[PATCH 2/2] arm64: dts: rockchip: Add initial support for Pine64 PinePhone Pro
Ondřej Jirman
megous at megous.com
Sun May 29 04:33:09 PDT 2022
Hi Tom,
On Sun, May 29, 2022 at 01:17:05PM +1000, Tom Fitzhenry wrote:
> This is a basic DT that includes only features that are already
> supported by mainline drivers.
>
> Tested to work: booting from eMMC, WiFi, charging.
>
> Future patches will flesh out the DT. Some components, e.g. the panel,
> are awaiting driver mainlining.
>
> This is derived from a combination of https://gitlab.com/pine64-org/linux
> and https://megous.com/git/linux.
this patch has a bunch of issues that were already fixed during discussions
with Martijn as part of his effort to prepare an initial device tree for
PinephonePro. (also noted below for your reference)
I suggest to wait for the original author's submission.
kind regards,
o.
> https://wiki.pine64.org/wiki/PinePhone_Pro
>
> Co-developed-by: Ondrej Jirman <megous at megous.com>
> Co-developed-by: Martijn Braam <martijn at brixit.nl>
> Signed-off-by: Tom Fitzhenry <tom at tom-fitzhenry.me.uk>
> ---
> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> .../dts/rockchip/rk3399-pinephone-pro.dts | 939 ++++++++++++++++++
> 2 files changed, 940 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
>
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index 4ae9f35434b8..c00e7922d974 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -41,6 +41,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-neo4.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-r4s.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-orangepi.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-pinebook-pro.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-pinephone-pro.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-puma-haikou.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc-mezzanine.dtb
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts b/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
> new file mode 100644
> index 000000000000..b1a486db1dfe
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
> @@ -0,0 +1,939 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2020 Martijn Braam <martijn at brixit.nl>
> + * Copyright (c) 2021 Kamil Trzciński <ayufan at ayufan.eu>
> + */
> +
> +// PinePhone Pro datasheet: https://files.pine64.org/doc/PinePhonePro/PinephonePro-Schematic-V1.0-20211127.pdf
> +
> +/dts-v1/;
> +#include <dt-bindings/input/gpio-keys.h>
> +#include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/usb/pd.h>
> +#include <dt-bindings/leds/common.h>
> +#include "rk3399.dtsi"
> +#include "rk3399-opp.dtsi"
> +
> +/ {
> + model = "Pine64 PinePhonePro";
> + compatible = "pine64,pinephone-pro", "rockchip,rk3399";
> +
> + chosen {
> + bootargs = "earlycon=uart8250,mmio32,0xff1a0000";
> + stdout-path = "serial2:115200n8";
> + };
> +
> + // Per "RK 3399 SARADC", page 8.
> + adc-keys {
> + compatible = "adc-keys";
> + io-channels = <&saradc 1>;
> + io-channel-names = "buttons";
> + keyup-threshold-microvolt = <1600000>;
> + poll-interval = <100>;
> +
> + button-up {
> + label = "Volume Up";
> + linux,code = <KEY_VOLUMEUP>;
> + press-threshold-microvolt = <100000>;
> + };
> +
> + button-down {
> + label = "Volume Down";
> + linux,code = <KEY_VOLUMEDOWN>;
> + press-threshold-microvolt = <300000>;
> + };
> + };
> +
> + cluster1_opp_ppp: opp-table1b {
> + compatible = "operating-points-v2";
> + opp-shared;
> +
> + opp00 {
> + opp-hz = /bits/ 64 <408000000>;
> + opp-microvolt = <800000>;
> + clock-latency-ns = <40000>;
> + };
> + opp01 {
> + opp-hz = /bits/ 64 <600000000>;
> + opp-microvolt = <800000>;
> + };
> + opp02 {
> + opp-hz = /bits/ 64 <816000000>;
> + opp-microvolt = <825000>;
> + };
> + opp03 {
> + opp-hz = /bits/ 64 <1008000000>;
> + opp-microvolt = <875000>;
> + };
> + opp04 {
> + opp-hz = /bits/ 64 <1200000000>;
> + opp-microvolt = <950000>;
> + };
> + opp05 {
> + opp-hz = /bits/ 64 <1416000000>;
> + opp-microvolt = <1025000>;
> + };
> + };
> +
> + // Per "BACKLIGHT", page 16.
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm0 0 1000000 0>;
> + pwm-delay-us = <10000>;
> + };
> +
> + // Per "RK3399 GPIO", page 11.
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&red_led_pin &green_led_pin &blue_led_pin>;
> +
> + led-standby {
> + color = <LED_COLOR_ID_RED>;
> + default-state = "off";
> + function = LED_FUNCTION_STANDBY;
> + gpios = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>;
> + label = "red:standby";
> + panic-indicator;
> + retain-state-suspended;
> + };
> +
> + led-pwr {
> + color = <LED_COLOR_ID_GREEN>;
> + default-state = "on";
> + function = LED_FUNCTION_POWER;
> + gpios = <&gpio4 RK_PD5 GPIO_ACTIVE_HIGH>;
> + label = "green:disk-activity";
> + };
> +
> + blue-charging {
> + color = <LED_COLOR_ID_BLUE>;
> + default-state = "off";
> + function = LED_FUNCTION_CHARGING;
> + gpios = <&gpio4 RK_PD6 GPIO_ACTIVE_HIGH>;
> + label = "blue:charging";
> + };
> + };
^^ these are general indicator LEDs, they don't have a function marked on the
chasis of the phone.
> + gpio-key-power {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pwrbtn_pin>;
> +
> + power {
> + debounce-interval = <20>;
> + // Per "PMU Controler", page 4.
> + gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
> + label = "Power";
> + linux,code = <KEY_POWER>;
> + wakeup-source;
> + };
> + };
> +
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + clocks = <&rk818 1>;
> + clock-names = "ext_clock";
> + pinctrl-names = "default";
> + pinctrl-0 = <&wifi_enable_h>;
> + post-power-on-delay-ms = <100>;
> + power-off-delay-us = <500000>;
> +
> + /* WL_REG_ON on module */
> + reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
> + };
> +
> + vibrator {
> + compatible = "gpio-vibrator";
> + // Per "GPIO", page 11.
> + enable-gpios = <&gpio3 RK_PB1 GPIO_ACTIVE_HIGH>;
> + // Per "Motor", page 17.
> + vcc-supply = <&vcc3v3_sys>;
> + };
> +
> + /* Power tree */
> + /* Root power source */
> + vcc_sysin: vcc-sysin {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_sysin";
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vcc5v0_sys: vcc5v0-host-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc5v0_sys";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_sysin>;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc5v0_typec: vcc5v0-typec-regulator {
> + compatible = "regulator-fixed";
> + gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&vcc5v0_typec_en>;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-name = "vcc5v0_typec";
> + vin-supply = <&vcc5v0_sys>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
^^^ this is not a regulator and doesn't switch on VBUS supply
for type-c port. That's done by the otg_switch
> + /* Main 3.3v supply */
> + vcc3v3_sys: wifi_bat: vcc3v3-sys {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc3v3_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vcc_sysin>;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc1v8_codec: vcc1v8-codec-regulator {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio3 RK_PA4 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&vcc1v8_codec_en>;
> + regulator-name = "vcc1v8_codec";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vcc3v3_sys>;
> + };
> +
> + /* MIPI DSI panel 1.8v supply */
> + vcc1v8_lcd: vcc1v8-lcd {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + regulator-name = "vcc1v8_lcd";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vcc3v3_sys>;
> + gpio = <&gpio3 RK_PA5 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&display_pwren1>;
> + };
> +
> + /* MIPI DSI panel 2.8v supply */
> + vcc2v8_lcd: vcc2v8-lcd {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + regulator-name = "vcc2v8_lcd";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + vin-supply = <&vcc3v3_sys>;
> + gpio = <&gpio3 RK_PA1 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&display_pwren>;
> + };
> +
> + vcca1v8_s3: vcc1v8-s3 {
> + compatible = "regulator-fixed";
> + regulator-name = "vcca1v8_s3";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vcc3v3_sys>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +};
> +
> +&cpu_l0 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l1 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l2 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l3 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_b0 {
> + cpu-supply = <&vdd_cpu_b>;
> + operating-points-v2 = <&cluster1_opp_ppp>;
> +};
> +
> +&cpu_b1 {
> + cpu-supply = <&vdd_cpu_b>;
> + operating-points-v2 = <&cluster1_opp_ppp>;
> +};
> +
> +&emmc_phy {
> + status = "okay";
> +};
> +
> +&gpu {
> + mali-supply = <&vdd_gpu>;
> + status = "okay";
> +};
> +
> +&i2c0 {
> + // Per "SCL clock frequency", page 30, RK818 datasheet.
> + clock-frequency = <400000>;
> + i2c-scl-rising-time-ns = <168>;
> + i2c-scl-falling-time-ns = <4>;
> + status = "okay";
> +
> + // Per "PMIC RK818-3", page 13.
> + rk818: pmic at 1c {
> + compatible = "rockchip,rk818";
> + reg = <0x1c>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <RK_PC5 IRQ_TYPE_LEVEL_LOW>;
> + #clock-cells = <1>;
> + clock-output-names = "xin32k", "rk808-clkout2";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_int_l>;
> + rockchip,system-power-controller;
> + wakeup-source;
> + extcon = <&fusb0>;
rk818 doesn't use extcon interface
> + vcc1-supply = <&vcc_sysin>;
> + vcc2-supply = <&vcc_sysin>;
> + vcc3-supply = <&vcc_sysin>;
> + vcc4-supply = <&vcc_sysin>;
> + vcc6-supply = <&vcc_sysin>;
> + vcc7-supply = <&vcc3v3_sys>;
> + vcc8-supply = <&vcc_sysin>;
> + vcc9-supply = <&vcc3v3_sys>;
> +
> + regulators {
> + vdd_cpu_l: DCDC_REG1 {
> + regulator-name = "vdd_cpu_l";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <6001>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_center: DCDC_REG2 {
> + regulator-name = "vdd_center";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <6001>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + // DDR
> + vcc_ddr: DCDC_REG3 {
> + regulator-name = "vcc_ddr";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-state-mem {
> + // Power RAM while suspended.
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc_1v8: vcc_wl: DCDC_REG4 {
> + regulator-name = "vcc_1v8";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + // Audio codec.
> + vcca3v0_codec: LDO_REG1 {
> + regulator-name = "vcca3v0_codec";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + // Touch screen.
> + vcc3v0_touch: LDO_REG2 {
> + regulator-name = "vcc3v0_touch";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcca1v8_codec: LDO_REG3 {
> + regulator-name = "vcca1v8_codec";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_power_on: LDO_REG4 {
> + regulator-name = "vcc_power_on";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vcc_3v0: LDO_REG5 {
> + regulator-name = "vcc_3v0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3000000>;
> + };
> + };
> +
> + vcc_1v5: LDO_REG6 {
> + regulator-name = "vcc_1v5";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1500000>;
> + regulator-max-microvolt = <1500000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1500000>;
> + };
> + };
> +
> + vcc1v8_dvp: LDO_REG7 {
> + regulator-name = "vcc1v8_dvp";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc3v3_s3: LDO_REG8 {
> + regulator-name = "vcc3v3_s3";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vccio_sd: LDO_REG9 {
> + regulator-name = "vccio_sd";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vcc3v3_s0: SWITCH_REG {
> + regulator-name = "vcc3v3_s0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + boost_otg: DCDC_BOOST {
> + regulator-name = "boost_otg";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <5000000>;
> + };
> + };
> +
> + otg_switch: OTG_SWITCH {
> + regulator-name = "otg_switch";
> + };
> + };
> + };
> +
> + vdd_cpu_b: regulator at 40 {
> + compatible = "silergy,syr827";
> + reg = <0x40>;
> + fcs,suspend-voltage-selector = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&vsel1_pin>;
> + regulator-name = "vdd_cpu_b";
> + regulator-min-microvolt = <712500>;
> + regulator-max-microvolt = <1500000>;
> + regulator-ramp-delay = <1000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_gpu: regulator at 41 {
> + compatible = "silergy,syr828";
> + reg = <0x41>;
> + fcs,suspend-voltage-selector = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&vsel2_pin>;
> + regulator-name = "vdd_gpu";
> + regulator-min-microvolt = <712500>;
> + regulator-max-microvolt = <1500000>;
> + regulator-ramp-delay = <1000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +};
> +
> +&i2c1 {
> + i2c-scl-rising-time-ns = <300>;
> + i2c-scl-falling-time-ns = <15>;
> + status = "okay";
> +};
> +
> +&i2c3 {
> + i2c-scl-rising-time-ns = <450>;
> + i2c-scl-falling-time-ns = <15>;
> + status = "okay";
> +
> + // Per "Ambient Light", page 17.
> + light-sensor at 48 {
> + compatible = "sensortek,stk3311";
> + reg = <0x48>;
> + interrupt-parent = <&gpio4>;
> + interrupts = <RK_PD3 IRQ_TYPE_EDGE_FALLING>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&stk3311_int>;
> + vdd-supply = <&vcc_3v0>;
> + leda-supply = <&vcc_3v0>;
> + };
> +};
> +
> +&i2c4 {
> + i2c-scl-rising-time-ns = <600>;
> + i2c-scl-falling-time-ns = <20>;
> + status = "okay";
> +
> + // Per "TYPE-C", page 23.
> + fusb0: typec-portc at 22 {
> + compatible = "fcs,fusb302";
> + reg = <0x22>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <RK_PA2 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&fusb0_int>;
> + vbus-supply = <&vcc5v0_typec>;
> +
> + connector {
> + compatible = "usb-c-connector";
> + data-role = "dual";
> + label = "USB-C";
> + op-sink-microwatt = <1000000>;
> + power-role = "dual";
> + sink-pdos =
> + <PDO_FIXED(5000, 2500, PDO_FIXED_USB_COMM)>;
> + source-pdos =
> + <PDO_FIXED(5000, 1400, PDO_FIXED_USB_COMM)>;
> + try-power-role = "sink";
> +
> + extcon-cables = <1 2 5 6 9 10 12 44>;
> + typec-altmodes = <0xff01 1 0x001c0c00 1>;
^^^ these are not mainline bindings
Mainline uses mode-switch / orientation-switch / usb-role-switch properties and
altmodes node. Specified VDO (0x001c0c00) is also incorrect. And I don't think
the phone can provide 1.4A at 5V (that would be 7W)
VCC5V0_SYS can provide at most 2A and it's shared between modem, power amp for
the speaker, and type-c VCONN which also has some power requirements (1W).
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port at 0 {
> + reg = <0>;
> +
> + usbc_hs: endpoint {
> + remote-endpoint =
> + <&u2phy0_typec_hs>;
> + };
> + };
> +
> + port at 1 {
> + reg = <1>;
> +
> + usbc_ss: endpoint {
> + remote-endpoint =
> + <&tcphy0_typec_ss>;
> + };
> + };
> +
> + port at 2 {
> + reg = <2>;
> +
> + usbc_dp: endpoint {
> + remote-endpoint =
> + <&tcphy0_typec_dp>;
> + };
> + };
> + };
> + };
> + };
> +
> + // Per "Gyro", page 17.
> + accelerometer at 68 {
> + compatible = "invensense,mpu6500";
> + reg = <0x68>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <RK_PC6 IRQ_TYPE_LEVEL_LOW>;
> + vdd-supply = <&vcc_1v8>;
> + vddio-supply = <&vcc_1v8>;
> +
> + mount-matrix =
> + "1", "0", "0",
> + "0", "-1", "0",
> + "0", "0", "1";
> + };
> +};
> +
> +&io_domains {
> + status = "okay";
> +
> + bt656-supply = <&vcc1v8_dvp>;
> + audio-supply = <&vcca1v8_codec>;
> + sdmmc-supply = <&vccio_sd>;
> + gpio1830-supply = <&vcc_3v0>;
> +};
> +
> +&pmu_io_domains {
> + pmu1830-supply = <&vcc_1v8>;
> + status = "okay";
> +};
> +
> +&pinctrl {
> + bt {
> + bt_enable_h: bt-enable-h {
> + rockchip,pins = <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + bt_host_wake_l: bt-host-wake-l {
> + rockchip,pins = <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> +
> + bt_wake_l: bt-wake-l {
> + rockchip,pins = <2 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + buttons {
> + pwrbtn_pin: pwrbtn-pin {
> + rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +
> + fusb302x {
> + fusb0_int: fusb0-int {
> + rockchip,pins = <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +
> + leds {
> + red_led_pin: red-led-pin {
> + rockchip,pins = <4 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + green_led_pin: green-led-pin {
> + rockchip,pins = <4 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + blue_led_pin: blue-led-pin {
> + rockchip,pins = <4 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + pmic {
> + pmic_int_l: pmic-int-l {
> + rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> +
> + vsel1_pin: vsel1-pin {
> + rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> +
> + vsel2_pin: vsel2-pin {
> + rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> + };
> +
> + sdcard {
> + sdmmc0_pwr_h: sdmmc0-pwr-h {
> + rockchip,pins = <0 RK_PA1 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + };
> +
> + sdio-pwrseq {
> + wifi_enable_h: wifi-enable-h {
> + rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + usb-typec {
> + vcc5v0_typec_en: vcc5v0_typec_en {
> + rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +
> + dsi {
> + display_rst_l: display-rst-l {
> + rockchip,pins = <4 RK_PD1 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> +
> + display_pwren: display-pwren {
> + rockchip,pins = <3 RK_PA1 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> +
> + display_pwren1: display-pwren1 {
> + rockchip,pins = <3 RK_PA5 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> + };
> +
> + stk3311 {
> + stk3311_int: stk3311-int {
> + rockchip,pins = <4 RK_PD3 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +
> + sound {
> + vcc1v8_codec_en: vcc1v8-codec-en {
> + rockchip,pins = <3 RK_PA4 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> + };
> +};
> +
> +&pwm0 {
> + status = "okay";
> +};
> +
> +&pwm1 {
> + status = "okay";
> +};
> +
> +&pwm2 {
> + status = "okay";
> +};
> +
> +// Per "SARADC", page 8.
> +&saradc {
> + vref-supply = <&vcca1v8_s3>;
> + status = "okay";
> +};
> +
> +&sdio0 {
> + bus-width = <4>;
> + cap-sd-highspeed;
> + cap-sdio-irq;
> + disable-wp;
> + keep-power-in-suspend;
> + mmc-pwrseq = <&sdio_pwrseq>;
> + non-removable;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdio0_bus4 &sdio0_cmd &sdio0_clk>;
> + sd-uhs-sdr104;
> + status = "okay";
> +};
> +
> +// Per "SDMMC Controler", page 6.
> +&sdmmc {
> + bus-width = <4>;
> + cap-sd-highspeed;
> + cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
> + disable-wp;
> + max-frequency = <150000000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
> + vmmc-supply = <&vcc3v3_sys>;
> + vqmmc-supply = <&vccio_sd>;
> + status = "okay";
> +};
> +
> +&sdhci {
> + bus-width = <8>;
> + mmc-hs200-1_8v;
> + non-removable;
> + status = "okay";
> +};
> +
> +&tcphy0 {
> + extcon = <&fusb0>;
> + status = "okay";
> +};
^^^ this does not work. fusb0 doesn't provide any extcon interface
it only consumes one, just like tcphy0
> +&tcphy0_dp {
> + port {
> + tcphy0_typec_dp: endpoint {
> + remote-endpoint = <&usbc_dp>;
> + };
> + };
> +};
> +
> +&tcphy0_usb3 {
> + port {
> + tcphy0_typec_ss: endpoint {
> + remote-endpoint = <&usbc_ss>;
> + };
> + };
> +};
> +
> +// Enable thermal sensors.
> +&tsadc {
> + /* tshut mode 0:CRU 1:GPIO */
> + rockchip,hw-tshut-mode = <1>;
> + /* tshut polarity 0:LOW 1:HIGH */
> + rockchip,hw-tshut-polarity = <1>;
> + status = "okay";
> +};
> +
> +&u2phy0 {
> + status = "okay";
> +
> + u2phy0_otg: otg-port {
> + status = "okay";
> + };
> +
> + u2phy0_host: host-port {
> + status = "okay";
> + phy-supply = <&vcc5v0_sys>;
> + };
> +
> + port {
> + u2phy0_typec_hs: endpoint {
> + remote-endpoint = <&usbc_hs>;
> + };
> + };
> +};
> +
> +&u2phy1 {
> + status = "okay";
> +
> + u2phy1_otg: otg-port {
> + status = "okay";
> + };
> +
> + u2phy1_host: host-port {
> + status = "okay";
> + phy-supply = <&vcc5v0_sys>;
> + };
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
> + uart-has-rtscts;
> + status = "okay";
> +
> + // Per "WIFI/BT MODULE", page 19.
> + bluetooth {
> + compatible = "brcm,bcm4345c5";
> + clocks = <&rk818 1>;
> + clock-names = "lpo";
> + device-wakeup-gpios = <&gpio2 RK_PD2 GPIO_ACTIVE_HIGH>;
> + host-wakeup-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_HIGH>;
> + max-speed = <1500000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&bt_host_wake_l &bt_wake_l &bt_enable_h>;
> + shutdown-gpios = <&gpio0 RK_PB1 GPIO_ACTIVE_HIGH>;
> + vbat-supply = <&wifi_bat>;
> + vddio-supply = <&vcc_wl>;
> + };
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&usb_host0_ehci {
> + status = "okay";
> +};
> +
> +&usb_host0_ohci {
> + status = "okay";
> +};
> +
> +&usb_host1_ehci {
> + status = "okay";
> +};
> +
> +&usb_host1_ohci {
> + status = "okay";
> +};
> +
> +&usbdrd3_0 {
> + status = "okay";
> +};
> +
> +&usbdrd_dwc3_0 {
> + dr_mode = "peripheral";
> + status = "okay";
> +};
> +
> +&vopb {
> + status = "okay";
> +};
> +
> +&vopb_mmu {
> + status = "okay";
> +};
> +
> +&vopl {
> + status = "okay";
> +};
> +
> +&vopl_mmu {
> + status = "okay";
> +};
> --
> 2.36.0
>
More information about the Linux-rockchip
mailing list