[PATCH] arm64: dts: rockchip: rk3588s-orangepi-5: add USB-C support

[Heiko Stübner]

Hi Jimmy,

Am Montag, 15. April 2024, 19:03:31 CEST schrieb Jimmy Hon:
> Add support for using the Orange Pi 5 USB-C port for USB in OHCI, EHCI
> or XHCI mode. Displayport AltMode is not yet supported.
> 
> Signed-off-by: Jimmy Hon <honyuenkwun at gmail.com>

[...]

> +	usbc0: usb-typec at 22 {
> +		compatible = "fcs,fusb302";
> +		reg = <0x22>;
> +		interrupt-parent = <&gpio0>;
> +		interrupts = <RK_PD3 IRQ_TYPE_LEVEL_LOW>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&usbc0_int>;
> +		vbus-supply = <&vbus_typec>;
> +		status = "okay";
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port at 0 {
> +				reg = <0>;
> +
> +				usbc0_role_sw: endpoint at 0 {
> +					remote-endpoint = <&dwc3_0_role_switch>;
> +				};
> +			};
> +		};

as you already saw from the mail of Rob's bot, this does not belong here
in the mainline kernel.


> +		usb_con: connector {
> +			compatible = "usb-c-connector";
> +			label = "USB-C";
> +			data-role = "dual";
> +			op-sink-microwatt = <1000000>;
> +			power-role = "dual";
> +			sink-pdos =
> +				<PDO_FIXED(5000, 1000, PDO_FIXED_USB_COMM)>;
> +			source-pdos =
> +				<PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
> +			try-power-role = "source";
> +
> +			ports {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				port at 0 {
> +					reg = <0>;
> +
> +					usbc0_orien_sw: endpoint {
> +						remote-endpoint = <&usbdp_phy0_orientation_switch>;
> +					};
> +				};
> +
> +				port at 1 {
> +					reg = <1>;
> +
> +					dp_altmode_mux: endpoint {
> +						remote-endpoint = <&usbdp_phy0_dp_altmode_mux>;
> +					};
> +				};

these ports also look like they do not follow the binding.
The type-c-connector binding specifies the ports as
- port at 1: High Speed (HS) data bus to the connector
- port at 2: Siper Speed (SS) data bus to the connector
- port at 3: Sideband Use (SBU) - the alternate mode


> +			};
> +		};
> +	};
> +
>  	hym8563: rtc at 51 {
>  		compatible = "haoyu,hym8563";
>  		reg = <0x51>;
> @@ -625,6 +684,14 @@ &tsadc {
>  	status = "okay";
>  };
>  
> +&u2phy0 {
> +	status = "okay";
> +};
> +
> +&u2phy0_otg {
> +	status = "okay";
> +};
> +
>  &u2phy2 {
>  	status = "okay";
>  };
> @@ -646,6 +713,29 @@ &uart2 {
>  	status = "okay";
>  };
>  
> +&usbdp_phy0 {
> +	mode-switch;
> +	orientation-switch;
> +	sbu1-dc-gpios = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>;
> +	sbu2-dc-gpios = <&gpio4 RK_PA7 GPIO_ACTIVE_HIGH>;
> +	status = "okay";
> +
> +	port {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		usbdp_phy0_orientation_switch: endpoint at 0 {
> +			reg = <0>;
> +			remote-endpoint = <&usbc0_orien_sw>;
> +		};
> +
> +		usbdp_phy0_dp_altmode_mux: endpoint at 1 {
> +			reg = <1>;
> +			remote-endpoint = <&dp_altmode_mux>;
> +		};
> +	};
> +};
> +
>  &usb_host0_ehci {
>  	status = "okay";
>  };
> @@ -654,6 +744,22 @@ &usb_host0_ohci {
>  	status = "okay";
>  };
>  
> +&usb_host0_xhci {
> +	dr_mode = "otg";
> +	usb-role-switch;
> +	status = "okay";
> +
> +	port {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		dwc3_0_role_switch: endpoint at 0 {
> +			reg = <0>;

this only has one endpoint, so you should be able to live without the @0
and the reg and could also drop the #address-cells + #size-cells above?

> +			remote-endpoint = <&usbc0_role_sw>;
> +		};
> +	};
> +};
> +
>  &usb_host1_ehci {
>  	status = "okay";
>  };
> 


Heiko