[PATCH v3 2/2] rockchip: rk3328: Add support for FriendlyARM NanoPi R2S
David Bauer
mail at david-bauer.net
Sun Sep 20 11:45:28 EDT 2020
This adds support for the NanoPi R2S from FriendlyARM.
Rockchip RK3328 SoC
1GB DDR4 RAM
Gigabit Ethernet (WAN)
Gigabit Ethernet (USB3) (LAN)
USB 2.0 Host Port
MicroSD slot
Reset button
WAN - LAN - SYS LED
Signed-off-by: David Bauer <mail at david-bauer.net>
---
Changes in v3:
- Rename gmac-clock node
- Various sorting fixes
- Rename label for reset button
- Fix LED pinctrl bracketing
- Fix ethernet-phy node name
- add dr_mode property to OTG node
Changes in v2:
- Change model name to FriendlyElec
- Enable SD UHS modes
- Add startup delay to SDIO regulator to improve
issues reported with some cards
- Fix PMIC interrupt pin
- Add pinctrl node for ethernet-PHY
- Fix various formatting issues
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../boot/dts/rockchip/rk3328-nanopi-r2s.dts | 368 ++++++++++++++++++
2 files changed, 369 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index b87b1f773083..20055c51e150 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -5,6 +5,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-roc-cc.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3326-odroid-go2.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-nanopi-r2s.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-roc-cc.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-evb-act8846.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts
new file mode 100644
index 000000000000..b9daf89e950a
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts
@@ -0,0 +1,368 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 David Bauer <mail at david-bauer.net>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "rk3328.dtsi"
+
+/ {
+ model = "FriendlyElec NanoPi R2S";
+ compatible = "friendlyarm,nanopi-r2s", "rockchip,rk3328";
+
+ chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ gmac_clk: gmac-clock {
+ compatible = "fixed-clock";
+ clock-frequency = <125000000>;
+ clock-output-names = "gmac_clk";
+ #clock-cells = <0>;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&reset_button_pin>;
+ pinctrl-names = "default";
+
+ reset {
+ label = "reset";
+ gpios = <&gpio0 RK_PA0 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ debounce-interval = <50>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&lan_led_pin>, <&sys_led_pin>, <&wan_led_pin>;
+ pinctrl-names = "default";
+
+ lan_led: led-0 {
+ gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
+ label = "nanopi-r2s:green:lan";
+ };
+
+ sys_led: led-1 {
+ gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
+ label = "nanopi-r2s:red:sys";
+ };
+
+ wan_led: led-2 {
+ gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_HIGH>;
+ label = "nanopi-r2s:green:wan";
+ };
+ };
+
+ vcc_io_sdio: sdmmcio-regulator {
+ compatible = "regulator-gpio";
+ enable-active-high;
+ gpios = <&gpio1 RK_PD4 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&sdio_vcc_pin>;
+ pinctrl-names = "default";
+ regulator-name = "vcc_io_sdio";
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-settling-time-us = <5000>;
+ regulator-type = "voltage";
+ startup-delay-us = <2000>;
+ states = <1800000 0x1
+ 3300000 0x0>;
+ vin-supply = <&vcc_io_33>;
+ };
+
+ vcc_sd: sdmmc-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&sdmmc0m1_gpio>;
+ pinctrl-names = "default";
+ regulator-name = "vcc_sd";
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_io_33>;
+ };
+
+ vdd_5v: vdd-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_5v";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&cpu1 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&cpu2 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&cpu3 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&gmac2io {
+ assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>;
+ assigned-clock-parents = <&gmac_clk>, <&gmac_clk>;
+ clock_in_out = "input";
+ phy-handle = <&rtl8211e>;
+ phy-mode = "rgmii";
+ phy-supply = <&vcc_io_33>;
+ pinctrl-0 = <&rgmiim1_pins>;
+ pinctrl-names = "default";
+ rx_delay = <0x18>;
+ snps,aal;
+ tx_delay = <0x24>;
+ status = "okay";
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rtl8211e: ethernet-phy at 1 {
+ reg = <1>;
+ pinctrl-0 = <ð_phy_reset_pin>;
+ pinctrl-names = "default";
+ reset-assert-us = <10000>;
+ reset-deassert-us = <50000>;
+ reset-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&i2c1 {
+ status = "okay";
+
+ rk805: pmic at 18 {
+ compatible = "rockchip,rk805";
+ reg = <0x18>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+ #clock-cells = <1>;
+ clock-output-names = "xin32k", "rk805-clkout2";
+ gpio-controller;
+ #gpio-cells = <2>;
+ pinctrl-0 = <&pmic_int_l>;
+ pinctrl-names = "default";
+ rockchip,system-power-controller;
+ wakeup-source;
+
+ vcc1-supply = <&vdd_5v>;
+ vcc2-supply = <&vdd_5v>;
+ vcc3-supply = <&vdd_5v>;
+ vcc4-supply = <&vdd_5v>;
+ vcc5-supply = <&vcc_io_33>;
+ vcc6-supply = <&vdd_5v>;
+
+ regulators {
+ vdd_log: DCDC_REG1 {
+ regulator-name = "vdd_log";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1450000>;
+ regulator-ramp-delay = <12500>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vdd_arm: DCDC_REG2 {
+ regulator-name = "vdd_arm";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1450000>;
+ regulator-ramp-delay = <12500>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <950000>;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_io_33: DCDC_REG4 {
+ regulator-name = "vcc_io_33";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_18: LDO_REG1 {
+ regulator-name = "vcc_18";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc18_emmc: LDO_REG2 {
+ regulator-name = "vcc18_emmc";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdd_10: LDO_REG3 {
+ regulator-name = "vdd_10";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+ };
+ };
+};
+
+&io_domains {
+ pmuio-supply = <&vcc_io_33>;
+ vccio1-supply = <&vcc_io_33>;
+ vccio2-supply = <&vcc18_emmc>;
+ vccio3-supply = <&vcc_io_sdio>;
+ vccio4-supply = <&vcc_18>;
+ vccio5-supply = <&vcc_io_33>;
+ vccio6-supply = <&vcc_io_33>;
+ status = "okay";
+};
+
+&pinctrl {
+ button {
+ reset_button_pin: reset-button-pin {
+ rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ ethernet-phy {
+ eth_phy_reset_pin: eth-phy-reset-pin {
+ rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+
+ leds {
+ lan_led_pin: lan-led-pin {
+ rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ sys_led_pin: sys-led-pin {
+ rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ wan_led_pin: wan-led-pin {
+ rockchip,pins = <2 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ sd {
+ sdio_vcc_pin: sdio-vcc-pin {
+ rockchip,pins = <1 RK_PD4 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+};
+
+&pwm2 {
+ status = "okay";
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ disable-wp;
+ pinctrl-0 = <&sdmmc0_clk>, <&sdmmc0_cmd>, <&sdmmc0_dectn>, <&sdmmc0_bus4>;
+ pinctrl-names = "default";
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc_sd>;
+ vqmmc-supply = <&vcc_io_sdio>;
+ status = "okay";
+};
+
+&tsadc {
+ rockchip,hw-tshut-mode = <0>;
+ rockchip,hw-tshut-polarity = <0>;
+ status = "okay";
+};
+
+&u2phy {
+ status = "okay";
+};
+
+&u2phy_host {
+ status = "okay";
+};
+
+&u2phy_otg {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&usb20_otg {
+ status = "okay";
+ dr_mode = "host";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
--
2.28.0
More information about the Linux-rockchip
mailing list