[PATCHv5 07/10] mfd: rk8xx: add rk806 support
Lee Jones
lee at kernel.org
Fri Jan 20 08:59:21 PST 2023
On Mon, 09 Jan 2023, Sebastian Reichel wrote:
> Add support for SPI connected rk806, which is used by the RK3588
> evaluation boards. The PMIC is advertised to support I2C and SPI,
> but the evaluation boards all use SPI. Thus only SPI support is
> added here.
>
> Signed-off-by: Sebastian Reichel <sebastian.reichel at collabora.com>
> ---
> drivers/mfd/Kconfig | 14 ++
> drivers/mfd/Makefile | 1 +
> drivers/mfd/rk8xx-core.c | 67 ++++++-
> drivers/mfd/rk8xx-spi.c | 122 ++++++++++++
> include/linux/mfd/rk808.h | 409 ++++++++++++++++++++++++++++++++++++++
> 5 files changed, 611 insertions(+), 2 deletions(-)
> create mode 100644 drivers/mfd/rk8xx-spi.c
>
> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> index 692e38283bda..13582ea5cb44 100644
> --- a/drivers/mfd/Kconfig
> +++ b/drivers/mfd/Kconfig
> @@ -1222,6 +1222,20 @@ config MFD_RK8XX_I2C
> through I2C interface. The device supports multiple sub-devices
> including interrupts, RTC, LDO & DCDC regulators, and onkey.
>
> +config MFD_RK8XX_SPI
> + tristate "Rockchip RK806 Power Management Chip"
> + depends on SPI && OF
> + select MFD_CORE
> + select REGMAP_SPI
> + select REGMAP_IRQ
> + select MFD_RK8XX
> + help
> + If you say yes here you get support for the RK806 Power Management
> + chip.
> + This driver provides common support for accessing the device
> + through an SPI interface. The device supports multiple sub-devices
> + including interrupts, LDO & DCDC regulators, and power on-key.
> +
> config MFD_RN5T618
> tristate "Ricoh RN5T567/618 PMIC"
> depends on I2C
> diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
> index f65ef1bd0810..a88f27cd837b 100644
> --- a/drivers/mfd/Makefile
> +++ b/drivers/mfd/Makefile
> @@ -222,6 +222,7 @@ obj-$(CONFIG_MFD_NTXEC) += ntxec.o
> obj-$(CONFIG_MFD_RC5T583) += rc5t583.o rc5t583-irq.o
> obj-$(CONFIG_MFD_RK8XX) += rk8xx-core.o
> obj-$(CONFIG_MFD_RK8XX_I2C) += rk8xx-i2c.o
> +obj-$(CONFIG_MFD_RK8XX_SPI) += rk8xx-spi.o
> obj-$(CONFIG_MFD_RN5T618) += rn5t618.o
> obj-$(CONFIG_MFD_SEC_CORE) += sec-core.o sec-irq.o
> obj-$(CONFIG_MFD_SYSCON) += syscon.o
> diff --git a/drivers/mfd/rk8xx-core.c b/drivers/mfd/rk8xx-core.c
> index c52f5fa1a4da..289f4c1f30c2 100644
> --- a/drivers/mfd/rk8xx-core.c
> +++ b/drivers/mfd/rk8xx-core.c
> @@ -37,6 +37,11 @@ static const struct resource rk805_key_resources[] = {
> DEFINE_RES_IRQ(RK805_IRQ_PWRON_FALL),
> };
>
> +static struct resource rk806_pwrkey_resources[] = {
> + DEFINE_RES_IRQ(RK806_IRQ_PWRON_FALL),
> + DEFINE_RES_IRQ(RK806_IRQ_PWRON_RISE),
> +};
> +
> static const struct resource rk817_pwrkey_resources[] = {
> DEFINE_RES_IRQ(RK817_IRQ_PWRON_RISE),
> DEFINE_RES_IRQ(RK817_IRQ_PWRON_FALL),
> @@ -64,6 +69,16 @@ static const struct mfd_cell rk805s[] = {
> },
> };
>
> +static const struct mfd_cell rk806s[] = {
> + { .name = "rk805-pinctrl", },
> + { .name = "rk808-regulator", },
> + {
> + .name = "rk805-pwrkey",
> + .num_resources = ARRAY_SIZE(rk806_pwrkey_resources),
> + .resources = &rk806_pwrkey_resources[0],
My OCD-sense is tingling.
Could you please add the resources *before* the num_resources please?
Also: '.resources = rk806_pwrkey_resources' is fine
> + },
> +};
> +
> static const struct mfd_cell rk808s[] = {
> { .name = "rk808-clkout", .id = PLATFORM_DEVID_NONE, },
> { .name = "rk808-regulator", .id = PLATFORM_DEVID_NONE, },
> @@ -122,6 +137,12 @@ static const struct rk808_reg_data rk805_pre_init_reg[] = {
> {RK805_THERMAL_REG, TEMP_HOTDIE_MSK, TEMP115C},
> };
>
> +static const struct rk808_reg_data rk806_pre_init_reg[] = {
> + { RK806_GPIO_INT_CONFIG, RK806_INT_POL_MSK, RK806_INT_POL_L },
> + { RK806_SYS_CFG3, RK806_SLAVE_RESTART_FUN_MSK, RK806_SLAVE_RESTART_FUN_EN },
> + { RK806_SYS_OPTION, RK806_SYS_ENB2_2M_MSK, RK806_SYS_ENB2_2M_EN },
> +};
> +
> static const struct rk808_reg_data rk808_pre_init_reg[] = {
> { RK808_BUCK3_CONFIG_REG, BUCK_ILMIN_MASK, BUCK_ILMIN_150MA },
> { RK808_BUCK4_CONFIG_REG, BUCK_ILMIN_MASK, BUCK_ILMIN_200MA },
> @@ -272,6 +293,27 @@ static const struct regmap_irq rk805_irqs[] = {
> },
> };
>
> +static const struct regmap_irq rk806_irqs[] = {
> + /* INT_STS0 IRQs */
> + REGMAP_IRQ_REG(RK806_IRQ_PWRON_FALL, 0, RK806_INT_STS_PWRON_FALL),
> + REGMAP_IRQ_REG(RK806_IRQ_PWRON_RISE, 0, RK806_INT_STS_PWRON_RISE),
> + REGMAP_IRQ_REG(RK806_IRQ_PWRON, 0, RK806_INT_STS_PWRON),
> + REGMAP_IRQ_REG(RK806_IRQ_PWRON_LP, 0, RK806_INT_STS_PWRON_LP),
> + REGMAP_IRQ_REG(RK806_IRQ_HOTDIE, 0, RK806_INT_STS_HOTDIE),
> + REGMAP_IRQ_REG(RK806_IRQ_VDC_RISE, 0, RK806_INT_STS_VDC_RISE),
> + REGMAP_IRQ_REG(RK806_IRQ_VDC_FALL, 0, RK806_INT_STS_VDC_FALL),
> + REGMAP_IRQ_REG(RK806_IRQ_VB_LO, 0, RK806_INT_STS_VB_LO),
> + /* INT_STS1 IRQs */
> + REGMAP_IRQ_REG(RK806_IRQ_REV0, 1, RK806_INT_STS_REV0),
> + REGMAP_IRQ_REG(RK806_IRQ_REV1, 1, RK806_INT_STS_REV1),
> + REGMAP_IRQ_REG(RK806_IRQ_REV2, 1, RK806_INT_STS_REV2),
> + REGMAP_IRQ_REG(RK806_IRQ_CRC_ERROR, 1, RK806_INT_STS_CRC_ERROR),
> + REGMAP_IRQ_REG(RK806_IRQ_SLP3_GPIO, 1, RK806_INT_STS_SLP3_GPIO),
> + REGMAP_IRQ_REG(RK806_IRQ_SLP2_GPIO, 1, RK806_INT_STS_SLP2_GPIO),
> + REGMAP_IRQ_REG(RK806_IRQ_SLP1_GPIO, 1, RK806_INT_STS_SLP1_GPIO),
> + REGMAP_IRQ_REG(RK806_IRQ_WDT, 1, RK806_INT_STS_WDT),
> +};
> +
> static const struct regmap_irq rk808_irqs[] = {
> /* INT_STS */
> [RK808_IRQ_VOUT_LO] = {
> @@ -422,6 +464,18 @@ static struct regmap_irq_chip rk805_irq_chip = {
> .init_ack_masked = true,
> };
>
> +static struct regmap_irq_chip rk806_irq_chip = {
> + .name = "rk806",
> + .irqs = rk806_irqs,
> + .num_irqs = ARRAY_SIZE(rk806_irqs),
> + .num_regs = 2,
> + .irq_reg_stride = 2,
> + .mask_base = RK806_INT_MSK0,
> + .status_base = RK806_INT_STS0,
> + .ack_base = RK806_INT_STS0,
> + .init_ack_masked = true,
> +};
> +
> static const struct regmap_irq_chip rk808_irq_chip = {
> .name = "rk808",
> .irqs = rk808_irqs,
> @@ -548,6 +602,7 @@ int rk8xx_probe(struct device *dev, int variant, unsigned int irq, struct regmap
> struct rk808 *rk808;
> const struct rk808_reg_data *pre_init_reg;
> const struct mfd_cell *cells;
> + bool dual_support = false;
> int nr_pre_init_regs;
> int nr_cells;
> int ret;
> @@ -569,6 +624,14 @@ int rk8xx_probe(struct device *dev, int variant, unsigned int irq, struct regmap
> cells = rk805s;
> nr_cells = ARRAY_SIZE(rk805s);
> break;
> + case RK806_ID:
> + rk808->regmap_irq_chip = &rk806_irq_chip;
> + pre_init_reg = rk806_pre_init_reg;
> + nr_pre_init_regs = ARRAY_SIZE(rk806_pre_init_reg);
> + cells = rk806s;
> + nr_cells = ARRAY_SIZE(rk806s);
> + dual_support = true;
> + break;
> case RK808_ID:
> rk808->regmap_irq_chip = &rk808_irq_chip;
> pre_init_reg = rk808_pre_init_reg;
> @@ -602,7 +665,7 @@ int rk8xx_probe(struct device *dev, int variant, unsigned int irq, struct regmap
> return dev_err_probe(dev, -EINVAL, "No interrupt support, no core IRQ\n");
>
> ret = devm_regmap_add_irq_chip(dev, rk808->regmap, irq,
> - IRQF_ONESHOT, -1,
> + IRQF_ONESHOT | (dual_support ? IRQF_SHARED : 0), -1,
Why not 'dual_support = IRQF_SHARED', then | it regardless?
> rk808->regmap_irq_chip, &rk808->irq_data);
> if (ret)
> return dev_err_probe(dev, ret, "Failed to add irq_chip\n");
> @@ -617,7 +680,7 @@ int rk8xx_probe(struct device *dev, int variant, unsigned int irq, struct regmap
> pre_init_reg[i].addr);
> }
>
> - ret = devm_mfd_add_devices(dev, PLATFORM_DEVID_NONE,
> + ret = devm_mfd_add_devices(dev, dual_support ? PLATFORM_DEVID_AUTO : PLATFORM_DEVID_NONE,
Any reason why you can't use AUTO all the time?
> cells, nr_cells, NULL, 0,
> regmap_irq_get_domain(rk808->irq_data));
> if (ret)
> diff --git a/drivers/mfd/rk8xx-spi.c b/drivers/mfd/rk8xx-spi.c
> new file mode 100644
> index 000000000000..3fbcaaaa453a
> --- /dev/null
> +++ b/drivers/mfd/rk8xx-spi.c
> @@ -0,0 +1,122 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Rockchip RK806 Core (SPI) driver
> + *
> + * Copyright (c) 2021 Rockchip Electronics Co., Ltd.
> + * Copyright (c) 2023 Collabora Ltd.
> + *
> + * Author: Xu Shengfei <xsf at rock-chips.com>
> + * Author: Sebastian Reichel <sebastian.reichel at collabora.com>
> + */
> +
> +#include <linux/interrupt.h>
> +#include <linux/mfd/core.h>
> +#include <linux/mfd/rk808.h>
> +#include <linux/module.h>
> +#include <linux/regmap.h>
> +#include <linux/spi/spi.h>
> +
> +#define RK806_CMD 0
> +#define RK806_REG_ADDR_L 1
> +#define RK806_REG_ADDR_H 2
> +
> +static const struct regmap_range rk806_volatile_ranges[] = {
> + regmap_reg_range(RK806_POWER_EN0, RK806_POWER_EN5),
> + regmap_reg_range(RK806_DVS_START_CTRL, RK806_INT_MSK1),
> +};
> +
> +static const struct regmap_access_table rk806_volatile_table = {
> + .yes_ranges = rk806_volatile_ranges,
> + .n_yes_ranges = ARRAY_SIZE(rk806_volatile_ranges),
> +};
> +
> +static const struct regmap_config rk806_regmap_config_spi = {
> + .reg_bits = 8,
> + .val_bits = 8,
> + .cache_type = REGCACHE_RBTREE,
> + .volatile_table = &rk806_volatile_table,
> +};
> +
> +static int rk806_spi_bus_write(void *context, const void *vdata, size_t count)
> +{
> + struct device *dev = context;
> + struct spi_device *spi = to_spi_device(dev);
> + const char *data = vdata;
> + char buffer[3] = { 0 };
> + struct spi_transfer xfer[2] = { 0 };
> +
> + buffer[RK806_CMD] = RK806_CMD_WRITE | (count - 2);
Comment or define please.
> + buffer[RK806_REG_ADDR_L] = data[0];
As above.
> + buffer[RK806_REG_ADDR_H] = RK806_REG_H;
> +
> + xfer[0].tx_buf = buffer;
> + xfer[0].len = sizeof(buffer);
> + xfer[1].tx_buf = data+1;
And here.
> + xfer[1].len = count-1;
Here too.
Nit: spaces around the '+' and '-' please.
> + return spi_sync_transfer(spi, xfer, ARRAY_SIZE(xfer));
> +}
> +
> +static int rk806_spi_bus_read(void *context, const void *vreg, size_t reg_size,
> + void *val, size_t val_size)
> +{
> + struct device *dev = context;
> + struct spi_device *spi = to_spi_device(dev);
> + const char *reg = vreg;
> + char txbuf[3] = { 0 };
> +
> + if (reg_size != sizeof(char) || val_size < 1)
> + return -EINVAL;
> +
> + txbuf[RK806_CMD] = RK806_CMD_READ | (val_size - 1);
> + txbuf[RK806_REG_ADDR_L] = *reg;
> + txbuf[RK806_REG_ADDR_H] = RK806_REG_H;
What's this for? Isn't it already 0?
> + return spi_write_then_read(spi, txbuf, sizeof(txbuf), val, val_size);
> +}
> +
> +static const struct regmap_bus rk806_regmap_bus_spi = {
> + .write = rk806_spi_bus_write,
> + .read = rk806_spi_bus_read,
> + .reg_format_endian_default = REGMAP_ENDIAN_NATIVE,
> + .val_format_endian_default = REGMAP_ENDIAN_NATIVE,
> +};
> +
> +static int rk8xx_spi_probe(struct spi_device *spi)
> +{
> + struct regmap *regmap;
> +
> + regmap = devm_regmap_init(&spi->dev, &rk806_regmap_bus_spi,
> + &spi->dev, &rk806_regmap_config_spi);
> + if (IS_ERR(regmap))
> + return dev_err_probe(&spi->dev, PTR_ERR(regmap),
> + "Failed to initialize register map\n");
> +
> + return rk8xx_probe(&spi->dev, RK806_ID, spi->irq, regmap);
> +}
> +
> +static const struct of_device_id rk8xx_spi_of_match[] = {
> + { .compatible = "rockchip,rk806", },
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, rk8xx_spi_of_match);
> +
> +static const struct spi_device_id rk8xx_spi_id_table[] = {
> + { "rk806", 0 },
> + { }
> +};
> +MODULE_DEVICE_TABLE(spi, rk8xx_spi_id_table);
> +
> +static struct spi_driver rk8xx_spi_driver = {
> + .driver = {
> + .name = "rk8xx-spi",
> + .of_match_table = rk8xx_spi_of_match,
> + },
> + .probe = rk8xx_spi_probe,
> + .id_table = rk8xx_spi_id_table,
> +};
> +module_spi_driver(rk8xx_spi_driver);
> +
> +MODULE_AUTHOR("Xu Shengfei <xsf at rock-chips.com>");
> +MODULE_DESCRIPTION("RK8xx SPI PMIC driver");
> +MODULE_LICENSE("GPL v2");
> diff --git a/include/linux/mfd/rk808.h b/include/linux/mfd/rk808.h
--
Lee Jones [李琼斯]
More information about the Linux-rockchip
mailing list