[PATCH v2 2/4] arm64: dts: rockchip: enable temperature driven fan control on Rock 5B

[Dragan Simic]

Hello Alexey,

Some notes below, please have a look.

On 2024-01-30 19:21, Alexey Charkov wrote:
> This enables thermal monitoring on Radxa Rock 5B and links the PWM
> fan as an active cooling device managed automatically by the thermal
> subsystem, with a target SoC temperature of 65C and a minimum-spin
> interval from 55C to 65C to ensure airflow when the system gets warm

I'd suggest that you replace "temperature driven fan control" with
"active cooling" in the patch subject.  More concise and reads better.

> Acked-by: Daniel Lezcano <daniel.lezcano at linaro.org>
> Signed-off-by: Alexey Charkov <alchark at gmail.com>
> ---
>  arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts | 34 
> ++++++++++++++++++++++++-
>  1 file changed, 33 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts
> b/arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts
> index a0e303c3a1dc..b485edeef876 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts
> +++ b/arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts
> @@ -52,7 +52,7 @@ led_rgb_b {
> 
>  	fan: pwm-fan {
>  		compatible = "pwm-fan";
> -		cooling-levels = <0 95 145 195 255>;
> +		cooling-levels = <0 120 150 180 210 240 255>;
>  		fan-supply = <&vcc5v0_sys>;
>  		pwms = <&pwm1 0 50000 0>;
>  		#cooling-cells = <2>;
> @@ -173,6 +173,34 @@ &cpu_l3 {
>  	cpu-supply = <&vdd_cpu_lit_s0>;
>  };
> 
> +&package_thermal {
> +	polling-delay = <1000>;
> +
> +	trips {
> +		package_fan0: package-fan0 {
> +			temperature = <55000>;
> +			hysteresis = <2000>;
> +			type = "active";
> +		};
> +		package_fan1: package-fan1 {
> +			temperature = <65000>;
> +			hysteresis = <2000>;
> +			type = "active";
> +		};
> +	};
> +
> +	cooling-maps {
> +		map0 {

Should be "map1" instead of "map0".  There's already "map0"
defined for "package_thermal" in the RK3588(s) dtsi file.

> +			trip = <&package_fan0>;
> +			cooling-device = <&fan THERMAL_NO_LIMIT 1>;
> +		};
> +		map1 {

Should be "map2" instead of "map1".

> +			trip = <&package_fan1>;
> +			cooling-device = <&fan 1 THERMAL_NO_LIMIT>;

Should be "cooling-device = <&fan 2 THERMAL_NO_LIMIT>;"
(i.e., "2 THERMAL_NO_LIMIT" instead of "1 THERMAL_NO_LIMIT").

The first fan speed is already covered by the first cooling map.
The second cooling map takes over from the second fan speed.

> +		};
> +	};
> +};
> +
>  &i2c0 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&i2c0m2_xfer>;
> @@ -731,6 +759,10 @@ regulator-state-mem {
>  	};
>  };
> 
> +&tsadc {
> +	status = "okay";
> +};
> +
>  &uart2 {
>  	pinctrl-0 = <&uart2m0_xfer>;
>  	status = "okay";