[PATCH v5 2/2] phy: rockchip-inno-usb2: add a new driver for Rockchip usb2phy

[Frank Wang]

Hi Guenter,

On 2016/6/16 21:12, Guenter Roeck wrote:
> On 06/15/2016 06:47 PM, Frank Wang wrote:
>> Hi Guenter & Heiko,
>>
>> On 2016/6/15 23:47, Guenter Roeck wrote:
>>> On Tue, Jun 14, 2016 at 6:14 PM, Frank Wang 
>>> <frank.wang at rock-chips.com> wrote:
>>>> Hi Heiko & Guenter,
>>>>
>>>>
>>>> On 2016/6/14 22:00, Heiko Stübner wrote:
>>>>> Am Dienstag, 14. Juni 2016, 06:50:31 schrieb Guenter Roeck:
>>>>>> On Tue, Jun 14, 2016 at 6:27 AM, Heiko Stübner <heiko at sntech.de> 
>>>>>> wrote:
>>>>>>> Am Montag, 13. Juni 2016, 10:10:10 schrieb Frank Wang:
>>>>>>>> The newer SoCs (rk3366, rk3399) take a different usb-phy IP block
>>>>>>>> than rk3288 and before, and most of phy-related registers are also
>>>>>>>> different from the past, so a new phy driver is required 
>>>>>>>> necessarily.
>>>>>>>>
>>>>>>>> Signed-off-by: Frank Wang <frank.wang at rock-chips.com>
>>>>>>>> ---
>>>>> [...]
>>>>>
>>>>>>>> +static int rockchip_usb2phy_init(struct phy *phy)
>>>>>>>> +{
>>>>>>>> +     struct rockchip_usb2phy_port *rport = phy_get_drvdata(phy);
>>>>>>>> +     struct rockchip_usb2phy *rphy = 
>>>>>>>> dev_get_drvdata(phy->dev.parent);
>>>>>>>> +     int ret;
>>>>>>>> +
>>>>>>>>
>>>>>>>           if (!rport->port_cfg)
>>>>>>>                            return 0;
>>>>>>>
>>>>>>> Otherwise the currently empty otg-port will cause null-pointer
>>>>>>> dereferences
>>>>>>> when it gets assigned in the devicetree already.
>>>>>> Not really, at least not here - that port should not have port_id 
>>>>>> set
>>>>>> to USB2PHY_PORT_HOST.
>>>>>>
>>>>>> Does it even make sense to instantiate the otg port ? Is it going to
>>>>>> do anything without port configuration ?
>>>>> Ok, that would be the other option - not creating the phy in the 
>>>>> driver.
>>>>
>>>> Well, I will put this conditional inside *_host_port_init(), if it 
>>>> is an
>>>> empty, the phy-device should not be created.
>>>> Something like the following:
>>>>
>>>> --- a/drivers/phy/phy-rockchip-inno-usb2.c
>>>> +++ b/drivers/phy/phy-rockchip-inno-usb2.c
>>>> @@ -483,9 +483,13 @@ static int rockchip_usb2phy_host_port_init(struct
>>>> rockchip_usb2phy *rphy,
>>>>   {
>>>>          int ret;
>>>>
>>>> -       rport->port_id = USB2PHY_PORT_HOST;
>>>>          rport->port_cfg = 
>>>> &rphy->phy_cfg->port_cfgs[USB2PHY_PORT_HOST];
>>>> +       if (!rport->port_cfg) {
>>>> +               dev_err(rphy->dev, "no host port-config provided.\n");
>>>> +               return -EINVAL;
>>>> +       }
>>> This would never be NULL. At issue is that you don't assign port_cfg
>>> if the port is _not_ a host port.
>>
>> Sorry, I made a mistake. How about something like the following:
>>
> Yes, that should work. Just keep in mind that there could always be
> a port named "something-port", so you'll always need some kind of check
> (and possibly return an error if a port with a wrong name is provided).
>
>

OK, thanks for your reminding, I am going to send out it with a new 
version later.

BR.
Frank

>
>> @@ -574,6 +579,15 @@ static int rockchip_usb2phy_probe(struct 
>> platform_device *pdev)
>>                  struct rockchip_usb2phy_port *rport = 
>> &rphy->ports[index];
>>                  struct phy *phy;
>>
>> +               /*
>> +                * This driver aim to support both otg-port and 
>> host-port,
>> +                * but unfortunately, the otg part is not ready in 
>> current,
>> +                * so this comments and below codes are interim, 
>> which should
>> +                * be removed after otg-port is supplied soon.
>> +                */
>> +               if (of_node_cmp(child_np->name, "host-port"))
>> +                       goto next_child;
>> +
>>                  phy = devm_phy_create(dev, child_np, 
>> &rockchip_usb2phy_ops);
>>                  if (IS_ERR(phy)) {
>>                          dev_err(dev, "failed to create phy\n");
>> @@ -582,17 +596,13 @@ static int rockchip_usb2phy_probe(struct 
>> platform_device *pdev)
>>                  }
>>
>>                  rport->phy = phy;
>> -
>> -               /* initialize otg/host port separately */
>> -               if (!of_node_cmp(child_np->name, "host-port")) {
>> -                       ret = rockchip_usb2phy_host_port_init(rphy, 
>> rport,
>> - child_np);
>> -                       if (ret)
>> -                               goto put_child;
>> -               }
>> -
>>                  phy_set_drvdata(rport->phy, rport);
>>
>> +               ret = rockchip_usb2phy_host_port_init(rphy, rport, 
>> child_np);
>> +               if (ret)
>> +                       goto put_child;
>> +
>> +next_child:
>>                  /* to prevent out of boundary */
>>                  if (++index >= rphy->phy_cfg->num_ports)
>>                          break;
>>
>>
>>
>