[PATCH V4 5/6] arm64: dts: rockchip: Update powkiddy,rgb30 include to rk2023 DTSI
Chris Morgan
macroalpha82 at gmail.com
Fri Nov 17 12:25:35 PST 2023
From: Chris Morgan <macromorgan at hotmail.com>
The Powkiddy RGB30 device is similar to the Anbernic RGxx3 series,
however there are several differences which require deleting nodes in
order to properly define the hardware. This was deemed unacceptable
for the RK2023, so instead create a common include file for the
Powkiddy RGB30 and the Powkiddy RK2023. The only notable difference
between these Powkiddy devices are the panel in use, the device
name, and the PLL_VPLL frequency necessary to support the different
panels.
Since the RK2023 was released on the market first, name the common
include file after it.
Signed-off-by: Chris Morgan <macromorgan at hotmail.com>
---
.../dts/rockchip/rk3566-powkiddy-rgb30.dts | 154 +--
.../dts/rockchip/rk3566-powkiddy-rk2023.dtsi | 875 ++++++++++++++++++
2 files changed, 891 insertions(+), 138 deletions(-)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-powkiddy-rk2023.dtsi
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-powkiddy-rgb30.dts b/arch/arm64/boot/dts/rockchip/rk3566-powkiddy-rgb30.dts
index 1ead3c5c24b3..0ac64f043b80 100644
--- a/arch/arm64/boot/dts/rockchip/rk3566-powkiddy-rgb30.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3566-powkiddy-rgb30.dts
@@ -5,67 +5,11 @@
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/linux-event-codes.h>
#include <dt-bindings/pinctrl/rockchip.h>
-#include "rk3566-anbernic-rg353x.dtsi"
+#include "rk3566-powkiddy-rk2023.dtsi"
/ {
model = "RGB30";
compatible = "powkiddy,rgb30", "rockchip,rk3566";
-
- aliases {
- mmc1 = &sdmmc0;
- mmc2 = &sdmmc1;
- mmc3 = &sdmmc2;
- };
-
- battery: battery {
- compatible = "simple-battery";
- charge-full-design-microamp-hours = <3151000>;
- charge-term-current-microamp = <300000>;
- constant-charge-current-max-microamp = <2000000>;
- constant-charge-voltage-max-microvolt = <4250000>;
- factory-internal-resistance-micro-ohms = <117000>;
- voltage-max-design-microvolt = <4172000>;
- voltage-min-design-microvolt = <3400000>;
-
- ocv-capacity-celsius = <20>;
- ocv-capacity-table-0 = <4172000 100>, <4092000 95>, <4035000 90>, <3990000 85>,
- <3939000 80>, <3895000 75>, <3852000 70>, <3807000 65>,
- <3762000 60>, <3713000 55>, <3672000 50>, <3647000 45>,
- <3629000 40>, <3613000 35>, <3598000 30>, <3578000 25>,
- <3550000 20>, <3519000 15>, <3479000 10>, <3438000 5>,
- <3400000 0>;
- };
-
- /*
- * Channels reversed for speakers. Headphones automatically switch via hardware when
- * detected with no ability to control output in software. Headphones appear to be mono
- * (each output channel receives all audio). No microphone support on 3.5mm jack.
- */
- sound {
- compatible = "simple-audio-card";
- simple-audio-card,name = "rk817_ext";
- simple-audio-card,format = "i2s";
- simple-audio-card,mclk-fs = <256>;
- simple-audio-card,widgets =
- "Headphone", "Headphones";
- simple-audio-card,routing =
- "Headphones", "HPOL",
- "Headphones", "HPOR";
-
- simple-audio-card,codec {
- sound-dai = <&rk817>;
- };
-
- simple-audio-card,cpu {
- sound-dai = <&i2s1_8ch>;
- };
- };
-};
-
-/delete-node/ &adc_keys;
-
-&chosen {
- /delete-property/ stdout-path;
};
&cru {
@@ -75,87 +19,21 @@ &cru {
<200000000>, <292500000>;
};
-&gpio_keys_control {
- button-r1 {
- gpios = <&gpio3 RK_PB3 GPIO_ACTIVE_LOW>;
- label = "TR";
- linux,code = <BTN_TR>;
- };
-
- button-r2 {
- gpios = <&gpio3 RK_PB4 GPIO_ACTIVE_LOW>;
- label = "TR2";
- linux,code = <BTN_TR2>;
- };
-};
-
-/delete-node/ &{/i2c at fdd40000/regulator at 40};
-
-&i2c0 {
- vdd_cpu: regulator at 1c {
- compatible = "tcs,tcs4525";
- reg = <0x1c>;
- fcs,suspend-voltage-selector = <1>;
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <712500>;
- regulator-max-microvolt = <1390000>;
- regulator-name = "vdd_cpu";
- regulator-ramp-delay = <2300>;
- vin-supply = <&vcc_sys>;
- regulator-state-mem {
- regulator-off-in-suspend;
+&dsi0 {
+ panel: panel at 0 {
+ compatible = "powkiddy,rgb30-panel";
+ reg = <0>;
+ backlight = <&backlight>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_rst>;
+ reset-gpios = <&gpio4 RK_PA0 GPIO_ACTIVE_LOW>;
+ vcc-supply = <&vcc3v3_lcd0_n>;
+ iovcc-supply = <&vcc3v3_lcd0_n>;
+
+ port {
+ mipi_in_panel: endpoint {
+ remote-endpoint = <&mipi_out_panel>;
+ };
};
};
};
-
-/*
- * Device has 2 red LEDs instead of an amber and a red. Relabel LEDs as
- * red_led0 and red_led1.
- */
-/delete-node/ &{/pwm-leds/led-1};
-/delete-node/ &{/pwm-leds/led-2};
-
-&leds {
- red_led0: led-1 {
- color = <LED_COLOR_ID_RED>;
- function = LED_FUNCTION_CHARGING;
- max-brightness = <255>;
- pwms = <&pwm7 0 25000 0>;
- };
-
- red_led1: led-2 {
- color = <LED_COLOR_ID_RED>;
- default-state = "off";
- function = LED_FUNCTION_STATUS;
- max-brightness = <255>;
- pwms = <&pwm0 0 25000 0>;
- };
-};
-
-&panel {
- compatible = "powkiddy,rgb30-panel";
- vcc-supply = <&vcc3v3_lcd0_n>;
- iovcc-supply = <&vcc3v3_lcd0_n>;
- /delete-property/ vdd-supply;
-};
-
-&pwm5 {
- status = "disabled";
-};
-
-&rk817 {
- rk817_charger: charger {
- monitored-battery = <&battery>;
- rockchip,resistor-sense-micro-ohms = <10000>;
- rockchip,sleep-enter-current-microamp = <300000>;
- rockchip,sleep-filter-current-microamp = <100000>;
- };
-};
-
-/* There is no UART header visible on the board for this device. */
-&uart2 {
- status = "disabled";
-};
-
-/delete-node/ &vibrator;
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-powkiddy-rk2023.dtsi b/arch/arm64/boot/dts/rockchip/rk3566-powkiddy-rk2023.dtsi
new file mode 100644
index 000000000000..0fa8f06f94cd
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-powkiddy-rk2023.dtsi
@@ -0,0 +1,875 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3566.dtsi"
+
+/ {
+ aliases {
+ mmc1 = &sdmmc0;
+ mmc2 = &sdmmc1;
+ mmc3 = &sdmmc2;
+ };
+
+ adc-joystick {
+ compatible = "adc-joystick";
+ io-channels = <&adc_mux 0>,
+ <&adc_mux 1>,
+ <&adc_mux 2>,
+ <&adc_mux 3>;
+ pinctrl-0 = <&joy_mux_en>;
+ pinctrl-names = "default";
+ poll-interval = <60>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ axis at 0 {
+ reg = <0>;
+ abs-flat = <32>;
+ abs-fuzz = <32>;
+ abs-range = <1023 15>;
+ linux,code = <ABS_X>;
+ };
+
+ axis at 1 {
+ reg = <1>;
+ abs-flat = <32>;
+ abs-fuzz = <32>;
+ abs-range = <15 1023>;
+ linux,code = <ABS_RX>;
+ };
+
+ axis at 2 {
+ reg = <2>;
+ abs-flat = <32>;
+ abs-fuzz = <32>;
+ abs-range = <15 1023>;
+ linux,code = <ABS_Y>;
+ };
+
+ axis at 3 {
+ reg = <3>;
+ abs-flat = <32>;
+ abs-fuzz = <32>;
+ abs-range = <1023 15>;
+ linux,code = <ABS_RY>;
+ };
+ };
+
+ adc_mux: adc-mux {
+ compatible = "io-channel-mux";
+ channels = "left_x", "right_x", "left_y", "right_y";
+ #io-channel-cells = <1>;
+ io-channels = <&saradc 3>;
+ io-channel-names = "parent";
+ mux-controls = <&gpio_mux>;
+ settle-time-us = <100>;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ power-supply = <&vcc_sys>;
+ pwms = <&pwm4 0 25000 0>;
+ };
+
+ battery: battery {
+ compatible = "simple-battery";
+ charge-full-design-microamp-hours = <3151000>;
+ charge-term-current-microamp = <300000>;
+ constant-charge-current-max-microamp = <2000000>;
+ constant-charge-voltage-max-microvolt = <4250000>;
+ factory-internal-resistance-micro-ohms = <117000>;
+ voltage-max-design-microvolt = <4172000>;
+ voltage-min-design-microvolt = <3400000>;
+
+ ocv-capacity-celsius = <20>;
+ ocv-capacity-table-0 = <4172000 100>, <4092000 95>, <4035000 90>, <3990000 85>,
+ <3939000 80>, <3895000 75>, <3852000 70>, <3807000 65>,
+ <3762000 60>, <3713000 55>, <3672000 50>, <3647000 45>,
+ <3629000 40>, <3613000 35>, <3598000 30>, <3578000 25>,
+ <3550000 20>, <3519000 15>, <3479000 10>, <3438000 5>,
+ <3400000 0>;
+ };
+
+ gpio_keys_control: gpio-keys-control {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&btn_pins_ctrl>;
+ pinctrl-names = "default";
+
+ button-a {
+ gpios = <&gpio3 RK_PC2 GPIO_ACTIVE_LOW>;
+ label = "EAST";
+ linux,code = <BTN_EAST>;
+ };
+
+ button-b {
+ gpios = <&gpio3 RK_PC3 GPIO_ACTIVE_LOW>;
+ label = "SOUTH";
+ linux,code = <BTN_SOUTH>;
+ };
+
+ button-down {
+ gpios = <&gpio3 RK_PA4 GPIO_ACTIVE_LOW>;
+ label = "DPAD-DOWN";
+ linux,code = <BTN_DPAD_DOWN>;
+ };
+
+ button-l1 {
+ gpios = <&gpio3 RK_PB1 GPIO_ACTIVE_LOW>;
+ label = "TL";
+ linux,code = <BTN_TL>;
+ };
+
+ button-l2 {
+ gpios = <&gpio3 RK_PB2 GPIO_ACTIVE_LOW>;
+ label = "TL2";
+ linux,code = <BTN_TL2>;
+ };
+
+ button-left {
+ gpios = <&gpio3 RK_PA6 GPIO_ACTIVE_LOW>;
+ label = "DPAD-LEFT";
+ linux,code = <BTN_DPAD_LEFT>;
+ };
+
+ button-r1 {
+ gpios = <&gpio3 RK_PB3 GPIO_ACTIVE_LOW>;
+ label = "TR";
+ linux,code = <BTN_TR>;
+ };
+
+ button-r2 {
+ gpios = <&gpio3 RK_PB4 GPIO_ACTIVE_LOW>;
+ label = "TR2";
+ linux,code = <BTN_TR2>;
+ };
+
+ button-right {
+ gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_LOW>;
+ label = "DPAD-RIGHT";
+ linux,code = <BTN_DPAD_RIGHT>;
+ };
+
+ button-select {
+ gpios = <&gpio3 RK_PB6 GPIO_ACTIVE_LOW>;
+ label = "SELECT";
+ linux,code = <BTN_SELECT>;
+ };
+
+ button-start {
+ gpios = <&gpio3 RK_PB5 GPIO_ACTIVE_LOW>;
+ label = "START";
+ linux,code = <BTN_START>;
+ };
+
+ button-thumbl {
+ gpios = <&gpio3 RK_PA1 GPIO_ACTIVE_LOW>;
+ label = "THUMBL";
+ linux,code = <BTN_THUMBL>;
+ };
+
+ button-thumbr {
+ gpios = <&gpio3 RK_PA2 GPIO_ACTIVE_LOW>;
+ label = "THUMBR";
+ linux,code = <BTN_THUMBR>;
+ };
+
+ button-up {
+ gpios = <&gpio3 RK_PA3 GPIO_ACTIVE_LOW>;
+ label = "DPAD-UP";
+ linux,code = <BTN_DPAD_UP>;
+ };
+
+ button-x {
+ gpios = <&gpio3 RK_PC0 GPIO_ACTIVE_LOW>;
+ label = "NORTH";
+ linux,code = <BTN_NORTH>;
+ };
+
+ button-y {
+ gpios = <&gpio3 RK_PC1 GPIO_ACTIVE_LOW>;
+ label = "WEST";
+ linux,code = <BTN_WEST>;
+ };
+ };
+
+ gpio_keys_vol: gpio-keys-vol {
+ compatible = "gpio-keys";
+ autorepeat;
+ pinctrl-0 = <&btn_pins_vol>;
+ pinctrl-names = "default";
+
+ button-vol-down {
+ gpios = <&gpio3 RK_PB0 GPIO_ACTIVE_LOW>;
+ label = "VOLUMEDOWN";
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+
+ button-vol-up {
+ gpios = <&gpio3 RK_PA7 GPIO_ACTIVE_LOW>;
+ label = "VOLUMEUP";
+ linux,code = <KEY_VOLUMEUP>;
+ };
+ };
+
+ gpio_mux: mux-controller {
+ compatible = "gpio-mux";
+ mux-gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_LOW>,
+ <&gpio0 RK_PB7 GPIO_ACTIVE_LOW>;
+ #mux-control-cells = <0>;
+ };
+
+ hdmi-con {
+ compatible = "hdmi-connector";
+ ddc-i2c-bus = <&i2c5>;
+ type = "c";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ /*
+ * Device also includes an always on LED that is wired to the 5V input
+ * voltage and is on when the device is plugged in.
+ */
+ leds: pwm-leds {
+ compatible = "pwm-leds";
+
+ green_led: led-0 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_STATUS;
+ max-brightness = <255>;
+ pwms = <&pwm6 0 25000 0>;
+ };
+
+ red_led: led-1 {
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_CHARGING;
+ max-brightness = <255>;
+ pwms = <&pwm7 0 25000 0>;
+ };
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rk817 1>;
+ clock-names = "ext_clock";
+ pinctrl-0 = <&wifi_enable_h>;
+ pinctrl-names = "default";
+ post-power-on-delay-ms = <200>;
+ reset-gpios = <&gpio4 RK_PA2 GPIO_ACTIVE_LOW>;
+ };
+
+ /*
+ * Channels reversed for speakers. Headphones automatically switch via hardware when
+ * detected with no ability to control output in software. Headphones appear to be mono
+ * (each output channel receives all audio). No microphone support on 3.5mm jack.
+ */
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "rk817_ext";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,mclk-fs = <256>;
+ simple-audio-card,widgets =
+ "Headphone", "Headphones";
+ simple-audio-card,routing =
+ "Headphones", "HPOL",
+ "Headphones", "HPOR";
+
+ simple-audio-card,codec {
+ sound-dai = <&rk817>;
+ };
+
+ simple-audio-card,cpu {
+ sound-dai = <&i2s1_8ch>;
+ };
+ };
+
+ vcc3v3_lcd0_n: regulator-vcc3v3-lcd0 {
+ compatible = "regulator-fixed";
+ gpio = <&gpio0 RK_PC2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ pinctrl-0 = <&vcc_lcd_h>;
+ pinctrl-names = "default";
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3_lcd0_n";
+ vin-supply = <&vcc_3v3>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_sys: regulator-vcc-sys {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3800000>;
+ regulator-max-microvolt = <3800000>;
+ regulator-name = "vcc_sys";
+ };
+
+ vcc_wifi: regulator-vcc-wifi {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 RK_PA0 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&vcc_wifi_h>;
+ pinctrl-names = "default";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc_wifi";
+ };
+};
+
+&combphy1 {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&dsi0 {
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ports {
+ dsi0_in: port at 0 {
+ reg = <0>;
+ dsi0_in_vp1: endpoint {
+ remote-endpoint = <&vp1_out_dsi0>;
+ };
+ };
+
+ dsi0_out: port at 1 {
+ reg = <1>;
+ mipi_out_panel: endpoint {
+ remote-endpoint = <&mipi_in_panel>;
+ };
+ };
+ };
+};
+
+&dsi_dphy0 {
+ status = "okay";
+};
+
+&gpu {
+ mali-supply = <&vdd_gpu>;
+ status = "okay";
+};
+
+&hdmi {
+ ddc-i2c-bus = <&i2c5>;
+ pinctrl-0 = <&hdmitxm0_cec>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&hdmi_in {
+ hdmi_in_vp0: endpoint {
+ remote-endpoint = <&vp0_out_hdmi>;
+ };
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&hdmi_sound {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ rk817: pmic at 20 {
+ compatible = "rockchip,rk817";
+ reg = <0x20>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+ clock-output-names = "rk808-clkout1", "rk808-clkout2";
+ clock-names = "mclk";
+ clocks = <&cru I2S1_MCLKOUT_TX>;
+ assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
+ assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
+ #clock-cells = <1>;
+ #sound-dai-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s1m0_mclk>, <&pmic_int_l>;
+ wakeup-source;
+
+ vcc1-supply = <&vcc_sys>;
+ vcc2-supply = <&vcc_sys>;
+ vcc3-supply = <&vcc_sys>;
+ vcc4-supply = <&vcc_sys>;
+ vcc5-supply = <&vcc_sys>;
+ vcc6-supply = <&vcc_sys>;
+ vcc7-supply = <&vcc_sys>;
+ vcc8-supply = <&vcc_sys>;
+ vcc9-supply = <&dcdc_boost>;
+
+ regulators {
+ vdd_logic: DCDC_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vdd_logic";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vdd_gpu: DCDC_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vdd_gpu";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vcc_ddr";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_3v3: DCDC_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vcc_3v3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcca1v8_pmu: LDO_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcca1v8_pmu";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdda_0v9: LDO_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vdda_0v9";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_pmu: LDO_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vdda0v9_pmu";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vccio_acodec: LDO_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio_acodec";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd: LDO_REG5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio_sd";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_pmu: LDO_REG6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3_pmu";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_1v8: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc_1v8";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc1v8_dvp: LDO_REG8 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc1v8_dvp";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc2v8_dvp: LDO_REG9 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "vcc2v8_dvp";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ dcdc_boost: BOOST {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <4700000>;
+ regulator-max-microvolt = <5400000>;
+ regulator-name = "boost";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ otg_switch: OTG_SWITCH {
+ regulator-name = "otg_switch";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+
+ rk817_charger: charger {
+ monitored-battery = <&battery>;
+ rockchip,resistor-sense-micro-ohms = <10000>;
+ rockchip,sleep-enter-current-microamp = <300000>;
+ rockchip,sleep-filter-current-microamp = <100000>;
+ };
+ };
+
+ vdd_cpu: regulator at 1c {
+ compatible = "tcs,tcs4525";
+ reg = <0x1c>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1390000>;
+ regulator-name = "vdd_cpu";
+ regulator-ramp-delay = <2300>;
+ vin-supply = <&vcc_sys>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+};
+
+&i2c5 {
+ pinctrl-0 = <&i2c5m1_xfer>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&i2s0_8ch {
+ status = "okay";
+};
+
+&i2s1_8ch {
+ pinctrl-0 = <&i2s1m0_sclktx
+ &i2s1m0_lrcktx
+ &i2s1m0_sdi0
+ &i2s1m0_sdo0>;
+ pinctrl-names = "default";
+ rockchip,trcm-sync-tx-only;
+ status = "okay";
+};
+
+&pinctrl {
+ gpio-btns {
+ btn_pins_ctrl: btn-pins-ctrl {
+ rockchip,pins =
+ <3 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PB1 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PB3 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PB4 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PB5 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PB6 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PC0 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PC1 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PC2 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PC3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ btn_pins_vol: btn-pins-vol {
+ rockchip,pins =
+ <3 RK_PA7 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ joy-mux {
+ joy_mux_en: joy-mux-en {
+ rockchip,pins =
+ <0 RK_PB5 RK_FUNC_GPIO &pcfg_output_low>;
+ };
+ };
+
+ gpio-lcd {
+ lcd_rst: lcd-rst {
+ rockchip,pins =
+ <4 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins =
+ <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ sdio-pwrseq {
+ wifi_enable_h: wifi-enable-h {
+ rockchip,pins =
+ <4 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ vcc3v3-lcd {
+ vcc_lcd_h: vcc-lcd-h {
+ rockchip,pins =
+ <0 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ vcc-wifi {
+ vcc_wifi_h: vcc-wifi-h {
+ rockchip,pins =
+ <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pmu_io_domains {
+ status = "okay";
+ pmuio1-supply = <&vcc3v3_pmu>;
+ pmuio2-supply = <&vcc3v3_pmu>;
+ vccio1-supply = <&vccio_acodec>;
+ vccio3-supply = <&vccio_sd>;
+ vccio4-supply = <&vcc_1v8>;
+ vccio5-supply = <&vcc_3v3>;
+ vccio6-supply = <&vcc1v8_dvp>;
+ vccio7-supply = <&vcc_3v3>;
+};
+
+&pwm4 {
+ status = "okay";
+};
+
+&pwm6 {
+ status = "okay";
+};
+
+&pwm7 {
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&sdmmc0 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+ pinctrl-names = "default";
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vccio_sd>;
+ status = "okay";
+};
+
+&sdmmc1 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cd-gpios = <&gpio2 RK_PB2 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk &sdmmc1_det>;
+ pinctrl-names = "default";
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vcc1v8_dvp>;
+ status = "okay";
+};
+
+&sdmmc2 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ non-removable;
+ pinctrl-0 = <&sdmmc2m0_bus4 &sdmmc2m0_cmd &sdmmc2m0_clk>;
+ pinctrl-names = "default";
+ vmmc-supply = <&vcc_wifi>;
+ vqmmc-supply = <&vcca1v8_pmu>;
+ status = "okay";
+};
+
+&tsadc {
+ rockchip,hw-tshut-mode = <1>;
+ rockchip,hw-tshut-polarity = <0>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-0 = <&uart1m1_xfer &uart1m1_ctsn &uart1m1_rtsn>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "realtek,rtl8821cs-bt", "realtek,rtl8723bs-bt";
+ device-wake-gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>;
+ enable-gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>;
+ host-wake-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&usb_host0_xhci {
+ dr_mode = "peripheral";
+ phys = <&usb2phy0_otg>;
+ phy-names = "usb2-phy";
+ status = "okay";
+};
+
+&usb_host1_ehci {
+ status = "okay";
+};
+
+&usb_host1_ohci {
+ status = "okay";
+};
+
+&usb_host1_xhci {
+ phy-names = "usb2-phy", "usb3-phy";
+ phys = <&usb2phy1_host>, <&combphy1 PHY_TYPE_USB3>;
+ status = "okay";
+};
+
+&usb2phy0 {
+ status = "okay";
+};
+
+&usb2phy0_otg {
+ status = "okay";
+};
+
+&usb2phy1 {
+ status = "okay";
+};
+
+&usb2phy1_host {
+ status = "okay";
+};
+
+&vop {
+ assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+ assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+ status = "okay";
+};
+
+&vop_mmu {
+ status = "okay";
+};
+
+&vp0 {
+ vp0_out_hdmi: endpoint at ROCKCHIP_VOP2_EP_HDMI0 {
+ reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+ remote-endpoint = <&hdmi_in_vp0>;
+ };
+};
+
+&vp1 {
+ vp1_out_dsi0: endpoint at ROCKCHIP_VOP2_EP_MIPI0 {
+ reg = <ROCKCHIP_VOP2_EP_MIPI0>;
+ remote-endpoint = <&dsi0_in_vp1>;
+ };
+};
--
2.34.1
More information about the Linux-rockchip
mailing list