, 0x01 },
+ .pipe_clk_100m = { 0x0004, 14, 13, 0x00, 0x02 },
+ .pipe_phymode_sel = { 0x0008, 1, 1, 0x00, 0x01 },
+ .pipe_rate_sel = { 0x0008, 2, 2, 0x00, 0x01 },
+ .pipe_rxterm_sel = { 0x0008, 8, 8, 0x00, 0x01 },
+ .pipe_txelec_sel = { 0x0008, 12, 12, 0x00, 0x01 },
+ .pipe_txcomp_sel = { 0x0008, 15, 15, 0x00, 0x01 },
+ .pipe_clk_ext = { 0x000c, 9, 8, 0x02, 0x01 },
+ .pipe_phy_status = { 0x0034, 6, 6, 0x01, 0x00 },
+ .con0_for_pcie = { 0x0000, 15, 0, 0x00, 0x1000 },
+ .con1_for_pcie = { 0x0004, 15, 0, 0x00, 0x0000 },
+ .con2_for_pcie = { 0x0008, 15, 0, 0x00, 0x0101 },
+ .con3_for_pcie = { 0x000c, 15, 0, 0x00, 0x0200 },
+ .con0_for_sata = { 0x0000, 15, 0, 0x00, 0x0129 },
+ .con1_for_sata = { 0x0004, 15, 0, 0x00, 0x0000 },
+ .con2_for_sata = { 0x0008, 15, 0, 0x00, 0x80c1 },
+ .con3_for_sata = { 0x000c, 15, 0, 0x00, 0x0407 },
+ /* php-grf */
+ .pipe_con0_for_sata = { 0x001C, 2, 0, 0x00, 0x2 },
+ .pipe_con1_for_sata = { 0x0020, 2, 0, 0x00, 0x2 },
+};
+
+static const struct rockchip_combphy_cfg rk3576_combphy_cfgs = {
+ .num_phys = 2,
+ .phy_ids = {
+ 0x2b050000,
+ 0x2b060000
+ },
+ .grfcfg = &rk3576_combphy_grfcfgs,
+ .combphy_cfg = rk3576_combphy_cfg,
+};
+
static int rk3588_combphy_cfg(struct rockchip_combphy_priv *priv)
{
const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
@@ -775,6 +1050,10 @@ static const struct of_device_id rockchip_combphy_of_match[] = {
.compatible = "rockchip,rk3568-naneng-combphy",
.data = &rk3568_combphy_cfgs,
},
+ {
+ .compatible = "rockchip,rk3576-naneng-combphy",
+ .data = &rk3576_combphy_cfgs,
+ },
{
.compatible = "rockchip,rk3588-naneng-combphy",
.data = &rk3588_combphy_cfgs,
--
2.25.1
More information about the Linux-rockchip
mailing list