[PATCH V2 2/2] ARM: dts: rockchip: add dts for RK3288-Tinker board

[Heiko Stuebner]

Hi Eddie

Am Montag, 6. Februar 2017, 10:14:47 CET schrieb Eddie Cai:
> This patch add basic support for RK3288-Tinker board. We can boot in to
> rootfs with this patch.
> 
> Signed-off-by: Eddie Cai <eddie.cai at rock-chips.com>
> ---

[...]

> +&hdmi {
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	#sound-dai-cells = <0>;

why are these needed. More importantly if they are needed, they should be in 
rk3288.dtsi instead and not here.


> +	ddc-i2c-bus = <&i2c5>;
> +	status = "okay";
> +	/* Don't use vopl for HDMI */
> +	ports {
> +		hdmi_in: port {
> +			/delete-node/ endpoint at 1;
> +		};
> +	};

See comment in previous iteration, about the link to vopl being there in 
hardware and not wanting to use it for hdmi being a driver issue.
No working around driver issues in the devicetree, so leave the vop <-> hdmi 
links intact please :-)

> +};
> +
> +&i2c0 {
> +	status = "okay";
> +	clock-frequency = <400000>;
> +
> +	rk808: pmic at 1b {
> +		compatible = "rockchip,rk808";
> +		reg = <0x1b>;
> +		interrupt-parent = <&gpio0>;
> +		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pmic_int &global_pwroff &dvs_1 &dvs_2>;
> +		dvs-gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>,
> +				<&gpio0 12 GPIO_ACTIVE_HIGH>;
> +
> +		rockchip,system-power-controller;
> +		wakeup-source;
> +		#clock-cells = <1>;
> +		clock-output-names = "xin32k", "rk808-clkout2";
> +
> +		vcc1-supply = <&vcc_sys>;
> +		vcc2-supply = <&vcc_sys>;
> +		vcc3-supply = <&vcc_sys>;
> +		vcc4-supply = <&vcc_sys>;
> +		vcc6-supply = <&vcc_sys>;
> +		vcc7-supply = <&vcc_sys>;
> +		vcc8-supply = <&vcc_io>;
> +		vcc9-supply = <&vcc_io>;
> +		vcc10-supply = <&vcc_io>;
> +		vcc11-supply = <&vcc_sys>;
> +		vcc12-supply = <&vcc_io>;
> +		vddio-supply = <&vcc_io>;
> +
> +		regulators {
> +			vdd_cpu: DCDC_REG1 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <750000>;
> +				regulator-max-microvolt = <1350000>;
> +				regulator-name = "vdd_arm";
> +				regulator-ramp-delay = <6000>;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vdd_gpu: DCDC_REG2 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <850000>;
> +				regulator-max-microvolt = <1250000>;
> +				regulator-name = "vdd_gpu";
> +				regulator-ramp-delay = <6000>;
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <1000000>;
> +				};
> +			};
> +
> +			vcc_ddr: DCDC_REG3 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-name = "vcc_ddr";
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +				};
> +			};
> +
> +			vcc_io: DCDC_REG4 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-name = "vcc_io";
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <3300000>;
> +				};
> +			};
> +
> +			vcc18_ldo1: LDO_REG1 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-name = "vcc18_ldo1";
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <1800000>;
> +				};
> +			};
> +
> +			vcc33_mipi: LDO_REG2 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-name = "vcc33_mipi";
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vdd_10: LDO_REG3 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1000000>;
> +				regulator-max-microvolt = <1000000>;
> +				regulator-name = "vdd_10";
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <1000000>;
> +				};
> +			};
> +
> +			vcc18_codec: LDO_REG4 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-name = "vcc18_codec";
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <1800000>;
> +				};
> +			};
> +
> +			vccio_sd: LDO_REG5 {
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-name = "vccio_sd";
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <3300000>;
> +				};
> +			};
> +
> +			vdd10_lcd: LDO_REG6 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1000000>;
> +				regulator-max-microvolt = <1000000>;
> +				regulator-name = "vdd10_lcd";
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <1000000>;
> +				};
> +			};
> +
> +			vcc_18: LDO_REG7 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-name = "vcc_18";
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <1800000>;
> +				};
> +			};
> +
> +			vcc18_lcd: LDO_REG8 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-name = "vcc18_lcd";
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <1800000>;
> +				};
> +			};
> +
> +			vcc33_sd: SWITCH_REG1 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-name = "vcc33_sd";
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +				};
> +			};
> +
> +			vcc33_lan: SWITCH_REG2 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-name = "vcc33_lan";
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&i2c2 {
> +	status = "okay";
> +};
> +
> +&i2c5 {
> +	status = "okay";
> +};
> +
> +&i2s {
> +	#sound-dai-cells = <0>;
> +	status = "okay";
> +};
> +&vopb {
> +	status = "okay";
> +};
> +
> +&vopb_mmu {
> +	status = "okay";
> +};
> +
> +&vopl {
> +	status = "okay";
> +	/* Don't use vopl for HDMI */
> +	vopl_out: port {
> +		/delete-node/ endpoint at 0;
> +	};

same here

> +};
> +