[PATCH v5 08/10] arm64: dts: rockchip: add USB3 to rk3588-evb1

Sebastian Reichel sebastian.reichel at collabora.com
Mon Apr 8 15:50:35 PDT 2024


Add support for the board's USB3 connectors. It has 1x USB Type-A
and 1x USB Type-C.

Signed-off-by: Sebastian Reichel <sebastian.reichel at collabora.com>
---
 .../boot/dts/rockchip/rk3588-evb1-v10.dts     | 143 ++++++++++++++++++
 1 file changed, 143 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3588-evb1-v10.dts b/arch/arm64/boot/dts/rockchip/rk3588-evb1-v10.dts
index de30c2632b8e..c3746d3a9b1d 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588-evb1-v10.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3588-evb1-v10.dts
@@ -9,6 +9,7 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/usb/pd.h>
 #include "rk3588.dtsi"
 
 / {
@@ -224,6 +225,18 @@ vcc5v0_usb: vcc5v0-usb-regulator {
 		regulator-max-microvolt = <5000000>;
 		vin-supply = <&vcc5v0_usbdcin>;
 	};
+
+	vbus5v0_typec: vbus5v0-typec {
+		compatible = "regulator-fixed";
+		regulator-name = "vbus5v0_typec";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio4 RK_PD0 GPIO_ACTIVE_HIGH>;
+		vin-supply = <&vcc5v0_usb>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&typec5v_pwren>;
+	};
 };
 
 &combphy0_ps {
@@ -284,6 +297,56 @@ &gmac0_rgmii_clk
 &i2c2 {
 	status = "okay";
 
+	usbc0: usb-typec at 22 {
+		compatible = "fcs,fusb302";
+		reg = <0x22>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <RK_PB4 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usbc0_int>;
+		vbus-supply = <&vbus5v0_typec>;
+		status = "okay";
+
+		usb_con: connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			data-role = "dual";
+			power-role = "dual";
+			try-power-role = "source";
+			op-sink-microwatt = <1000000>;
+			sink-pdos =
+				<PDO_FIXED(5000, 1000, PDO_FIXED_USB_COMM)>;
+			source-pdos =
+				<PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port at 0 {
+					reg = <0>;
+					usbc0_orien_sw: endpoint {
+						remote-endpoint = <&usbdp_phy0_orientation_switch>;
+					};
+				};
+
+				port at 1 {
+					reg = <1>;
+					usbc0_role_sw: endpoint {
+						remote-endpoint = <&dwc3_0_role_switch>;
+					};
+				};
+
+				port at 2 {
+					reg = <2>;
+					dp_altmode_mux: endpoint {
+						remote-endpoint = <&usbdp_phy0_dp_altmode_mux>;
+					};
+				};
+			};
+		};
+	};
+
 	hym8563: rtc at 51 {
 		compatible = "haoyu,hym8563";
 		reg = <0x51>;
@@ -410,6 +473,16 @@ vcc5v0_host_en: vcc5v0-host-en {
 			rockchip,pins = <4 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 	};
+
+	usb-typec {
+		usbc0_int: usbc0-int {
+			rockchip,pins = <3 RK_PB4 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		typec5v_pwren: typec5v-pwren {
+			rockchip,pins = <4 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
 };
 
 &pwm2 {
@@ -1041,6 +1114,22 @@ &sata0 {
 	status = "okay";
 };
 
+&u2phy0 {
+	status = "okay";
+};
+
+&u2phy0_otg {
+	status = "okay";
+};
+
+&u2phy1 {
+	status = "okay";
+};
+
+&u2phy1_otg {
+	status = "okay";
+};
+
 &u2phy2 {
 	status = "okay";
 };
@@ -1079,3 +1168,57 @@ &usb_host1_ehci {
 &usb_host1_ohci {
 	status = "okay";
 };
+
+&usbdp_phy0 {
+	orientation-switch;
+	mode-switch;
+	sbu1-dc-gpios = <&gpio4 RK_PA6 GPIO_ACTIVE_HIGH>;
+	sbu2-dc-gpios = <&gpio4 RK_PA7 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+
+	port {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		usbdp_phy0_orientation_switch: endpoint at 0 {
+			reg = <0>;
+			remote-endpoint = <&usbc0_orien_sw>;
+		};
+
+		usbdp_phy0_dp_altmode_mux: endpoint at 1 {
+			reg = <1>;
+			remote-endpoint = <&dp_altmode_mux>;
+		};
+	};
+};
+
+&usbdp_phy1 {
+	/*
+	 * USBDP PHY1 is wired to a female USB3 Type-A connector. Additionally
+	 * the differential pairs 2+3 and the aux channel are wired to a RTD2166,
+	 * which converts the DP signal into VGA. This is exposed on the
+	 * board via a female VGA connector.
+	 */
+	rockchip,dp-lane-mux = <2 3>;
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	dr_mode = "otg";
+	usb-role-switch;
+	status = "okay";
+
+	port {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		dwc3_0_role_switch: endpoint at 0 {
+			reg = <0>;
+			remote-endpoint = <&usbc0_role_sw>;
+		};
+	};
+};
+
+&usb_host1_xhci {
+	dr_mode = "host";
+	status = "okay";
+};
-- 
2.43.0




More information about the Linux-rockchip mailing list