[PATCH v3 1/2] usb: dwc2: host: Don't retry NAKed transactions right away

John Youn John.Youn at synopsys.com
Tue Dec 5 22:06:35 PST 2017


On 12/05/2017 08:18 AM, Stefan Wahren wrote:
> Hi Felipe,
> Hi John,
>
>
> Am 30.10.2017 um 18:08 schrieb Douglas Anderson:
>> On rk3288-veyron devices on Chrome OS it was found that plugging in an
>> Arduino-based USB device could cause the system to lockup, especially
>> if the CPU Frequency was at one of the slower operating points (like
>> 100 MHz / 200 MHz).
>>
>> Upon tracing, I found that the following was happening:
>> * The USB device (full speed) was connected to a high speed hub and
>>    then to the rk3288.  Thus, we were dealing with split transactions,
>>    which is all handled in software on dwc2.
>> * Userspace was initiating a BULK IN transfer
>> * When we sent the SSPLIT (to start the split transaction), we got an
>>    ACK.  Good.  Then we issued the CSPLIT.
>> * When we sent the CSPLIT, we got back a NAK.  We immediately (from
>>    the interrupt handler) started to retry and sent another SSPLIT.
>> * The device kept NAKing our CSPLIT, so we kept ping-ponging between
>>    sending a SSPLIT and a CSPLIT, each time sending from the interrupt
>>    handler.
>> * The handling of the interrupts was (because of the low CPU speed and
>>    the inefficiency of the dwc2 interrupt handler) was actually taking
>>    _longer_ than it took the other side to send the ACK/NAK.  Thus we
>>    were _always_ in the USB interrupt routine.
>> * The fact that USB interrupts were always going off was preventing
>>    other things from happening in the system.  This included preventing
>>    the system from being able to transition to a higher CPU frequency.
>>
>> As I understand it, there is no requirement to retry super quickly
>> after a NAK, we just have to retry sometime in the future.  Thus one
>> solution to the above is to just add a delay between getting a NAK and
>> retrying the transmission.  If this delay is sufficiently long to get
>> out of the interrupt routine then the rest of the system will be able
>> to make forward progress.  Even a 25 us delay would probably be
>> enough, but we'll be extra conservative and try to delay 1 ms (the
>> exact amount depends on HZ and the accuracy of the jiffy and how close
>> the current jiffy is to ticking, but could be as much as 20 ms or as
>> little as 1 ms).
>>
>> Presumably adding a delay like this could impact the USB throughput,
>> so we only add the delay with repeated NAKs.
>>
>> NOTE: Upon further testing of a pl2303 serial adapter, I found that
>> this fix may help with problems there.  Specifically I found that the
>> pl2303 serial adapters tend to respond with a NAK when they have
>> nothing to say and thus we end with this same sequence.
>>
>> Signed-off-by: Douglas Anderson <dianders at chromium.org>
>> Cc: stable at vger.kernel.org
>> Reviewed-by: Julius Werner <jwerner at chromium.org>
>> Tested-by: Stefan Wahren <stefan.wahren at i2se.com>
>> ---
>>
>> Changes in v3:
>> - Add tested-by for Stefan Wahren
>> - Sent to Felipe Balbi as candiate to land this.
>> - Add Cc for stable (it's always been broken so go as far is as easy)
>>
>> Changes in v2:
>> - Address https://urldefense.proofpoint.com/v2/url?u=http-3A__crosreview.com_737520&d=DwICaQ&c=DPL6_X_6JkXFx7AXWqB0tg&r=U3o8uKoKhWme5_V9D-eeCkB11BFwt4KvWztBgdE9ZpA&m=Y_xpJ6Ks0XAK5_bQgmeQEvgKThZtPBQJ3cejNCGfEvM&s=olyPwyYvn_072esVwYxrCduKOKKJPUgc1YHX-CNhM1s&e= feedback
>>
>
> does it need a resend?
>

You can add my acked-by:

Acked-by: John Youn <johnyoun at synopsys.com>

Regards,
John




More information about the Linux-rockchip mailing list