[PATCH 21/38] phy: rockchip: inno-usb2: add usb2 phy support for rk3562

[Kever Yang]

From: Frank Wang <frank.wang at rock-chips.com>

RK3652 has one USB2.0 PHY with two ports, the OTG port support OTG
and BC1.2, the SoC provide USB GRF and APB to access the registers.

This adds vbus detection function control and make the below tuning
to enhance the usb2-phy SQ for RK3562 SoC.
 - enable pre-emphasis during non-chirp phase
 - set HS eye height to 425mv
 - turn off differential receiver by default to save power

Signed-off-by: Frank Wang <frank.wang at rock-chips.com>
Signed-off-by: William Wu <william.wu at rock-chips.com>
Signed-off-by: Kever Yang <kever.yang at rock-chips.com>
---

 drivers/phy/rockchip/phy-rockchip-inno-usb2.c | 49 +++++++++++++++++++
 1 file changed, 49 insertions(+)

diff --git a/drivers/phy/rockchip/phy-rockchip-inno-usb2.c b/drivers/phy/rockchip/phy-rockchip-inno-usb2.c
index 96f3d868a526..946dd7ac409d 100644
--- a/drivers/phy/rockchip/phy-rockchip-inno-usb2.c
+++ b/drivers/phy/rockchip/phy-rockchip-inno-usb2.c
@@ -1892,6 +1892,54 @@ static const struct rockchip_usb2phy_cfg rk3399_phy_cfgs[] = {
 	{ /* sentinel */ }
 };
 
+static const struct rockchip_usb2phy_cfg rk3562_phy_cfgs[] = {
+	{
+		.reg = 0xff740000,
+		.num_ports	= 2,
+		.clkout_ctl	= { 0x0108, 4, 4, 1, 0 },
+		.port_cfgs	= {
+			[USB2PHY_PORT_OTG] = {
+				.phy_sus	= { 0x0100, 8, 0, 0, 0x1d1 },
+				.bvalid_det_en	= { 0x0110, 2, 2, 0, 1 },
+				.bvalid_det_st	= { 0x0114, 2, 2, 0, 1 },
+				.bvalid_det_clr = { 0x0118, 2, 2, 0, 1 },
+				.idfall_det_en	= { 0x0110, 5, 5, 0, 1 },
+				.idfall_det_st	= { 0x0114, 5, 5, 0, 1 },
+				.idfall_det_clr = { 0x0118, 5, 5, 0, 1 },
+				.idrise_det_en	= { 0x0110, 4, 4, 0, 1 },
+				.idrise_det_st	= { 0x0114, 4, 4, 0, 1 },
+				.idrise_det_clr = { 0x0118, 4, 4, 0, 1 },
+				.ls_det_en	= { 0x0110, 0, 0, 0, 1 },
+				.ls_det_st	= { 0x0114, 0, 0, 0, 1 },
+				.ls_det_clr	= { 0x0118, 0, 0, 0, 1 },
+				.utmi_avalid	= { 0x0120, 10, 10, 0, 1 },
+				.utmi_bvalid	= { 0x0120, 9, 9, 0, 1 },
+				.utmi_ls	= { 0x0120, 5, 4, 0, 1 },
+			},
+			[USB2PHY_PORT_HOST] = {
+				.phy_sus	= { 0x0104, 8, 0, 0x1d2, 0x1d1 },
+				.ls_det_en	= { 0x0110, 1, 1, 0, 1 },
+				.ls_det_st	= { 0x0114, 1, 1, 0, 1 },
+				.ls_det_clr	= { 0x0118, 1, 1, 0, 1 },
+				.utmi_ls	= { 0x0120, 17, 16, 0, 1 },
+				.utmi_hstdet	= { 0x0120, 19, 19, 0, 1 }
+			}
+		},
+		.chg_det = {
+			.cp_det		= { 0x0120, 24, 24, 0, 1 },
+			.dcp_det	= { 0x0120, 23, 23, 0, 1 },
+			.dp_det		= { 0x0120, 25, 25, 0, 1 },
+			.idm_sink_en	= { 0x0108, 8, 8, 0, 1 },
+			.idp_sink_en	= { 0x0108, 7, 7, 0, 1 },
+			.idp_src_en	= { 0x0108, 9, 9, 0, 1 },
+			.rdm_pdwn_en	= { 0x0108, 10, 10, 0, 1 },
+			.vdm_src_en	= { 0x0108, 12, 12, 0, 1 },
+			.vdp_src_en	= { 0x0108, 11, 11, 0, 1 },
+		},
+	},
+	{ /* sentinel */ }
+};
+
 static const struct rockchip_usb2phy_cfg rk3568_phy_cfgs[] = {
 	{
 		.reg = 0xfe8a0000,
@@ -2210,6 +2258,7 @@ static const struct of_device_id rockchip_usb2phy_dt_match[] = {
 	{ .compatible = "rockchip,rk3328-usb2phy", .data = &rk3328_phy_cfgs },
 	{ .compatible = "rockchip,rk3366-usb2phy", .data = &rk3366_phy_cfgs },
 	{ .compatible = "rockchip,rk3399-usb2phy", .data = &rk3399_phy_cfgs },
+	{ .compatible = "rockchip,rk3562-usb2phy", .data = &rk3562_phy_cfgs },
 	{ .compatible = "rockchip,rk3568-usb2phy", .data = &rk3568_phy_cfgs },
 	{ .compatible = "rockchip,rk3576-usb2phy", .data = &rk3576_phy_cfgs },
 	{ .compatible = "rockchip,rk3588-usb2phy", .data = &rk3588_phy_cfgs },
-- 
2.25.1