[PATCH v6 1/8] dt-bindings: rockchip-sfc: Bindings for Rockchip serial flash controller
Jon Lin
jon.lin at rock-chips.com
Tue Jun 8 20:50:12 PDT 2021
On 6/9/21 2:03 AM, Johan Jonker wrote:
> Hi Jon,
>
> A look at the build log shows this error:
>
> https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20210608022644.21074-2-jon.lin@rock-chips.com/
>
> dtschema/dtc warnings/errors:
> /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.example.dt.yaml:
> spi at ff3a0000: clock-names:0: 'hclk_sfc' was expected
> From schema:
> /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml
> /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.example.dt.yaml:
> spi at ff3a0000: clock-names:1: 'clk_sfc' was expected
> From schema:
> /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml
>
> Check document with:
>
> make ARCH=arm dt_binding_check
> DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/rockchip-sfc.yaml
>
> make ARCH=arm dtbs_check
> DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/rockchip-sfc.yaml
>
> make ARCH=arm64 dtbs_check
> DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/rockchip-sfc.yaml
>
> Remove any errors before submitting.
>
> ===
>
> Johan
>
> On 6/8/21 4:26 AM, Jon Lin wrote:
>> From: Chris Morgan <macromorgan at hotmail.com>
>>
>> Add bindings for the Rockchip serial flash controller. New device
>> specific parameter of rockchip,sfc-no-dma included in documentation.
>>
>> Signed-off-by: Chris Morgan <macromorgan at hotmail.com>
>> Signed-off-by: Jon Lin <jon.lin at rock-chips.com>
>> ---
>>
>> Changes in v6:
>> - Add support in device trees for rv1126(Declared in series 5 but not
>> submitted)
>> - Change to use "clk_sfc" "hclk_sfc" as clock lable, since it does not
>> affect interpretation and has been widely used
>> - Support sfc tx_dual, tx_quad(Declared in series 5 but not submitted)
>> - Simplify the code, such as remove "rockchip_sfc_register_all"(Declared
>> in series 5 but not submitted)
>> - Support SFC ver4 ver5(Declared in series 5 but not submitted)
>> - Add author Chris Morgan and Jon Lin to spi-rockchip-sfc.c
>> - Change to use devm_spi_alloc_master and spi_unregister_master
>>
>> Changes in v5:
>> - Add support in device trees for rv1126
>> - Support sfc tx_dual, tx_quad
>> - Simplify the code, such as remove "rockchip_sfc_register_all"
>> - Support SFC ver4 ver5
>>
>> Changes in v4:
>> - Changing patch back to an "RFC". An engineer from Rockchip
>> reached out to me to let me know they are working on this patch for
>> upstream, I am submitting this v4 for the community to see however
>> I expect Jon Lin (jon.lin at rock-chips.com) will submit new patches
>> soon and these are the ones we should pursue for mainlining. Jon's
>> patch series should include support for more hardware than this
>> series.
>> - Clean up documentation more and ensure it is correct per
>> make dt_binding_check.
>> - Add support in device trees for rk3036, rk3308, and rv1108.
>> - Add ahb clock (hclk_sfc) support for rk3036.
>> - Change rockchip_sfc_wait_fifo_ready() to use a switch statement.
>> - Change IRQ code to only mark IRQ as handled if it handles the
>> specific IRQ (DMA transfer finish) it is supposed to handle.
>>
>> Changes in v3:
>> - Changed the name of the clocks to sfc/ahb (from clk-sfc/clk-hsfc).
>> - Changed the compatible string from rockchip,sfc to
>> rockchip,rk3036-sfc. A quick glance at the datasheets suggests this
>> driver should work for the PX30, RK180x, RK3036, RK312x, RK3308 and
>> RV1108 SoCs, and possibly more. However, I am currently only able
>> to test this on a PX30 (an RK3326). The technical reference manuals
>> appear to list the same registers for each device.
>> - Corrected devicetree documentation for formatting and to note these
>> changes.
>> - Replaced the maintainer with Heiko Stuebner and myself, as we will
>> take ownership of this going forward.
>> - Noted that the device (per the reference manual) supports 4 CS, but
>> I am only able to test a single CS (CS 0).
>> - Reordered patches to comply with upstream rules.
>>
>> Changes in v2:
>> - Reimplemented driver using spi-mem subsystem.
>> - Removed power management code as I couldn't get it working properly.
>> - Added device tree bindings for Odroid Go Advance.
>>
>> Changes in v1:
>> hanges made in this new series versus the v8 of the old series:
>> - Added function to read spi-rx-bus-width from device tree, in the
>> event that the SPI chip supports 4x mode but only has 2 pins
>> wired (such as the Odroid Go Advance).
>> - Changed device tree documentation from txt to yaml format.
>> - Made "reset" message a dev_dbg from a dev_info.
>> - Changed read and write fifo functions to remove redundant checks.
>> - Changed the write and read from relaxed to non-relaxed when
>> starting the DMA transfer or reading the DMA IRQ.
>> - Changed from dma_coerce_mask_and_coherent to just
>> dma_set_mask_and_coherent.
>> - Changed name of get_if_type to rockchip_sfc_get_if_type.
>>
>> .../devicetree/bindings/spi/rockchip-sfc.yaml | 87 +++++++++++++++++++
>> 1 file changed, 87 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/spi/rockchip-sfc.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml b/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml
>> new file mode 100644
>> index 000000000000..160449713f97
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml
>> @@ -0,0 +1,87 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/spi/rockchip-sfc.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Rockchip Serial Flash Controller (SFC)
>> +
>> +maintainers:
>> + - Heiko Stuebner <heiko at sntech.de>
>> + - Chris Morgan <macromorgan at hotmail.com>
> In the driver spi-rockchip-sfc.c is used:
> Chris Morgan <macroalpha82 at gmail.com>
> Maybe use a consistent email address?
> Also Hotmail does strange things to message-ID's and links/content
> inside patches.
>
>> +
>> +allOf:
>> + - $ref: spi-controller.yaml#
>> +
>> +properties:
>> + compatible:
>> + oneOf:
>> + - const: rockchip,rk3036-sfc
>> + - items:
>> + - enum:
>> + - rockchip,px30-sfc
>> + - rockchip,rk3308-sfc
>> + - rockchip,rv1108-sfc
>> + - const: rockchip,rk3036-sfc
>> + - const: rockchip,rv1126-sfc
> A look at the driver shows this:
>
> +static const struct of_device_id rockchip_sfc_dt_ids[] = {
>
> + { .compatible = "rockchip,px30-sfc"},
>
> remove
>
> + { .compatible = "rockchip,rk3036-sfc"},
>
> + { .compatible = "rockchip,rk3308-sfc"},
> + { .compatible = "rockchip,rv1126-sfc"},
>
> remove
>
> + { /* sentinel */ }
> +};
>
> When no '.data = &my_sfc_data' exist then there's no need for additional
> compatible strings in the driver.
> ===
> example for I2S:
> { .compatible = "rockchip,rk3399-i2s", .data = &rk3399_i2s_pins },
> ===
> Compatibility strings are supposed to be SoC orientated.
> With rockchip_sfc_get_version() all we need is one fall back string for
> now I think. Is rk3568 identical. Please advise.
>
>
> - const: rockchip,rk3036-sfc
> - items:
> - enum:
> - rockchip,px30-sfc
> - rockchip,rk3308-sfc
> - rockchip,rk3368-sfc
> - rockchip,rk3568-sfc
> - rockchip,rv1108-sfc
> - rockchip,rv1126-sfc
> - const: rockchip,rk3036-sfc
>
> ===
>
> The rk3368 TRM also describes a SFC controller.
> For the mainline DT completeness is it possible to add a rk3368 SFC node
> as well? ;)
>
>> +
>> + reg:
>> + maxItems: 1
>> +
>> + interrupts:
>> + maxItems: 1
>> +
>> + clocks:
>> + items:
>> + - description: Bus Clock
>> + - description: Module Clock
>> +
>> + clock-names:
>> + items:
>> + - const: hclk_sfc
>> + - const: clk_sfc
>> +
>> + power-domains:
>> + maxItems: 1
>> +
>> + rockchip,sfc-no-dma:
>> + description: Disable DMA and utilize FIFO mode only
>> + type: boolean
>> +
>> +required:
>> + - compatible
>> + - reg
>> + - interrupts
>> + - clocks
>> + - clock-names
>> +
>> +unevaluatedProperties: false
>> +
>> +examples:
>> + - |
>> + #include <dt-bindings/clock/px30-cru.h>
>> + #include <dt-bindings/interrupt-controller/arm-gic.h>
>> + #include <dt-bindings/power/px30-power.h>
>> +
>> + sfc: spi at ff3a0000 {
>> + compatible = "rockchip,px30-sfc","rockchip,rk3036-sfc";
>> + reg = <0xff3a0000 0x4000>;
>> + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&cru SCLK_SFC>, <&cru HCLK_SFC>;
>> + clock-names = "clk_sfc", "hclk_sfc";
> The clocks in the examples and dtsi files must have the same sort order.
>
>> + pinctrl-0 = <&sfc_clk &sfc_cs &sfc_bus2>;
>> + pinctrl-names = "default";
>> + power-domains = <&power PX30_PD_MMC_NAND>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + flash at 0 {
> >From spi-controller.yaml:
>
> patternProperties:
> "^.*@[0-9a-f]+$":
> type: object
>
> properties:
> compatible:
> description:
> Compatible of the SPI device.
>
> reg:
> minimum: 0
>
> maximum: 256
>
> description:
> Chip select used by the device.
>
> This allows 257 sub nodes.
> Support up to 4 chip select in the driver.
> #define SFC_MAX_CHIPSELECT_NUM 4
RK SFC design is up to 4 CS.
Sorry, I don't see any specific improvement in this comment, can you
explain it in detail.
>
>> + compatible = "jedec,spi-nor";
>> + reg = <0>;
>> + spi-max-frequency = <108000000>;
>> + spi-rx-bus-width = <2>;
>> + spi-tx-bus-width = <2>;
>> + };
>> + };
>> +
>> +...
>>
>
>
More information about the Linux-rockchip
mailing list