[PATCH v2] arm64: dts: rockchip: enable HDMI sound nodes for rk3328-rock64

[Katsuhiro Suzuki]

This patch enables HDMI sound (I2S0) and Analog sound (I2S1) which
are defined in rk3328.dtsi, and replace SPDIF nodes.

We can use SPDIF pass-through with suitable ALSA settings and on
mpv or other media players.
  - Settings: https://github.com/LibreELEC/LibreELEC.tv/blob/master/projects/Rockchip/filesystem/usr/share/alsa/cards/SPDIF.conf
  - Ex.: mpv foo.ac3 --audio-spdif=ac3 --audio-device='alsa/SPDIF.pcm.iec958.0:SPDIF'

[Why use simple-audio-card for SPDIF?]

For newly adding nodes, ASoC guys recommend to use audio-graph-card.
But all other sound nodes for rk3328 have already been defined by
simple-audio-card. In this time, I chose for consistent sound nodes.

[DMA allocation problem]

After this patch is applied, UART2 will fail to allocate DMA resources
but UART driver can work fine without DMA.

This error is related to the DMAC of rk3328 (pl330 or compatible).
DMAC connected to 16 DMA sources. Each sources have ID number that is
called 'Req number' in rk3328 TRM. After this patch is applied total 7
of DMA sources will be activated as follows:

| Req number | Source | Required  |
|            |        | channels  |
|------------+--------+-----------|
|  8,  9     | SPI0   | 2ch       |
| 11, 12     | I2S0   | 2ch       |
| 14, 15     | I2S1   | 2ch       |
|     10     | SPDIF  | 1ch       |
|------------+--------+-----------|
|            | Total  | 7ch       |
|------------+--------+-----------|
|  6,  7     | UART2  | 2ch       | -> cannot get DMA channels

Due to rk3328 DMAC specification we can use max 8 channels at same
time. If SPI0/I2S0/I2S1/SPDIF will be activated by this patch,
required DMAC channels reach to 7. So the last two channels (for
UART2) cannot get DMA resources.

Virt-dma mechanism for pl0330 DMAC driver is needed to fix this
problem.

Signed-off-by: Katsuhiro Suzuki <katsuhiro at katsuster.net>
---
 .../arm64/boot/dts/rockchip/rk3328-rock64.dts | 56 ++++++++-----------
 1 file changed, 24 insertions(+), 32 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts b/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
index 86cfb5c50a94..c984662043da 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
@@ -84,34 +84,32 @@ standby_led: led-1 {
 		};
 	};
 
-	sound {
-		compatible = "audio-graph-card";
-		label = "rockchip,rk3328";
-		dais = <&i2s1_p0
-			&spdif_p0>;
+	spdif_sound: spdif-sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "SPDIF";
+
+		simple-audio-card,cpu {
+			sound-dai = <&spdif>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&spdif_dit>;
+		};
 	};
 
-	spdif-dit {
+	spdif_dit: spdif-dit {
 		compatible = "linux,spdif-dit";
 		#sound-dai-cells = <0>;
-
-		port {
-			dit_p0_0: endpoint {
-				remote-endpoint = <&spdif_p0_0>;
-			};
-		};
 	};
 };
 
+&analog_sound {
+	status = "okay";
+};
+
 &codec {
 	mute-gpios = <&grf_gpio 0 GPIO_ACTIVE_LOW>;
 	status = "okay";
-
-	port at 0 {
-		codec_p0_0: endpoint {
-			remote-endpoint = <&i2s1_p0_0>;
-		};
-	};
 };
 
 &cpu0 {
@@ -163,6 +161,10 @@ &hdmi {
 	status = "okay";
 };
 
+&hdmi_sound {
+	status = "okay";
+};
+
 &hdmiphy {
 	status = "okay";
 };
@@ -278,16 +280,12 @@ regulator-state-mem {
 	};
 };
 
-&i2s1 {
+&i2s0 {
 	status = "okay";
+};
 
-	i2s1_p0: port {
-		i2s1_p0_0: endpoint {
-			dai-format = "i2s";
-			mclk-fs = <256>;
-			remote-endpoint = <&codec_p0_0>;
-		};
-	};
+&i2s1 {
+	status = "okay";
 };
 
 &io_domains {
@@ -337,12 +335,6 @@ &sdmmc {
 &spdif {
 	pinctrl-0 = <&spdifm0_tx>;
 	status = "okay";
-
-	spdif_p0: port {
-		spdif_p0_0: endpoint {
-			remote-endpoint = <&dit_p0_0>;
-		};
-	};
 };
 
 &spi0 {
-- 
2.27.0