[PATCH 3/3] arm64: dts: rockchip: add Anbernic RG353 and RG503
Maya Matuszczyk
maccraft123mc at gmail.com
Thu Aug 18 02:49:12 PDT 2022
Thanks for the patch,
but I see some things that could be improved.
śr., 17 sie 2022 o 22:50 Chris Morgan <macroalpha82 at gmail.com> napisał(a):
>
> From: Chris Morgan <macromorgan at hotmail.com>
>
> Anbernic RG353 and RG503 are both RK3566 based handheld gaming devices
> from Anbernic.
>
> Both devices have:
> - 2 SDMMC slots
> - A Realtek rtl8821cs WiFi/Bluetooth adapter
> - A mini HDMI port
> - A USB C host port and a USB C otg port (currently only working as
> device).
IIRC if you force that dual role port to work as a host it will work fine.
> - Multiple GPIO buttons and a single ADC button.
> - Dual analog joysticks controlled via a GPIO mux.
> - A headphone jack with amplified stereo speakers.
A PWM-controller vbibration motor too.
>
> The RG353 has:
> - 2GB LPDDR4 RAM
> - A 32GB eMMC
> - A 3.5 inch 640x480 4-lane DSI panel of unknown origin with an i2c
> controlled touchscreen.
I wasn't able to find the part number of the panel, nor the manufacturer.
It might be a custom made part.
On the flex PCB there are markings:
"YLM-355604-B-A1", underneath it in smaller font is "2201",
and on the other side, much less visible, "WL-355604-A1".
I tried disassembling the panle itself, and there were
still no markings. :/
The touchscreen is a Hynitron CST340.
This device also has a SGM4865 audio amplifier,
>
> The RG503 has:
> - 1GB LPDDR4 RAM
> - A 5 inch 960x544 AMOLED 2-lane DSI/DBI panel manufactured by Samsung
> with part number ams495qa04. Data for this panel is provided via the
> DSI interface, however commands are sent via a 9-bit 3-wire SPI
> interface. The MISO pin of SPI3 of the SOC is wired to the input of
> the panel, so it must be bitbanged.
>
> This devicetree enables the following hardware:
> - HDMI (plus audio)
> - Analog audio, including speakers.
> - All buttons
> - All SDMMC/eMMC/SDIO controllers
> - The ADC joysticks (note a pending patch is required to use them)
>
> The following hardware is not enabled:
> - The display panels (drivers are being written and there are issues
> with the upstream DSI and VOP2 subsystems).
> - Battery (driver pending).
> - WiFi/Bluetooth (the drivers are not mainline, however they can be
> built and probed out-of-tree).
Maybe we could still include dose in dts file, as it's supposed to
describe the hardware?
>
> Signed-off-by: Chris Morgan <macromorgan at hotmail.com>
> ---
> arch/arm64/boot/dts/rockchip/Makefile | 2 +
> .../dts/rockchip/rk3566-anbernic-rg353.dts | 103 +++
> .../dts/rockchip/rk3566-anbernic-rg503.dts | 93 ++
> .../dts/rockchip/rk3566-anbernic-rgxx3.dtsi | 807 ++++++++++++++++++
> 4 files changed, 1005 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg353.dts
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg503.dts
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-anbernic-rgxx3.dtsi
>
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index ef79a672804a..228b4ec4b773 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -57,6 +57,8 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-rockpro64.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-sapphire.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-sapphire-excavator.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399pro-rock-pi-n10.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-anbernic-rg353.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-anbernic-rg503.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-pinenote-v1.1.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-pinenote-v1.2.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-quartz64-a.dtb
> diff --git a/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg353.dts b/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg353.dts
> new file mode 100644
> index 000000000000..8c6252b63774
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg353.dts
> @@ -0,0 +1,103 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/pinctrl/rockchip.h>
> +#include "rk3566-anbernic-rgxx3.dtsi"
> +
> +/ {
> + model = "RG353";
> + compatible = "anbernic,rg353", "rockchip,rk3566";
> +
> + aliases {
> + mmc0 = &sdhci;
> + mmc1 = &sdmmc0;
> + mmc2 = &sdmmc1;
> + mmc3 = &sdmmc2;
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + power-supply = <&vcc_sys>;
> + pwms = <&pwm4 0 25000 0>;
> + };
> +};
> +
> +&gpio_keys {
> + button-5 {
Maybe it could be named in a way that would
be more in-line with what the button actually is, instead
of a random number?
> + gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_LOW>;
> + label = "DPAD-LEFT";
> + linux,code = <BTN_DPAD_RIGHT>;
> + };
> +
> + button-6 {
> + gpios = <&gpio3 RK_PA6 GPIO_ACTIVE_LOW>;
> + label = "DPAD-RIGHT";
> + linux,code = <BTN_DPAD_LEFT>;
> + };
> +
> + button-11 {
> + gpios = <&gpio3 RK_PB3 GPIO_ACTIVE_LOW>;
> + label = "TR";
> + linux,code = <BTN_TR2>;
> + };
> +
> + button-12 {
> + gpios = <&gpio3 RK_PB4 GPIO_ACTIVE_LOW>;
> + label = "TR2";
> + linux,code = <BTN_TR>;
> + };
> +
> + button-16 {
> + gpios = <&gpio3 RK_PC1 GPIO_ACTIVE_LOW>;
> + label = "WEST";
> + linux,code = <BTN_WEST>;
> + };
> +
> + button-17 {
> + gpios = <&gpio3 RK_PC2 GPIO_ACTIVE_LOW>;
> + label = "EAST";
> + linux,code = <BTN_EAST>;
> + };
> +};
> +
> +&i2c0 {
> + /* This hardware is physically present but unused. */
> + cw2015 at 62 {
> + compatible = "cellwise,cw2015";
> + reg = <0x62>;
> + status = "disabled";
> + };
> +};
> +
> +&i2c2 {
> + pintctrl-names = "default";
> + pinctrl-0 = <&i2c2m1_xfer>;
> + status = "okay";
> +};
> +
> +&pinctrl {
> + gpio-lcd {
> + lcd_rst: lcd-rst {
> + rockchip,pins =
> + <4 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +};
> +
> +&pwm4 {
> + status = "okay";
> +};
> +
> +&sdhci {
> + pinctrl-0 = <&emmc_bus8>, <&emmc_clk>, <&emmc_cmd>, <&emmc_datastrobe>, <&emmc_rstnout>;
> + pinctrl-names = "default";
> + bus-width = <8>;
> + mmc-hs200-1_8v;
> + non-removable;
> + vmmc-supply = <&vcc_3v3>;
> + vqmmc-supply = <&vcc_1v8>;
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg503.dts b/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg503.dts
> new file mode 100644
> index 000000000000..c5941d405d14
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg503.dts
> @@ -0,0 +1,93 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/pinctrl/rockchip.h>
> +#include "rk3566-anbernic-rgxx3.dtsi"
> +
> +/ {
> + model = "RG503";
> + compatible = "anbernic,rg503", "rockchip,rk3566";
> +
> + aliases {
> + mmc0 = &sdmmc0;
> + mmc1 = &sdmmc1;
> + mmc2 = &sdmmc2;
> + };
> +
> + gpio_spi: spi {
> + compatible = "spi-gpio";
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi_pins>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + sck-gpios = <&gpio4 RK_PB3 GPIO_ACTIVE_HIGH>;
> + mosi-gpios = <&gpio4 RK_PB0 GPIO_ACTIVE_HIGH>;
> + cs-gpios = <&gpio4 RK_PA7 GPIO_ACTIVE_HIGH>;
> + num-chipselects = <0>;
> + };
> +};
> +
> +&gpio_keys {
> + button-5 {
> + gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_LOW>;
> + label = "DPAD-LEFT";
> + linux,code = <BTN_DPAD_LEFT>;
> + };
> +
> + button-6 {
> + gpios = <&gpio3 RK_PA6 GPIO_ACTIVE_LOW>;
> + label = "DPAD-RIGHT";
> + linux,code = <BTN_DPAD_RIGHT>;
> + };
> +
> + button-11 {
> + gpios = <&gpio3 RK_PB3 GPIO_ACTIVE_LOW>;
> + label = "TR";
> + linux,code = <BTN_TR>;
> + };
> +
> + button-12 {
> + gpios = <&gpio3 RK_PB4 GPIO_ACTIVE_LOW>;
> + label = "TR2";
> + linux,code = <BTN_TR2>;
> + };
> +
> + button-16 {
> + gpios = <&gpio3 RK_PC1 GPIO_ACTIVE_LOW>;
> + label = "EAST";
> + linux,code = <BTN_EAST>;
> + };
> +
> + button-17 {
> + gpios = <&gpio3 RK_PC2 GPIO_ACTIVE_LOW>;
> + label = "WEST";
> + linux,code = <BTN_WEST>;
> + };
> +};
> +
> +&pinctrl {
> + gpio-spi {
> + spi_pins: spi-pins {
> + rockchip,pins =
> + <4 RK_PA7 RK_FUNC_GPIO &pcfg_pull_none>,
> + <4 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>,
> + <4 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + gpio-lcd {
> + lcd_enable: lcd-enable {
> + rockchip,pins =
> + <4 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + lcd_reset: lcd-reset {
> + rockchip,pins =
> + <4 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +};
> diff --git a/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rgxx3.dtsi b/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rgxx3.dtsi
> new file mode 100644
> index 000000000000..4b03a677f6dc
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rgxx3.dtsi
> @@ -0,0 +1,807 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/pinctrl/rockchip.h>
> +#include <dt-bindings/soc/rockchip,vop2.h>
> +#include "rk3566.dtsi"
> +
> +/ {
> + chosen: chosen {
> + stdout-path = "serial2:1500000n8";
> + };
> +
> + adc-joystick {
> + compatible = "adc-joystick";
> + io-channels = <&adc_mux 0>,
> + <&adc_mux 1>,
> + <&adc_mux 2>,
> + <&adc_mux 3>;
> + pinctrl-0 = <&joy_mux_en>;
> + pinctrl-names = "default";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + axis at 0 {
> + reg = <0>;
> + abs-flat = <32>;
> + abs-fuzz = <32>;
> + abs-range = <1023 15>;
> + linux,code = <ABS_X>;
> + };
> +
> + axis at 1 {
> + reg = <1>;
> + abs-flat = <32>;
> + abs-fuzz = <32>;
> + abs-range = <15 1023>;
> + linux,code = <ABS_RX>;
> + };
> +
> + axis at 2 {
> + reg = <2>;
> + abs-flat = <32>;
> + abs-fuzz = <32>;
> + abs-range = <15 1023>;
> + linux,code = <ABS_Y>;
> + };
> +
> + axis at 3 {
> + reg = <3>;
> + abs-flat = <32>;
> + abs-fuzz = <32>;
> + abs-range = <1023 15>;
> + linux,code = <ABS_RY>;
> + };
> + };
> +
> + adc_keys: adc-keys {
> + compatible = "adc-keys";
> + io-channels = <&saradc 0>;
> + io-channel-names = "buttons";
> + keyup-threshold-microvolt = <1800000>;
> + poll-interval = <60>;
> +
> + button-mode {
> + label = "MODE";
> + linux,code = <BTN_MODE>;
> + press-threshold-microvolt = <1750>;
> + };
> + };
> +
> + adc_mux: adc-mux {
> + compatible = "io-channel-mux";
> + channels = "left_x", "right_x", "left_y", "right_y";
> + io-channels = <&saradc 3>;
> + io-channel-names = "parent";
> + mux-controls = <&gpio_mux>;
> + settle-time-us = <100>;
> + #io-channel-cells = <1>;
> + };
> +
> + gpio_keys: gpio-keys {
> + compatible = "gpio-keys";
> + pinctrl-0 = <&btn_pins>;
> + pinctrl-names = "default";
> +
> + button-1 {
> + gpios = <&gpio3 RK_PA1 GPIO_ACTIVE_LOW>;
> + label = "THUMBL";
> + linux,code = <BTN_THUMBL>;
> + };
> +
> + button-2 {
> + gpios = <&gpio3 RK_PA2 GPIO_ACTIVE_LOW>;
> + label = "THUMBR";
> + linux,code = <BTN_THUMBR>;
> + };
> +
> + button-3 {
> + gpios = <&gpio3 RK_PA3 GPIO_ACTIVE_LOW>;
> + label = "DPAD-UP";
> + linux,code = <BTN_DPAD_UP>;
> + };
> +
> + button-4 {
> + gpios = <&gpio3 RK_PA4 GPIO_ACTIVE_LOW>;
> + label = "DPAD-DOWN";
> + linux,code = <BTN_DPAD_DOWN>;
> + };
> +
> + button-7 {
> + gpios = <&gpio3 RK_PA7 GPIO_ACTIVE_LOW>;
> + label = "VOLUMEUP";
> + linux,code = <KEY_VOLUMEUP>;
> + };
> +
> + button-8 {
> + gpios = <&gpio3 RK_PB0 GPIO_ACTIVE_LOW>;
> + label = "VOLUMEDOWN";
> + linux,code = <KEY_VOLUMEDOWN>;
> + };
> +
> + button-9 {
> + gpios = <&gpio3 RK_PB1 GPIO_ACTIVE_LOW>;
> + label = "TL";
> + linux,code = <BTN_TL>;
> + };
> +
> + button-10 {
> + gpios = <&gpio3 RK_PB2 GPIO_ACTIVE_LOW>;
> + label = "TL2";
> + linux,code = <BTN_TL2>;
> + };
> +
> + button-13 {
> + gpios = <&gpio3 RK_PB5 GPIO_ACTIVE_LOW>;
> + label = "START";
> + linux,code = <BTN_START>;
> + };
> +
> + button-14 {
> + gpios = <&gpio3 RK_PB6 GPIO_ACTIVE_LOW>;
> + label = "SELECT";
> + linux,code = <BTN_SELECT>;
> + };
> +
> + button-15 {
> + gpios = <&gpio3 RK_PC0 GPIO_ACTIVE_LOW>;
> + label = "NORTH";
> + linux,code = <BTN_NORTH>;
> + };
> +
> + button-18 {
> + gpios = <&gpio3 RK_PC3 GPIO_ACTIVE_LOW>;
> + label = "SOUTH";
> + linux,code = <BTN_SOUTH>;
> + };
> + };
> +
> + gpio_mux: mux-controller {
> + compatible = "gpio-mux";
> + mux-gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_LOW>,
> + <&gpio0 RK_PB7 GPIO_ACTIVE_LOW>;
> + #mux-control-cells = <0>;
> + };
> +
> + hdmi-con {
> + compatible = "hdmi-connector";
> + type = "c";
> +
> + port {
> + hdmi_con_in: endpoint {
> + remote-endpoint = <&hdmi_out_con>;
> + };
> + };
> + };
> +
> + leds: gpio-leds {
> + compatible = "gpio-leds";
> + pinctrl-0 = <&led_pins>;
> + pinctrl-names = "default";
> +
> + green_led: led-0 {
> + color = <LED_COLOR_ID_GREEN>;
> + default-state = "on";
> + function = LED_FUNCTION_POWER;
> + gpios = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
> + };
> +
> + amber_led: led-1 {
> + color = <LED_COLOR_ID_AMBER>;
> + function = LED_FUNCTION_CHARGING;
> + gpios = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
> + retain-state-suspended;
> + };
> +
> + red_led: led-2 {
> + color = <LED_COLOR_ID_RED>;
> + default-state = "off";
> + function = LED_FUNCTION_STATUS;
> + gpios = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + rk817-sound {
> + compatible = "simple-audio-card";
> + simple-audio-card,name = "anbernic_rk817";
> + simple-audio-card,aux-devs = <&spk_amp>;
> + simple-audio-card,format = "i2s";
> + simple-audio-card,hp-det-gpio = <&gpio4 RK_PC6 GPIO_ACTIVE_HIGH>;
> + simple-audio-card,mclk-fs = <256>;
> + simple-audio-card,widgets =
> + "Microphone", "Mic Jack",
> + "Headphone", "Headphones",
> + "Speaker", "Internal Speakers";
> + simple-audio-card,routing =
> + "MICL", "Mic Jack",
> + "Headphones", "HPOL",
> + "Headphones", "HPOR",
> + "Internal Speakers", "Speaker Amp OUTL",
> + "Internal Speakers", "Speaker Amp OUTR",
> + "Speaker Amp INL", "HPOL",
> + "Speaker Amp INR", "HPOR";
> + simple-audio-card,pin-switches = "Internal Speakers";
> +
> + simple-audio-card,codec {
> + sound-dai = <&rk817>;
> + };
> +
> + simple-audio-card,cpu {
> + sound-dai = <&i2s1_8ch>;
> + };
> + };
> +
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + clocks = <&rk817 1>;
> + clock-names = "ext_clock";
> + pinctrl-0 = <&wifi_enable_h>;
> + pinctrl-names = "default";
> + post-power-on-delay-ms = <200>;
> + reset-gpios = <&gpio4 RK_PA2 GPIO_ACTIVE_LOW>;
> + };
> +
> + spk_amp: audio-amplifier {
> + compatible = "simple-audio-amplifier";
> + enable-gpios = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>;
> + pinctrl-0 = <&spk_amp_enable_h>;
> + pinctrl-names = "default";
> + sound-name-prefix = "Speaker Amp";
> + };
> +
> + vcc3v3_lcd0_n: vcc3v3-lcd0-n {
> + compatible = "regulator-fixed";
> + gpio = <&gpio0 RK_PC2 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + pinctrl-0 = <&vcc_lcd_h>;
> + pinctrl-names = "default";
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc3v3_lcd0_n";
> + vin-supply = <&vcc_3v3>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_sys: vcc_sys {
> + compatible = "regulator-fixed";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3800000>;
> + regulator-max-microvolt = <3800000>;
> + regulator-name = "vcc_sys";
> + };
> +
> + vcc_wifi: vcc-wifi {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio0 RK_PA0 GPIO_ACTIVE_HIGH>;
> + pinctrl-0 = <&vcc_wifi_h>;
> + pinctrl-names = "default";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc_wifi";
> + };
> +
> + vibrator: pwm-vibrator {
> + compatible = "pwm-vibrator";
> + pwm-names = "enable";
> + pwms = <&pwm5 0 1000000000 0>;
> + };
> +};
> +
> +&combphy1 {
> + status = "okay";
> +};
> +
> +&cpu0 {
> + cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu1 {
> + cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu2 {
> + cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu3 {
> + cpu-supply = <&vdd_cpu>;
> +};
> +
> +&gpu {
> + mali-supply = <&vdd_gpu>;
> + status = "okay";
> +};
> +
> +&hdmi {
> + status = "okay";
> +};
> +
> +&hdmi_in {
> + hdmi_in_vp0: endpoint {
> + remote-endpoint = <&vp0_out_hdmi>;
> + };
> +};
> +
> +&hdmi_out {
> + hdmi_out_con: endpoint {
> + remote-endpoint = <&hdmi_con_in>;
> + };
> +};
> +
> +&hdmi_sound {
> + status = "okay";
> +};
> +
> +&i2c0 {
> + status = "okay";
> +
> + rk817: pmic at 20 {
> + compatible = "rockchip,rk817";
> + reg = <0x20>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
> + clock-output-names = "rk808-clkout1", "rk808-clkout2";
> + clock-names = "mclk";
> + clocks = <&cru I2S1_MCLKOUT_TX>;
> + assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
> + assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
> + #clock-cells = <1>;
> + #sound-dai-cells = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2s1m0_mclk>, <&pmic_int_l>;
> + wakeup-source;
> +
> + vcc1-supply = <&vcc_sys>;
> + vcc2-supply = <&vcc_sys>;
> + vcc3-supply = <&vcc_sys>;
> + vcc4-supply = <&vcc_sys>;
> + vcc5-supply = <&vcc_sys>;
> + vcc6-supply = <&vcc_sys>;
> + vcc7-supply = <&vcc_sys>;
> + vcc8-supply = <&vcc_sys>;
> + vcc9-supply = <&dcdc_boost>;
> +
> + regulators {
> + vdd_logic: DCDC_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <500000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-init-microvolt = <900000>;
> + regulator-ramp-delay = <6001>;
> + regulator-initial-mode = <0x2>;
> + regulator-name = "vdd_logic";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + regulator-suspend-microvolt = <900000>;
> + };
> + };
> +
> + vdd_gpu: DCDC_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <500000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-init-microvolt = <900000>;
> + regulator-ramp-delay = <6001>;
> + regulator-initial-mode = <0x2>;
> + regulator-name = "vdd_gpu";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_ddr: DCDC_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-initial-mode = <0x2>;
> + regulator-name = "vcc_ddr";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc_3v3: DCDC_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-initial-mode = <0x2>;
> + regulator-name = "vcc_3v3";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vcca1v8_pmu: LDO_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcca1v8_pmu";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vdda_0v9: LDO_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <900000>;
> + regulator-name = "vdda_0v9";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdda0v9_pmu: LDO_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <900000>;
> + regulator-name = "vdda0v9_pmu";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <900000>;
> + };
> + };
> +
> + vccio_acodec: LDO_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vccio_acodec";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vccio_sd: LDO_REG5 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vccio_sd";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc3v3_pmu: LDO_REG6 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc3v3_pmu";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vcc_1v8: LDO_REG7 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc_1v8";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc1v8_dvp: LDO_REG8 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc1v8_dvp";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc2v8_dvp: LDO_REG9 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + regulator-name = "vcc2v8_dvp";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + dcdc_boost: BOOST {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <4700000>;
> + regulator-max-microvolt = <5400000>;
> + regulator-name = "boost";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + otg_switch: OTG_SWITCH {
> + regulator-name = "otg_switch";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> + };
> + };
> +
> + vdd_cpu: regulator at 40 {
> + compatible = "fcs,fan53555";
> + reg = <0x40>;
> + fcs,suspend-voltage-selector = <1>;
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <712500>;
> + regulator-max-microvolt = <1390000>;
> + regulator-init-microvolt = <900000>;
> + regulator-name = "vdd_cpu";
> + regulator-ramp-delay = <2300>;
> + vin-supply = <&vcc_sys>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +};
> +
> +&i2c1 {
> + /* Unknown/unused device at 0x3c */
I can try poking around my RG353P and RG503
motherboards to see what that device actually is.
> + status = "disabled";
> +};
> +
> +&i2s0_8ch {
> + status = "okay";
> +};
> +
> +&i2s1_8ch {
> + pinctrl-0 = <&i2s1m0_sclktx
> + &i2s1m0_lrcktx
> + &i2s1m0_sdi0
> + &i2s1m0_sdo0>;
> + pinctrl-names = "default";
> + rockchip,trcm-sync-tx-only;
> + status = "okay";
> +};
> +
> +&pinctrl {
> +
> + audio-amplifier {
> + spk_amp_enable_h: spk-amp-enable-h {
> + rockchip,pins =
> + <4 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + gpio-btns {
> + btn_pins: btn-pins {
> + rockchip,pins =
> + <3 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PA7 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PB1 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PB3 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PB4 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PB5 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PB6 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PB7 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PC0 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PC1 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PC2 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PC3 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +
> + gpio-led {
> + led_pins: led-pins {
> + rockchip,pins =
> + <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>,
> + <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>,
> + <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + joy-mux {
> + joy_mux_en: joy-mux-en {
> + rockchip,pins =
> + <0 RK_PB5 RK_FUNC_GPIO &pcfg_output_low>;
> + };
> + };
> +
> + pmic {
> + pmic_int_l: pmic-int-l {
> + rockchip,pins =
> + <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +
> + sdio-pwrseq {
> + wifi_enable_h: wifi-enable-h {
> + rockchip,pins =
> + <4 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + vcc3v3_lcd {
> + vcc_lcd_h: vcc_lcd_h {
> + rockchip,pins =
> + <0 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + vcc-wifi {
> + vcc_wifi_h: vcc_wifi_h {
> + rockchip,pins =
> + <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +};
> +
> +&pmu_io_domains {
> + status = "okay";
> + pmuio1-supply = <&vcc3v3_pmu>;
> + pmuio2-supply = <&vcc3v3_pmu>;
> + vccio1-supply = <&vccio_acodec>;
> + vccio3-supply = <&vccio_sd>;
> + vccio4-supply = <&vcc_1v8>;
> + vccio5-supply = <&vcc_3v3>;
> + vccio6-supply = <&vcc1v8_dvp>;
> + vccio7-supply = <&vcc_3v3>;
> +};
> +
> +&pwm5 {
> + status = "okay";
> +};
> +
> +&saradc {
> + vref-supply = <&vcc_1v8>;
> + status = "okay";
> +};
> +
> +&sdmmc0 {
> + bus-width = <4>;
> + cap-sd-highspeed;
> + cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
> + disable-wp;
> + pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
> + pinctrl-names = "default";
> + sd-uhs-sdr104;
> + vmmc-supply = <&vcc_3v3>;
> + vqmmc-supply = <&vccio_sd>;
> + status = "okay";
> +};
> +
> +&sdmmc1 {
> + bus-width = <4>;
> + cap-sd-highspeed;
> + cd-gpios = <&gpio2 RK_PB2 GPIO_ACTIVE_LOW>;
> + disable-wp;
> + pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk &sdmmc1_det>;
> + pinctrl-names = "default";
> + sd-uhs-sdr104;
> + vmmc-supply = <&vcc_3v3>;
> + vqmmc-supply = <&vcc1v8_dvp>;
> + status = "okay";
> +};
> +
> +&sdmmc2 {
> + bus-width = <4>;
> + cap-sd-highspeed;
> + cap-sdio-irq;
> + keep-power-in-suspend;
> + mmc-pwrseq = <&sdio_pwrseq>;
> + non-removable;
> + pinctrl-0 = <&sdmmc2m0_bus4 &sdmmc2m0_cmd &sdmmc2m0_clk>;
> + pinctrl-names = "default";
> + vmmc-supply = <&vcc_wifi>;
> + vqmmc-supply = <&vcca1v8_pmu>;
> + status = "okay";
> +};
> +
> +&tsadc {
> + rockchip,hw-tshut-mode = <1>;
> + rockchip,hw-tshut-polarity = <0>;
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-0 = <&uart1m1_xfer &uart1m1_ctsn &uart1m1_rtsn>;
> + pinctrl-names = "default";
> + uart-has-rtscts;
> + status = "okay";
> +
> + bluetooth {
> + compatible = "realtek,rtl8821cs-bt";
> + device-wake-gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>;
> + enable-gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>;
> + host-wake-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>;
> + };
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +/*
> + * Lack the schematics to verify, but port works as a peripheral
> + * (and not a host or OTG port).
> + */
Maybe it's just missing a usb-c-connector node?
It would be useful to have in this devicetree.
> +&usb_host0_xhci {
> + dr_mode = "peripheral";
> + phys = <&usb2phy0_otg>;
> + phy-names = "usb2-phy";
> + status = "okay";
> +};
Best Regards,
Maya Matuszczyk
More information about the Linux-rockchip
mailing list