[PATCH 10/12] drm: bridge/dw_hdmi: fix phy enable/disable handling
Russell King - ARM Linux
linux at arm.linux.org.uk
Wed Oct 7 12:17:31 PDT 2015
On Wed, Oct 07, 2015 at 06:40:11PM +0800, Yakir Yang wrote:
>
>
> On 10/07/2015 05:48 PM, Russell King - ARM Linux wrote:
> >On Wed, Oct 07, 2015 at 12:05:37PM +0800, Yakir Yang wrote:
> >>
> >>On 08/09/2015 12:04 AM, Russell King wrote:
> >>>The dw_hdmi enable/disable handling is particularly weak in several
> >>>regards:
> >>>* The hotplug interrupt could call hdmi_poweron() or hdmi_poweroff()
> >>> while DRM is setting a mode, which could race with a mode being set.
> >>>* Hotplug will always re-enable the phy whenever it detects an active
> >>> hotplug signal, even if DRM has disabled the output.
> >>>
> >>>Resolve all of these by introducing a mutex to prevent races, and a
> >>>state-tracking bool so we know whether DRM wishes the output to be
> >>>enabled. We choose to use our own mutex rather than ->struct_mutex
> >>>so that we can still process interrupts in a timely fashion.
> >>>
> >>>Signed-off-by: Russell King <rmk+kernel at arm.linux.org.uk>
> >>>---
> >>> drivers/gpu/drm/bridge/dw_hdmi.c | 29 ++++++++++++++++++++++-------
> >>> 1 file changed, 22 insertions(+), 7 deletions(-)
> >>>
> >>>diff --git a/drivers/gpu/drm/bridge/dw_hdmi.c b/drivers/gpu/drm/bridge/dw_hdmi.c
> >>>index 7b8a4e942a71..0ee188930d26 100644
> >>>--- a/drivers/gpu/drm/bridge/dw_hdmi.c
> >>>+++ b/drivers/gpu/drm/bridge/dw_hdmi.c
> >>>@@ -125,6 +125,9 @@ struct dw_hdmi {
> >>> bool sink_is_hdmi;
> >>> bool sink_has_audio;
> >>>+ struct mutex mutex; /* for state below and previous_mode */
> >>>+ bool disabled; /* DRM has disabled our bridge */
> >>>+
> >>> spinlock_t audio_lock;
> >>> struct mutex audio_mutex;
> >>> unsigned int sample_rate;
> >>>@@ -1389,8 +1392,12 @@ static void dw_hdmi_bridge_mode_set(struct drm_bridge *bridge,
> >>> {
> >>> struct dw_hdmi *hdmi = bridge->driver_private;
> >>>+ mutex_lock(&hdmi->mutex);
> >>>+
> >>> /* Store the display mode for plugin/DKMS poweron events */
> >>> memcpy(&hdmi->previous_mode, mode, sizeof(hdmi->previous_mode));
> >>>+
> >>>+ mutex_unlock(&hdmi->mutex);
> >>> }
> >>> static bool dw_hdmi_bridge_mode_fixup(struct drm_bridge *bridge,
> >>>@@ -1404,14 +1411,20 @@ static void dw_hdmi_bridge_disable(struct drm_bridge *bridge)
> >>> {
> >>> struct dw_hdmi *hdmi = bridge->driver_private;
> >>>+ mutex_lock(&hdmi->mutex);
> >>>+ hdmi->disabled = true;
> >>> dw_hdmi_poweroff(hdmi);
> >>>+ mutex_unlock(&hdmi->mutex);
> >>> }
> >>> static void dw_hdmi_bridge_enable(struct drm_bridge *bridge)
> >>> {
> >>> struct dw_hdmi *hdmi = bridge->driver_private;
> >>>+ mutex_lock(&hdmi->mutex);
> >>> dw_hdmi_poweron(hdmi);
> >>>+ hdmi->disabled = false;
> >>>+ mutex_unlock(&hdmi->mutex);
> >>> }
> >>> static void dw_hdmi_bridge_nop(struct drm_bridge *bridge)
> >>>@@ -1534,20 +1547,20 @@ static irqreturn_t dw_hdmi_irq(int irq, void *dev_id)
> >>> phy_int_pol = hdmi_readb(hdmi, HDMI_PHY_POL0);
> >>> if (intr_stat & HDMI_IH_PHY_STAT0_HPD) {
> >>>+ hdmi_modb(hdmi, ~phy_int_pol, HDMI_PHY_HPD, HDMI_PHY_POL0);
> >>>+ mutex_lock(&hdmi->mutex);
> >>> if (phy_int_pol & HDMI_PHY_HPD) {
> >>> dev_dbg(hdmi->dev, "EVENT=plugin\n");
> >>>- hdmi_modb(hdmi, 0, HDMI_PHY_HPD, HDMI_PHY_POL0);
> >>>-
> >>>- dw_hdmi_poweron(hdmi);
> >>>+ if (!hdmi->disabled)
> >>>+ dw_hdmi_poweron(hdmi);
> >>> } else {
> >>> dev_dbg(hdmi->dev, "EVENT=plugout\n");
> >>>- hdmi_modb(hdmi, HDMI_PHY_HPD, HDMI_PHY_HPD,
> >>>- HDMI_PHY_POL0);
> >>>-
> >>>- dw_hdmi_poweroff(hdmi);
> >>>+ if (!hdmi->disabled)
> >>>+ dw_hdmi_poweroff(hdmi);
> >>Just like my reply on 08/12, I thought this could be removed, so
> >>poweron/poweroff would only be called with bridge->enable/
> >>bridge->disable, them maybe no need mutex here.
> >The bridge enable/disable methods do not get called on hotplug changes.
> >
> >[ 1.363011] dwhdmi-imx 120000.hdmi: Detected HDMI controller 0x13:0xa:0xa0:0xc1
> >[ 1.371341] dwhdmi-imx 120000.hdmi: dw_hdmi_irq(I:RX----,HPD P:RX3210,HPD S:RX----,HPD)
> >[ 1.381345] imx-drm display-subsystem: bound 120000.hdmi (ops dw_hdmi_imx_ops)
> >[ 1.448691] dwhdmi-imx 120000.hdmi: dw_hdmi_bridge_disable()
> >[ 1.450963] dwhdmi-imx 120000.hdmi: dw_hdmi_bridge_enable()
> >
> >and then unplugging and re-plugging the HDMI cable:
> >
> >[ 68.307505] dwhdmi-imx 120000.hdmi: dw_hdmi_irq(I:RX----,HPD P:RX3210,--- S:RX----,---)
> >[ 73.813970] dwhdmi-imx 120000.hdmi: dw_hdmi_irq(I:RX----,HPD P:RX3210,HPD S:RX----,HPD)
> >
> >As you can see, during the period of disconnection for five seconds,
> >dw_hdmi_bridge_disable() was not called.
> >
> >So, without the code above, we'd be needlessly wasting power with the
> >bridge enabled, trying to drive a disconnected display.
>
> Strangely, I do see bridge enable/disable in my side, past the log and
> dump_stack bellow.
>
> And I guess your HDMI maybe not really hot pluged, could you confirm that
> the "status" of HDMI display card have been changed between "connected"
> and "disconnected".
It does.
> Do see bridge_disable when I unpluging the HDMI cable
> [ 16.358717] dwhdmi-rockchip ff980000.hdmi: EVENT=plugout
> [ 20.613221] [<c010e030>] (unwind_backtrace) from [<c010a4e0>]
> (show_stack+0x20/0x24)
> [ 20.631561] [<c010a4e0>] (show_stack) from [<c0896828>]
> (dump_stack+0x70/0x8c)
> [ 20.649337] [<c0896828>] (dump_stack) from [<c0414038>]
> (dw_hdmi_bridge_disable+0x1c/0x88)
> [ 20.668178] [<c0414038>] (dw_hdmi_bridge_disable) from [<c03e3888>]
> (drm_encoder_disable+0x34/0x78)
> [ 20.687857] [<c03e3888>] (drm_encoder_disable) from [<c03e3b1c>]
> (__drm_helper_disable_unused_functions+0x68/0xe4)
> [ 20.708975] [<c03e3b1c>] (__drm_helper_disable_unused_functions) from
> [<c03e4320>] (drm_crtc_helper_set_config+0x128/0x85c)
> [ 20.731180] [<c03e4320>] (drm_crtc_helper_set_config) from [<c03f5e3c>]
> (drm_mode_set_config_internal+0x58/0xdc)
> [ 20.752507] [<c03f5e3c>] (drm_mode_set_config_internal) from [<c0405ed0>]
> (commit_crtc_state+0x124/0x1ec)
> [ 20.773342] [<c0405ed0>] (commit_crtc_state) from [<c04055d4>]
> (atomic_commit.isra.3+0x5c/0xc8)
> [ 20.793397] [<c04055d4>] (atomic_commit.isra.3) from [<c040565c>]
> (drm_atomic_commit+0x1c/0x20)
> [ 20.813467] [<c040565c>] (drm_atomic_commit) from [<c03fa480>]
> (drm_mode_setcrtc+0x324/0x3e4)
> [ 20.833379] [<c03fa480>] (drm_mode_setcrtc) from [<c03eb320>]
> (drm_ioctl+0x304/0x478)
> [ 20.852557] [<c03eb320>] (drm_ioctl) from [<c021f024>]
> (do_vfs_ioctl+0x494/0x5a8)
> [ 20.871377] [<c021f024>] (do_vfs_ioctl) from [<c021f194>]
> (SyS_ioctl+0x5c/0x84)
> [ 20.890038] [<c021f194>] (SyS_ioctl) from [<c010646c>]
> (__sys_trace_return+0x0/0x14)
Your userspace is issuing an ioctl to disable the output. I guess you
have other active outputs besides HDMI.
--
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.
More information about the Linux-rockchip
mailing list