[PATCH v3 10/11] ARM64: dts: rockchip: Add gmac2phy node support for rk3328

[Florian Fainelli]

On 08/01/2017 11:24 PM, David Wu wrote:
> The gmac2phy controller of rk3328 is connected to internal phy
> directly inside, add the node for the internal phy support.
> 
> Signed-off-by: David Wu <david.wu at rock-chips.com>
> ---
>  arch/arm64/boot/dts/rockchip/rk3328.dtsi | 25 +++++++++++++++++++++++++
>  1 file changed, 25 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/rockchip/rk3328.dtsi b/arch/arm64/boot/dts/rockchip/rk3328.dtsi
> index 0be96ce..51c8c66 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3328.dtsi
> +++ b/arch/arm64/boot/dts/rockchip/rk3328.dtsi
> @@ -63,6 +63,8 @@
>  		i2c1 = &i2c1;
>  		i2c2 = &i2c2;
>  		i2c3 = &i2c3;
> +		ethernet0 = &gmac2io;
> +		ethernet1 = &gmac2phy;
>  	};
>  
>  	cpus {
> @@ -424,6 +426,29 @@
>  		status = "disabled";
>  	};
>  
> +	gmac2phy: eth at ff550000 {
> +		compatible = "rockchip,rk3328-gmac";
> +		reg = <0x0 0xff550000 0x0 0x10000>;
> +		rockchip,grf = <&grf>;
> +		interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
> +		interrupt-names = "macirq";
> +		clocks = <&cru SCLK_MAC2PHY_SRC>, <&cru SCLK_MAC2PHY_RXTX>,
> +			 <&cru SCLK_MAC2PHY_RXTX>, <&cru SCLK_MAC2PHY_REF>,
> +			 <&cru ACLK_MAC2PHY>, <&cru PCLK_MAC2PHY>,
> +			 <&cru SCLK_MAC2PHY_OUT>;
> +		clock-names = "stmmaceth", "mac_clk_rx",
> +			      "mac_clk_tx", "clk_mac_ref",
> +			      "aclk_mac", "pclk_mac",
> +			      "clk_macphy";
> +		resets = <&cru SRST_GMAC2PHY_A>, <&cru SRST_MACPHY>;
> +		reset-names = "stmmaceth", "mac-phy";
> +		phy-mode = "rmii";
> +		phy-is-internal;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&fephyled_rxm1 &fephyled_linkm1>;
> +		status = "disabled";

But where is the the phy-handle property that points to this internal
PHY? Even if it is internal, it should be described properly with a mdio
bus sub-node and a standard Ethernet PHY node as specified by both
Documentation/devicetree/bindings/net/mdio.txt and
Documentation/devicetree/bindings/net/phy.txt

That means we should at least see something like this (on top of what
you added already)
		phy-handle = <&phy0>;

		mdio {
			compatible = "snps,dwmac-mdio";
			#address-cells = <1>;
			#size-cells = <0>;

			phy at 0 {
				compatible = "ethernet-phy-id1234.d400", "ethernet-phy-802.3-c22";
				reg = <0>;
				phy-is-internal;
			};
		};

> +	};
> +
>  	gic: interrupt-controller at ff811000 {
>  		compatible = "arm,gic-400";
>  		#interrupt-cells = <3>;
> 


-- 
Florian