[PATCH] mfd: rk808: RK818 uses DEV_OFF to power off supplies

[chenjh]

Hi Wadim:

     It's impossible not to restart automatically, this situation is 
normal for RK818.
     Because it is hardware designed that RK818 can't power off when a 
voltage is supplies on the USB supply input pins.



Best Regards

在 2016/10/21 15:44, Wadim Egorov 写道:
> Hi Jianhong,
>
> with this patch a poweroff causes a restart on our board.
> In our design a 5V USB voltage is supplied on the USB supply input pins.
> After setting DEV_OFF bit, the RK818 restart automatically. The
> ON_SOURCE_REG (Address AEH) is 0x40 after the automatic restart which
> says that the RK818 was started by ON_PLUG_IN event.
> Is there a possibility to configure the RK818 that it will not start
> automatically in this case?
>
> Regards,
> Wadim
>
> On 17.10.2016 11:03, Jianhong Chen wrote:
>> DEV_OFF and DEV_OFF_RST functions for RK808 are designed error that
>> only DEV_OFF_RST can power off supplies. RK818 has been fixed this
>> issue, so that DEV_OFF is used to power off supplies.
>>
>> Signed-off-by: Jianhong Chen <chenjh at rock-chips.com>
>> ---
>>   drivers/mfd/rk808.c       | 23 ++++++++++++++++++++++-
>>   include/linux/mfd/rk808.h |  1 +
>>   2 files changed, 23 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/mfd/rk808.c b/drivers/mfd/rk808.c
>> index 0f8acc5..2c9acdb 100644
>> --- a/drivers/mfd/rk808.c
>> +++ b/drivers/mfd/rk808.c
>> @@ -290,6 +290,24 @@ static void rk808_device_shutdown(void)
>>   		dev_err(&rk808_i2c_client->dev, "power off error!\n");
>>   }
>>   
>> +static void rk818_device_shutdown(void)
>> +{
>> +	int ret;
>> +	struct rk808 *rk808 = i2c_get_clientdata(rk808_i2c_client);
>> +
>> +	if (!rk808) {
>> +		dev_warn(&rk808_i2c_client->dev,
>> +			 "have no rk818, so do nothing here\n");
>> +		return;
>> +	}
>> +
>> +	ret = regmap_update_bits(rk808->regmap,
>> +				 RK818_DEVCTRL_REG,
>> +				 DEV_OFF, DEV_OFF);
>> +	if (ret)
>> +		dev_err(&rk808_i2c_client->dev, "power off error!\n");
>> +}
>> +
>>   static const struct of_device_id rk808_of_match[] = {
>>   	{ .compatible = "rockchip,rk808" },
>>   	{ .compatible = "rockchip,rk818" },
>> @@ -304,6 +322,7 @@ static int rk808_probe(struct i2c_client *client,
>>   	struct rk808 *rk808;
>>   	const struct rk808_reg_data *pre_init_reg;
>>   	const struct mfd_cell *cells;
>> +	void (*pm_pwroff_fn)(void);
>>   	int nr_pre_init_regs;
>>   	int nr_cells;
>>   	int pm_off = 0;
>> @@ -331,6 +350,7 @@ static int rk808_probe(struct i2c_client *client,
>>   		nr_pre_init_regs = ARRAY_SIZE(rk808_pre_init_reg);
>>   		cells = rk808s;
>>   		nr_cells = ARRAY_SIZE(rk808s);
>> +		pm_pwroff_fn = rk808_device_shutdown;
>>   		break;
>>   	case RK818_ID:
>>   		rk808->regmap_cfg = &rk818_regmap_config;
>> @@ -339,6 +359,7 @@ static int rk808_probe(struct i2c_client *client,
>>   		nr_pre_init_regs = ARRAY_SIZE(rk818_pre_init_reg);
>>   		cells = rk818s;
>>   		nr_cells = ARRAY_SIZE(rk818s);
>> +		pm_pwroff_fn = rk818_device_shutdown;
>>   		break;
>>   	default:
>>   		dev_err(&client->dev, "Unsupported RK8XX ID %lu\n",
>> @@ -393,7 +414,7 @@ static int rk808_probe(struct i2c_client *client,
>>   				"rockchip,system-power-controller");
>>   	if (pm_off && !pm_power_off) {
>>   		rk808_i2c_client = client;
>> -		pm_power_off = rk808_device_shutdown;
>> +		pm_power_off = pm_pwroff_fn;
>>   	}
>>   
>>   	return 0;
>> diff --git a/include/linux/mfd/rk808.h b/include/linux/mfd/rk808.h
>> index 6d435a3..83701ef 100644
>> --- a/include/linux/mfd/rk808.h
>> +++ b/include/linux/mfd/rk808.h
>> @@ -290,6 +290,7 @@ enum rk818_reg {
>>   #define SWITCH2_EN	BIT(6)
>>   #define SWITCH1_EN	BIT(5)
>>   #define DEV_OFF_RST	BIT(3)
>> +#define DEV_OFF		BIT(0)
>>   
>>   #define VB_LO_ACT		BIT(4)
>>   #define VB_LO_SEL_3500MV	(7 << 0)
>
>
>