[PATCH v4 1/6] arm64: dts: rockchip: add thermal zones information on RK3588

[Dragan Simic]

Hello Alexey,

Thanks for submitting the v4 of this series!  Please, see a couple
of my comments below.

On 2024-05-06 11:36, Alexey Charkov wrote:
> This includes the necessary device tree data to allow thermal
> monitoring on RK3588(s) using the on-chip TSADC device, along with
> trip points for automatic thermal management.
> 
> Each of the CPU clusters (one for the little cores and two for
> the big cores) get a passive cooling trip point at 85C, which
> will trigger DVFS throttling of the respective cluster upon
> reaching a high temperature condition.
> 
> All zones also have a critical trip point at 115C, which will
> trigger a reset.
> 
> Signed-off-by: Alexey Charkov <alchark at gmail.com>
> ---
>  arch/arm64/boot/dts/rockchip/rk3588s.dtsi | 147 
> ++++++++++++++++++++++++++++++
>  1 file changed, 147 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
> b/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
> index 6ac5ac8b48ab..ef06c1f742e8 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
> +++ b/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
> @@ -10,6 +10,7 @@
>  #include <dt-bindings/reset/rockchip,rk3588-cru.h>
>  #include <dt-bindings/phy/phy.h>
>  #include <dt-bindings/ata/ahci.h>
> +#include <dt-bindings/thermal/thermal.h>
> 
>  / {
>  	compatible = "rockchip,rk3588";
> @@ -2368,6 +2369,152 @@ pwm15: pwm at febf0030 {
>  		status = "disabled";
>  	};
> 
> +	thermal_zones: thermal-zones {
> +		/* sensor near the center of the SoC */
> +		package_thermal: package-thermal {
> +			polling-delay-passive = <0>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&tsadc 0>;
> +
> +			trips {
> +				package_crit: package-crit {
> +					temperature = <115000>;
> +					hysteresis = <0>;
> +					type = "critical";
> +				};
> +			};
> +		};
> +
> +		/* sensor between A76 cores 0 and 1 */
> +		bigcore0_thermal: bigcore0-thermal {
> +			polling-delay-passive = <100>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&tsadc 1>;
> +
> +			trips {
> +				bigcore0_alert: bigcore0-alert {
> +					temperature = <85000>;
> +					hysteresis = <2000>;
> +					type = "passive";
> +				};

Doesn't removing the second passive trip, which was present in the v3,
result in confusing the IPA governor?

> +				bigcore0_crit: bigcore0-crit {
> +					temperature = <115000>;
> +					hysteresis = <0>;
> +					type = "critical";
> +				};
> +			};
> +			cooling-maps {
> +				map0 {
> +					trip = <&bigcore0_alert>;
> +					cooling-device =
> +						<&cpu_b0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu_b1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +				};
> +			};
> +		};
> +
> +		/* sensor between A76 cores 2 and 3 */
> +		bigcore2_thermal: bigcore2-thermal {
> +			polling-delay-passive = <100>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&tsadc 2>;
> +
> +			trips {
> +				bigcore2_alert: bigcore2-alert {
> +					temperature = <85000>;
> +					hysteresis = <2000>;
> +					type = "passive";
> +				};

The same question about the second passive trip applies here, and to
all similar cases below.

> +				bigcore2_crit: bigcore2-crit {
> +					temperature = <115000>;
> +					hysteresis = <0>;
> +					type = "critical";
> +				};
> +			};
> +			cooling-maps {
> +				map0 {
> +					trip = <&bigcore2_alert>;
> +					cooling-device =
> +						<&cpu_b2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu_b3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +				};
> +			};
> +		};
> +
> +		/* sensor between the four A55 cores */
> +		little_core_thermal: littlecore-thermal {
> +			polling-delay-passive = <100>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&tsadc 3>;
> +
> +			trips {
> +				littlecore_alert: littlecore-alert {
> +					temperature = <85000>;
> +					hysteresis = <2000>;
> +					type = "passive";
> +				};
> +				littlecore_crit: littlecore-crit {
> +					temperature = <115000>;
> +					hysteresis = <0>;
> +					type = "critical";
> +				};
> +			};
> +			cooling-maps {
> +				map0 {
> +					trip = <&littlecore_alert>;
> +					cooling-device =
> +						<&cpu_l0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu_l1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu_l2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu_l3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +				};
> +			};
> +		};
> +
> +		/* sensor near the PD_CENTER power domain */
> +		center_thermal: center-thermal {
> +			polling-delay-passive = <0>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&tsadc 4>;
> +
> +			trips {
> +				center_crit: center-crit {
> +					temperature = <115000>;
> +					hysteresis = <0>;
> +					type = "critical";
> +				};
> +			};
> +		};
> +
> +		gpu_thermal: gpu-thermal {
> +			polling-delay-passive = <0>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&tsadc 5>;
> +
> +			trips {
> +				gpu_crit: gpu-crit {
> +					temperature = <115000>;
> +					hysteresis = <0>;
> +					type = "critical";
> +				};
> +			};
> +		};
> +
> +		npu_thermal: npu-thermal {
> +			polling-delay-passive = <0>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&tsadc 6>;
> +
> +			trips {
> +				npu_crit: npu-crit {
> +					temperature = <115000>;
> +					hysteresis = <0>;
> +					type = "critical";
> +				};
> +			};
> +		};
> +	};
> +
>  	tsadc: tsadc at fec00000 {
>  		compatible = "rockchip,rk3588-tsadc";
>  		reg = <0x0 0xfec00000 0x0 0x400>;