[PATCH v2 2/2] phy: add a driver for the Rockchip SoC internal eMMC PHY
Shawn Lin
shawn.lin at rock-chips.com
Sun Jan 24 23:49:47 PST 2016
Hello Kishon,
Any changce to apply this patch? :)
On 2016/1/5 9:08, Shawn Lin wrote:
> This patch to add a generic PHY driver for ROCKCHIP eMMC PHY.
> Access the PHY via registers provided by GRF (general register
> files) module.
>
> Signed-off-by: Shawn Lin <shawn.lin at rock-chips.com>
>
> ---
>
> Changes in v2:
> - remove phy from rockchip_emmc_phy
> - remove state from rockchip_emmc_phy
> - remove on/off from init/exit
>
> drivers/phy/Kconfig | 7 ++
> drivers/phy/Makefile | 1 +
> drivers/phy/phy-rockchip-emmc.c | 241 ++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 249 insertions(+)
> create mode 100644 drivers/phy/phy-rockchip-emmc.c
>
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index 03cb3ea..47d16e3 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -320,6 +320,13 @@ config PHY_ROCKCHIP_USB
> help
> Enable this to support the Rockchip USB 2.0 PHY.
>
> +config PHY_ROCKCHIP_EMMC
> + tristate "Rockchip EMMC PHY Driver"
> + depends on ARCH_ROCKCHIP && OF
> + select GENERIC_PHY
> + help
> + Enable this to support the Rockchip EMMC PHY.
> +
> config PHY_ST_SPEAR1310_MIPHY
> tristate "ST SPEAR1310-MIPHY driver"
> select GENERIC_PHY
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index 075db1a..ed8f175 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -35,6 +35,7 @@ phy-exynos-usb2-$(CONFIG_PHY_S5PV210_USB2) += phy-s5pv210-usb2.o
> obj-$(CONFIG_PHY_EXYNOS5_USBDRD) += phy-exynos5-usbdrd.o
> obj-$(CONFIG_PHY_QCOM_APQ8064_SATA) += phy-qcom-apq8064-sata.o
> obj-$(CONFIG_PHY_ROCKCHIP_USB) += phy-rockchip-usb.o
> +obj-$(CONFIG_PHY_ROCKCHIP_EMMC) += phy-rockchip-emmc.o
> obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA) += phy-qcom-ipq806x-sata.o
> obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY) += phy-spear1310-miphy.o
> obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY) += phy-spear1340-miphy.o
> diff --git a/drivers/phy/phy-rockchip-emmc.c b/drivers/phy/phy-rockchip-emmc.c
> new file mode 100644
> index 0000000..6a157c2
> --- /dev/null
> +++ b/drivers/phy/phy-rockchip-emmc.c
> @@ -0,0 +1,241 @@
> +/*
> + * Rockchip emmc PHY driver
> + *
> + * Copyright (C) 2015 Shawn Lin <shawn.lin at rock-chips.com>
> + * Copyright (C) 2015 ROCKCHIP, Inc.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/delay.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +
> +/*
> + * The higher 16-bit of this register is used for write protection
> + * only if BIT(x + 16) set to 1 the BIT(x) can be written.
> + */
> +#define HIWORD_UPDATE(val, mask, shift) \
> + ((val) << (shift) | (mask) << ((shift) + 16))
> +
> +/* Register definition */
> +#define GRF_EMMCPHY_CON0 0x0
> +#define GRF_EMMCPHY_CON1 0x4
> +#define GRF_EMMCPHY_CON2 0x8
> +#define GRF_EMMCPHY_CON3 0xc
> +#define GRF_EMMCPHY_CON4 0x10
> +#define GRF_EMMCPHY_CON5 0x14
> +#define GRF_EMMCPHY_CON6 0x18
> +#define GRF_EMMCPHY_STATUS 0x20
> +
> +#define PHYCTRL_PDB_MASK 0x1
> +#define PHYCTRL_PDB_SHIFT 0x0
> +#define PHYCTRL_PDB_PWR_ON 0x1
> +#define PHYCTRL_PDB_PWR_OFF 0x0
> +#define PHYCTRL_ENDLL_MASK 0x1
> +#define PHYCTRL_ENDLL_SHIFT 0x1
> +#define PHYCTRL_ENDLL_ENABLE 0x1
> +#define PHYCTRL_ENDLL_DISABLE 0x0
> +#define PHYCTRL_CALDONE_MASK 0x1
> +#define PHYCTRL_CALDONE_SHIFT 0x6
> +#define PHYCTRL_CALDONE_DONE 0x1
> +#define PHYCTRL_CALDONE_GOING 0x0
> +#define PHYCTRL_DLLRDY_MASK 0x1
> +#define PHYCTRL_DLLRDY_SHIFT 0x5
> +#define PHYCTRL_DLLRDY_DONE 0x1
> +#define PHYCTRL_DLLRDY_GOING 0x0
> +
> +struct rockchip_emmc_phy {
> + unsigned int reg_offset;
> + struct regmap *reg_base;
> +};
> +
> +static int rockchip_emmc_phy_power(struct rockchip_emmc_phy *rk_phy,
> + bool on_off)
> +{
> + unsigned int caldone;
> + unsigned int dllrdy;
> +
> + /*
> + * Keep phyctrl_pdb and phyctrl_endll low to allow
> + * initialization of CALIO state M/C DFFs
> + */
> + regmap_write(rk_phy->reg_base,
> + rk_phy->reg_offset + GRF_EMMCPHY_CON6,
> + HIWORD_UPDATE(PHYCTRL_PDB_PWR_OFF,
> + PHYCTRL_PDB_MASK,
> + PHYCTRL_PDB_SHIFT));
> + regmap_write(rk_phy->reg_base,
> + rk_phy->reg_offset + GRF_EMMCPHY_CON6,
> + HIWORD_UPDATE(PHYCTRL_ENDLL_DISABLE,
> + PHYCTRL_ENDLL_MASK,
> + PHYCTRL_ENDLL_SHIFT));
> +
> + /* Already finish power_off above */
> + if (on_off == PHYCTRL_PDB_PWR_OFF)
> + return 0;
> +
> + /*
> + * According to the user manual, calpad calibration
> + * cycle takes more than 2us without the minimal recommended
> + * value, so we may need a little margin here
> + */
> + udelay(3);
> + regmap_write(rk_phy->reg_base,
> + rk_phy->reg_offset + GRF_EMMCPHY_CON6,
> + HIWORD_UPDATE(PHYCTRL_PDB_PWR_ON,
> + PHYCTRL_PDB_MASK,
> + PHYCTRL_PDB_SHIFT));
> +
> + /*
> + * According to the user manual, it asks driver to
> + * wait 5us for calpad busy trimming
> + */
> + udelay(5);
> + regmap_read(rk_phy->reg_base,
> + rk_phy->reg_offset + GRF_EMMCPHY_STATUS,
> + &caldone);
> + caldone = (caldone >> PHYCTRL_CALDONE_SHIFT) & PHYCTRL_CALDONE_MASK;
> + if (caldone != PHYCTRL_CALDONE_DONE) {
> + pr_err("rockchip_emmc_phy_power: caldone timeout.\n");
> + return -ETIMEDOUT;
> + }
> +
> + /*
> + * Enable analog DLL circuits, and we need extra 10.2us
> + * for dll to be ready for work.
> + */
> + regmap_write(rk_phy->reg_base,
> + rk_phy->reg_offset + GRF_EMMCPHY_CON6,
> + HIWORD_UPDATE(PHYCTRL_ENDLL_ENABLE,
> + PHYCTRL_ENDLL_MASK,
> + PHYCTRL_ENDLL_SHIFT));
> + udelay(11);
> + regmap_read(rk_phy->reg_base,
> + rk_phy->reg_offset + GRF_EMMCPHY_STATUS,
> + &dllrdy);
> + dllrdy = (dllrdy >> PHYCTRL_DLLRDY_SHIFT) & PHYCTRL_DLLRDY_MASK;
> + if (dllrdy != PHYCTRL_DLLRDY_DONE) {
> + pr_err("rockchip_emmc_phy_power: dllrdy timeout.\n");
> + return -ETIMEDOUT;
> + }
> +
> + return 0;
> +}
> +
> +static int rockchip_emmc_phy_power_off(struct phy *phy)
> +{
> + struct rockchip_emmc_phy *rk_phy = phy_get_drvdata(phy);
> + int ret = 0;
> +
> + /* Power down emmc phy analog blocks */
> + ret = rockchip_emmc_phy_power(rk_phy, PHYCTRL_PDB_PWR_OFF);
> + if (ret)
> + return ret;
> +
> + return 0;
> +}
> +
> +static int rockchip_emmc_phy_power_on(struct phy *phy)
> +{
> + struct rockchip_emmc_phy *rk_phy = phy_get_drvdata(phy);
> + int ret = 0;
> +
> + /* Power up emmc phy analog blocks */
> + ret = rockchip_emmc_phy_power(rk_phy, PHYCTRL_PDB_PWR_ON);
> + if (ret)
> + return ret;
> +
> + return 0;
> +}
> +
> +static int rockchip_emmc_phy_init(struct phy *phy)
> +{
> + return 0;
> +}
> +
> +static int rockchip_emmc_phy_exit(struct phy *phy)
> +{
> + return 0;
> +}
> +
> +static const struct phy_ops ops = {
> + .init = rockchip_emmc_phy_init,
> + .exit = rockchip_emmc_phy_exit,
> + .power_on = rockchip_emmc_phy_power_on,
> + .power_off = rockchip_emmc_phy_power_off,
> + .owner = THIS_MODULE,
> +};
> +
> +static int rockchip_emmc_phy_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct rockchip_emmc_phy *rk_phy;
> + struct phy *generic_phy;
> + struct phy_provider *phy_provider;
> + struct regmap *grf;
> + unsigned int reg_offset;
> +
> + grf = syscon_regmap_lookup_by_phandle(dev->of_node, "rockchip,grf");
> + if (IS_ERR(grf)) {
> + dev_err(dev, "Missing rockchip,grf property\n");
> + return PTR_ERR(grf);
> + }
> +
> + rk_phy = devm_kzalloc(dev, sizeof(*rk_phy), GFP_KERNEL);
> + if (!rk_phy)
> + return -ENOMEM;
> +
> + if (of_property_read_u32(dev->of_node, "reg", ®_offset)) {
> + dev_err(dev, "missing reg property in node %s\n",
> + dev->of_node->name);
> + return -EINVAL;
> + }
> +
> + rk_phy->reg_offset = reg_offset;
> + rk_phy->reg_base = grf;
> +
> + generic_phy = devm_phy_create(dev, dev->of_node, &ops);
> + if (IS_ERR(generic_phy)) {
> + dev_err(dev, "failed to create PHY\n");
> + return PTR_ERR(generic_phy);
> + }
> +
> + phy_set_drvdata(generic_phy, rk_phy);
> + phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> +
> + return PTR_ERR_OR_ZERO(phy_provider);
> +}
> +
> +static const struct of_device_id rockchip_emmc_phy_dt_ids[] = {
> + { .compatible = "rockchip,rk3399-emmc-phy" },
> + {}
> +};
> +
> +MODULE_DEVICE_TABLE(of, rockchip_emmc_phy_dt_ids);
> +
> +static struct platform_driver rockchip_emmc_driver = {
> + .probe = rockchip_emmc_phy_probe,
> + .driver = {
> + .name = "rockchip-emmc-phy",
> + .of_match_table = rockchip_emmc_phy_dt_ids,
> + },
> +};
> +
> +module_platform_driver(rockchip_emmc_driver);
> +
> +MODULE_AUTHOR("Shawn Lin <shawn.lin at rock-chips.com>");
> +MODULE_DESCRIPTION("Rockchip EMMC PHY driver");
> +MODULE_LICENSE("GPL v2");
>
--
Best Regards
Shawn Lin
More information about the Linux-rockchip
mailing list