[PATCH v4 1/2] Documentation: bindings: add dt doc for Rockchip PCIe controller
Brian Norris
briannorris at chromium.org
Fri Jul 1 19:25:38 PDT 2016
Hi,
On Fri, Jul 01, 2016 at 02:01:09PM +0100, Marc Zyngier wrote:
> On 01/07/16 02:24, Shawn Lin wrote:
> > This patch adds a binding that describes the Rockchip PCIe controller
> > found on Rockchip SoCs PCIe interface.
> >
> > Signed-off-by: Shawn Lin <shawn.lin at rock-chips.com>
> >
> > ---
> >
> > Changes in v4:
> > - fix example of adding intermediate interrupt controller for pcie
> > legacy interrrupt
> >
> > Changes in v3:
> > - fix example dts code suggested by Rob and Marc
> > - remove driver's behaviour of regulator
> >
> > Changes in v2:
> > - fix lots clk/reset stuff suggested by Heiko
> > - remove msi-parent and add msi-map suggested by Marc
> > - drop phy related stuff
> > - some others minor fixes
> >
> > .../devicetree/bindings/pci/rockchip-pcie.txt | 91 ++++++++++++++++++++++
> > 1 file changed, 91 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/pci/rockchip-pcie.txt
> >
> > diff --git a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt
> > new file mode 100644
> > index 0000000..8092fc5
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt
> > @@ -0,0 +1,91 @@
> > +* Rockchip AXI PCIe Root Port Bridge DT description
> > +
> > +Required properties:
> > +- #address-cells: Address representation for root ports, set to <3>
> > +- #size-cells: Size representation for root ports, set to <2>
> > +- #interrupt-cells: specifies the number of cells needed to encode an
> > + interrupt source. The value must be 1.
I think this propoerty should be in a separate section, since it's going
under a sub-node (not the main node). Right?
> > +- compatible: Should contain "rockchip,rk3399-pcie"
> > +- reg: Two register ranges as listed in the reg-names property
> > +- reg-names: Must include the following names
> > + - "axi-base"
> > + - "apb-base"
> > +- clocks: Must contain an entry for each entry in clock-names.
> > + See ../clocks/clock-bindings.txt for details.
> > +- clock-names: Must include the following entries:
> > + - "aclk"
> > + - "aclk-perf"
> > + - "hclk"
> > + - "pm"
> > +- msi-map: Maps a Requester ID to an MSI controller and associated.
> > + See ./pci-msi.txt
> > +- phys: From PHY bindings: Phandle for the Generic PHY for PCIe.
> > +- phy-names: MUST be "pcie-phy".
> > +- interrupts: Three interrupt entries must be specified.
> > +- interrupt-names: Must include the following names
> > + - "sys"
> > + - "legacy"
> > + - "client"
> > +- resets: Must contain five entries for each entry in reset-names.
> > + See ../reset/reset.txt for details.
> > +- reset-names: Must include the following names
> > + - "core"
> > + - "mgmt"
> > + - "mgmt-sticky"
> > + - "pipe"
> > +- pinctrl-names : The pin control state names
> > +- pinctrl-0: The "default" pinctrl state
> > +- interrupt-map-mask and interrupt-map: standard PCI properties
> > +- interrupt-controller: identifies the node as an interrupt controller
Same with this property.
> > +
> > +Optional Property:
> > +- ep-gpios: contain the entry for pre-reset gpio
> > +- num-lanes: number of lanes to use
> > +- vpcie3v3-supply: The phandle to the 3.3v regulator to use for pcie.
> > +- vpcie1v8-supply: The phandle to the 1.8v regulator to use for pcie.
> > +- vpcie0v9-supply: The phandle to the 0.9v regulator to use for pcie.
e.g., you might start a new section here describing how this controller
acts as an intermediate IRQ controller, and that the
interrupt-controller-related properties should be placed under a subnode.
(Did you also need an interrupt-parent property? I'm a little fuzzy on
the details myself, actually...)
> > +
> > +Example:
> > +
> > +pcie0: pcie at f8000000 {
> > + compatible = "rockchip,rk3399-pcie";
> > + #address-cells = <3>;
> > + #size-cells = <2>;
> > + clocks = <&cru ACLK_PCIE>, <&cru ACLK_PERF_PCIE>,
> > + <&cru PCLK_PCIE>, <&cru SCLK_PCIE_PM>;
> > + clock-names = "aclk", "aclk-perf",
> > + "hclk", "pm";
> > + bus-range = <0x0 0x1>;
> > + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-names = "sys", "legacy", "client";
> > + assigned-clocks = <&cru SCLK_PCIEPHY_REF>;
> > + assigned-clock-parents = <&cru SCLK_PCIEPHY_REF100M>;
> > + assigned-clock-rates = <100000000>;
> > + ep-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
> > + ranges = <0x83000000 0x0 0xfa000000 0x0 0xfa000000 0x0 0x600000
> > + 0x81000000 0x0 0xfa600000 0x0 0xfa600000 0x0 0x100000>;
> > + num-lanes = <4>;
> > + msi-map = <0x0 &its 0x0 0x1000>;
> > + reg = < 0x0 0xf8000000 0x0 0x2000000 >, < 0x0 0xfd000000 0x0 0x1000000 >;
> > + reg-names = "axi-base", "apb-base";
> > + resets = <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>,
> > + <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE>;
> > + reset-names = "core", "mgmt", "mgmt-sticky", "pipe";
> > + phys = <&pcie_phy>;
> > + phy-names = "pcie-phy";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pcie_clkreq>;
> > + #interrupt-cells = <1>;
> > + interrupt-controller;
>
> So the pcie node itself is an interrupt controller...
>
> > + interrupt-map-mask = <0 0 0 7>;
> > + interrupt-map = <0 0 0 1 &pcie0_intc 1>,
> > + <0 0 0 2 &pcie0_intc 2>,
> > + <0 0 0 3 &pcie0_intc 3>,
> > + <0 0 0 4 &pcie0_intc 4>;
> > + pcie0_intc: interrupt-controller {
> > + interrupt-controller;
> > + #address-cells = <0>;
> > + #interrupt-cells = <1>;
> > + };
>
> But there's also another here. I just don't understand how it works.
I believe the repeat of #interrupt-cells and interrupt-controller in the
pcie@ node is a mistake. They should only be in the 'interrupt-controller'
subnode. And in case this is what you're asking about... the subnode was
present in v1 but was removed at your request:
>From Marc, in https://patchwork.kernel.org/patch/9129183/:
> > +static int rockchip_pcie_init_irq_domain(struct rockchip_pcie_port *pp)
> > +{
> > + struct device *dev = pp->dev;
> > + struct device_node *node = dev->of_node;
> > + struct device_node *pcie_intc_node = of_get_next_child(node, NULL);
>
> That's really ugly, as it depends on the layout of your DT.
>
> > +
> > + if (!pcie_intc_node) {
> > + dev_err(dev, "No PCIe Intc node found\n");
> > + return PTR_ERR(pcie_intc_node);
> > + }
> > + pp->irq_domain = irq_domain_add_linear(pcie_intc_node, 4,
> > + &intx_domain_ops, pp);
>
> Why can't you just register your host controller as the interrupt
> controller? You don't need an intermediate node for that.
But then in v3, Arnd concluded it actually *should* be used:
>From Arnd, in https://patchwork.kernel.org/patch/9179763/:
> On Thursday, June 16, 2016 4:01:12 PM CEST Wenrui Li wrote:
> > 在 2016/6/16 15:00, Arnd Bergmann 写道:
> > > On Thursday, June 16, 2016 9:50:21 AM CEST Shawn Lin wrote:
> > >
> > >> + reset-names = "core", "mgmt", "mgmt-sticky", "pipe";
> > >> + phys = <&pcie_phy>;
> > >> + phy-names = "pcie-phy";
> > >> + pinctrl-names = "default";
> > >> + pinctrl-0 = <&pcie_clkreq>;
> > >> + #interrupt-cells = <1>;
> > >> + interrupt-controller;
> > >> + interrupt-map-mask = <0 0 0 7>;
> > >> + interrupt-map = <0 0 0 1 &pcie0 1>,
> > >> + <0 0 0 2 &pcie0 2>,
> > >> + <0 0 0 3 &pcie0 3>,
> > >> + <0 0 0 4 &pcie0 4>;
> > >> +};
> > >>
> > >
> > > One thing that came up in the review of the new Marvell PCIe driver is that it's
> > > most likely invalid for a device node to have both "interrupt-controller"
> > > and "interrupt-map" properties. I originally thought this was a nice way to
> > > handle embedded irqchips within the PCIe host, but it only really works
> > > by coincidence with the current kernel, and only as long as the hwirq number
> > > of the irqchip matches the integer representation of the irq line in the root
> > > bridge (which it does in the example above).
> > >
> > > For that driver we concluded that it would be less of a hack to have the
> > > irqchip as a child node of the PCIe host after all (just not with
> > > device_type="pci" of course), and that makes the translation work as
> > > expected.
> > >
> > > Arnd
> > >
> >
> > Original driver have an irqchip as child node. But Marc suggested don't
> > need an intermediate node here.
> > Now the conclusion is to retain the child node?
>
> That is at least my view of the situation, sorry for the mixed messages
> you have been getting. Marc, Rob, do you agree with my finding?
Rob and others agreed with the subnode. So, I hope you don't disagree in
principle, and are only confused by the duplicate properties?
Regards,
Brian
More information about the Linux-rockchip
mailing list