[PATCH 5/8] arm64: dts: imx8mq: Correct interrupt flags in examples

[Krzysztof Kozlowski]

GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW  = 1 = IRQ_TYPE_EDGE_RISING

Correct the interrupt flags, assuming the author of the code wanted some
logical behavior behind the name "ACTIVE_xxx", this is:
  ACTIVE_LOW  => IRQ_TYPE_LEVEL_LOW

Signed-off-by: Krzysztof Kozlowski <krzk at kernel.org>

---

Not tested on HW.
---
 arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts | 5 +++--
 arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi       | 3 ++-
 arch/arm64/boot/dts/freescale/imx8mq-phanbell.dts       | 3 ++-
 arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts        | 3 ++-
 4 files changed, 9 insertions(+), 5 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
index a80e53428c2f..7f728dea32ca 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
@@ -6,6 +6,7 @@
 /dts-v1/;
 
 #include "dt-bindings/input/input.h"
+#include <dt-bindings/interrupt-controller/irq.h>
 #include "dt-bindings/pwm/pwm.h"
 #include "dt-bindings/usb/pd.h"
 #include "imx8mq.dtsi"
@@ -60,7 +61,7 @@
 			label = "WWAN_WAKE";
 			gpios = <&gpio3 8 GPIO_ACTIVE_LOW>;
 			interrupt-parent = <&gpio3>;
-			interrupts = <8 GPIO_ACTIVE_LOW>;
+			interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
 			wakeup-source;
 			linux,code = <KEY_PHONE>;
 		};
@@ -288,7 +289,7 @@
 		#clock-cells = <0>;
 		clock-output-names = "pmic_clk";
 		interrupt-parent = <&gpio1>;
-		interrupts = <3 GPIO_ACTIVE_LOW>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-names = "irq";
 		rohm,reset-snvs-powered;
 
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
index c3e290703fe8..3c389c7ffb2c 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
@@ -6,6 +6,7 @@
 /dts-v1/;
 
 #include "dt-bindings/input/input.h"
+#include <dt-bindings/interrupt-controller/irq.h>
 #include "dt-bindings/pwm/pwm.h"
 #include "dt-bindings/usb/pd.h"
 #include "imx8mq.dtsi"
@@ -639,7 +640,7 @@
 		clock-names = "osc";
 		clock-output-names = "pmic_clk";
 		interrupt-parent = <&gpio1>;
-		interrupts = <7 GPIO_ACTIVE_LOW>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-names = "irq";
 		rohm,reset-snvs-powered;
 
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-phanbell.dts b/arch/arm64/boot/dts/freescale/imx8mq-phanbell.dts
index 3f541ddf0768..05fcea2fb402 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-phanbell.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-phanbell.dts
@@ -6,6 +6,7 @@
 /dts-v1/;
 
 #include "imx8mq.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	model = "Google i.MX8MQ Phanbell";
@@ -125,7 +126,7 @@
 		clocks = <&pmic_osc>;
 		clock-output-names = "pmic_clk";
 		interrupt-parent = <&gpio1>;
-		interrupts = <3 GPIO_ACTIVE_LOW>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 
 		regulators {
 			buck1: BUCK1 {
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts b/arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts
index 59da96b7143f..84c3a143d87b 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts
@@ -9,6 +9,7 @@
 /dts-v1/;
 
 #include "imx8mq.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	model = "TechNexion PICO-PI-8M";
@@ -70,7 +71,7 @@
 		clock-names = "osc";
 		clock-output-names = "pmic_clk";
 		interrupt-parent = <&gpio1>;
-		interrupts = <3 GPIO_ACTIVE_LOW>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-names = "irq";
 
 		regulators {
-- 
2.17.1