[PATCH v4 1/2] regulator: st-pwm: get voltage and duty table from dts
Chris Zhong
zyw at rock-chips.com
Sun Sep 21 19:52:59 PDT 2014
Get voltage & duty table from device tree might be better, other platforms can also use this
driver without any modify.
Signed-off-by: Chris Zhong <zyw at rock-chips.com>
Reviewed-by: Doug Anderson <dianders at chromium.org>
---
Changes in v4:
Adviced by Doug Anderson
- improve kconfig
- add const for desc structure
Changes in v3:
Adviced by Doug Anderson
- Make Kconfig & Makefile alphabetical
- remove pwm_reg_period from pwm_regulator_data
- modify the calculation in pwm_regulator_set_voltage_sel
- add length validity check
Changes in v2:
Adviced by Lee Jones
- rename the file
- remove all the prefix st_
- add depend on PWM in Kconfig
drivers/regulator/Kconfig | 13 +--
drivers/regulator/Makefile | 2 +-
drivers/regulator/pwm-regulator.c | 197 +++++++++++++++++++++++++++++++++++++
drivers/regulator/st-pwm.c | 190 -----------------------------------
4 files changed, 205 insertions(+), 197 deletions(-)
create mode 100644 drivers/regulator/pwm-regulator.c
delete mode 100644 drivers/regulator/st-pwm.c
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index fb32bab..b927cab 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -449,6 +449,13 @@ config REGULATOR_PFUZE100
Say y here to support the regulators found on the Freescale
PFUZE100/PFUZE200 PMIC.
+config REGULATOR_PWM
+ tristate "PWM voltage regulator"
+ depends on PWM
+ help
+ This driver supports PWM controlled voltage regulators. PWM
+ duty cycle can increase or decrease the voltage.
+
config REGULATOR_RC5T583
tristate "RICOH RC5T583 Power regulators"
depends on MFD_RC5T583
@@ -493,12 +500,6 @@ config REGULATOR_S5M8767
via I2C bus. S5M8767A have 9 Bucks and 28 LDOs output and
supports DVS mode with 8bits of output voltage control.
-config REGULATOR_ST_PWM
- tristate "STMicroelectronics PWM voltage regulator"
- depends on ARCH_STI
- help
- This driver supports ST's PWM controlled voltage regulators.
-
config REGULATOR_TI_ABB
tristate "TI Adaptive Body Bias on-chip LDO"
depends on ARCH_OMAP
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 236fdbb..f3cf5a5 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -57,6 +57,7 @@ obj-$(CONFIG_REGULATOR_MC13892) += mc13892-regulator.o
obj-$(CONFIG_REGULATOR_MC13XXX_CORE) += mc13xxx-regulator-core.o
obj-$(CONFIG_REGULATOR_PALMAS) += palmas-regulator.o
obj-$(CONFIG_REGULATOR_PFUZE100) += pfuze100-regulator.o
+obj-$(CONFIG_REGULATOR_PWM) += pwm-regulator.o
obj-$(CONFIG_REGULATOR_TPS51632) += tps51632-regulator.o
obj-$(CONFIG_REGULATOR_PBIAS) += pbias-regulator.o
obj-$(CONFIG_REGULATOR_PCAP) += pcap-regulator.o
@@ -66,7 +67,6 @@ obj-$(CONFIG_REGULATOR_RK808) += rk808-regulator.o
obj-$(CONFIG_REGULATOR_S2MPA01) += s2mpa01.o
obj-$(CONFIG_REGULATOR_S2MPS11) += s2mps11.o
obj-$(CONFIG_REGULATOR_S5M8767) += s5m8767.o
-obj-$(CONFIG_REGULATOR_ST_PWM) += st-pwm.o
obj-$(CONFIG_REGULATOR_STW481X_VMMC) += stw481x-vmmc.o
obj-$(CONFIG_REGULATOR_TI_ABB) += ti-abb-regulator.o
obj-$(CONFIG_REGULATOR_TPS6105X) += tps6105x-regulator.o
diff --git a/drivers/regulator/pwm-regulator.c b/drivers/regulator/pwm-regulator.c
new file mode 100644
index 0000000..d3f55ea
--- /dev/null
+++ b/drivers/regulator/pwm-regulator.c
@@ -0,0 +1,197 @@
+/*
+ * Regulator driver for PWM Regulators
+ *
+ * Copyright (C) 2014 - STMicroelectronics Inc.
+ *
+ * Author: Lee Jones <lee.jones at linaro.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/err.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/of_regulator.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pwm.h>
+
+struct pwm_regulator_data {
+ struct regulator_desc desc;
+ struct pwm_voltages *duty_cycle_table;
+ struct pwm_device *pwm;
+ bool enabled;
+ int state;
+};
+
+struct pwm_voltages {
+ unsigned int uV;
+ unsigned int dutycycle;
+};
+
+static int pwm_regulator_get_voltage_sel(struct regulator_dev *dev)
+{
+ struct pwm_regulator_data *drvdata = rdev_get_drvdata(dev);
+
+ return drvdata->state;
+}
+
+static int pwm_regulator_set_voltage_sel(struct regulator_dev *dev,
+ unsigned selector)
+{
+ struct pwm_regulator_data *drvdata = rdev_get_drvdata(dev);
+ unsigned int pwm_reg_period;
+ int dutycycle;
+ int ret;
+
+ pwm_reg_period = pwm_get_period(drvdata->pwm);
+
+ dutycycle = (pwm_reg_period *
+ drvdata->duty_cycle_table[selector].dutycycle) / 100;
+
+ ret = pwm_config(drvdata->pwm, dutycycle, pwm_reg_period);
+ if (ret) {
+ dev_err(&dev->dev, "Failed to configure PWM\n");
+ return ret;
+ }
+
+ drvdata->state = selector;
+
+ if (!drvdata->enabled) {
+ ret = pwm_enable(drvdata->pwm);
+ if (ret) {
+ dev_err(&dev->dev, "Failed to enable PWM\n");
+ return ret;
+ }
+ drvdata->enabled = true;
+ }
+
+ return 0;
+}
+
+static int pwm_regulator_list_voltage(struct regulator_dev *dev,
+ unsigned selector)
+{
+ struct pwm_regulator_data *drvdata = rdev_get_drvdata(dev);
+
+ if (selector >= drvdata->desc.n_voltages)
+ return -EINVAL;
+
+ return drvdata->duty_cycle_table[selector].uV;
+}
+
+static struct regulator_ops pwm_regulator_voltage_ops = {
+ .set_voltage_sel = pwm_regulator_set_voltage_sel,
+ .get_voltage_sel = pwm_regulator_get_voltage_sel,
+ .list_voltage = pwm_regulator_list_voltage,
+ .map_voltage = regulator_map_voltage_iterate,
+};
+
+static const struct regulator_desc pwm_regulator_desc = {
+ .name = "pwm-regulator",
+ .ops = &pwm_regulator_voltage_ops,
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+ .supply_name = "pwm",
+};
+
+static int pwm_regulator_probe(struct platform_device *pdev)
+{
+ struct pwm_regulator_data *drvdata;
+ struct property *prop;
+ struct regulator_dev *regulator;
+ struct regulator_config config = { };
+ struct device_node *np = pdev->dev.of_node;
+ int length, ret;
+
+ if (!np) {
+ dev_err(&pdev->dev, "Device Tree node missing\n");
+ return -EINVAL;
+ }
+
+ drvdata = devm_kzalloc(&pdev->dev, sizeof(*drvdata), GFP_KERNEL);
+ if (!drvdata)
+ return -ENOMEM;
+
+ memcpy(&drvdata->desc, &pwm_regulator_desc, sizeof(pwm_regulator_desc));
+
+ /* determine the number of voltage-table */
+ prop = of_find_property(np, "voltage-table", &length);
+ if (!prop) {
+ dev_err(&pdev->dev, "No voltage-table\n");
+ return -EINVAL;
+ }
+
+ if ((length < sizeof(*drvdata->duty_cycle_table)) ||
+ (length % sizeof(*drvdata->duty_cycle_table))) {
+ dev_err(&pdev->dev, "voltage-table length(%d) is invalid\n",
+ length);
+ return -EINVAL;
+ }
+
+ drvdata->desc.n_voltages = length / sizeof(*drvdata->duty_cycle_table);
+
+ drvdata->duty_cycle_table = devm_kzalloc(&pdev->dev,
+ length, GFP_KERNEL);
+ if (!drvdata->duty_cycle_table)
+ return -ENOMEM;
+
+ /* read voltage table from DT property */
+ ret = of_property_read_u32_array(np, "voltage-table",
+ (u32 *)drvdata->duty_cycle_table,
+ length / sizeof(u32));
+ if (ret < 0) {
+ dev_err(&pdev->dev, "read voltage-table failed\n");
+ return ret;
+ }
+
+ config.init_data = of_get_regulator_init_data(&pdev->dev, np);
+ if (!config.init_data)
+ return -ENOMEM;
+
+ config.of_node = np;
+ config.dev = &pdev->dev;
+ config.driver_data = drvdata;
+
+ drvdata->pwm = devm_pwm_get(&pdev->dev, NULL);
+ if (IS_ERR(drvdata->pwm)) {
+ dev_err(&pdev->dev, "Failed to get PWM\n");
+ return PTR_ERR(drvdata->pwm);
+ }
+
+ regulator = devm_regulator_register(&pdev->dev,
+ &drvdata->desc, &config);
+ if (IS_ERR(regulator)) {
+ dev_err(&pdev->dev, "Failed to register regulator %s\n",
+ drvdata->desc.name);
+ return PTR_ERR(regulator);
+ }
+
+ return 0;
+}
+
+static const struct of_device_id pwm_of_match[] = {
+ { .compatible = "pwm-regulator" },
+ { },
+};
+MODULE_DEVICE_TABLE(of, pwm_of_match);
+
+static struct platform_driver pwm_regulator_driver = {
+ .driver = {
+ .name = "pwm-regulator",
+ .owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(pwm_of_match),
+ },
+ .probe = pwm_regulator_probe,
+};
+
+module_platform_driver(pwm_regulator_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Lee Jones <lee.jones at linaro.org>");
+MODULE_DESCRIPTION("PWM Regulator Driver");
+MODULE_ALIAS("platform:pwm-regulator");
diff --git a/drivers/regulator/st-pwm.c b/drivers/regulator/st-pwm.c
deleted file mode 100644
index 5ea78df..0000000
--- a/drivers/regulator/st-pwm.c
+++ /dev/null
@@ -1,190 +0,0 @@
-/*
- * Regulator driver for ST's PWM Regulators
- *
- * Copyright (C) 2014 - STMicroelectronics Inc.
- *
- * Author: Lee Jones <lee.jones at linaro.org>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/err.h>
-#include <linux/regulator/driver.h>
-#include <linux/regulator/machine.h>
-#include <linux/regulator/of_regulator.h>
-#include <linux/of.h>
-#include <linux/of_device.h>
-#include <linux/pwm.h>
-
-#define ST_PWM_REG_PERIOD 8448
-
-struct st_pwm_regulator_pdata {
- const struct regulator_desc *desc;
- struct st_pwm_voltages *duty_cycle_table;
-};
-
-struct st_pwm_regulator_data {
- const struct st_pwm_regulator_pdata *pdata;
- struct pwm_device *pwm;
- bool enabled;
- int state;
-};
-
-struct st_pwm_voltages {
- unsigned int uV;
- unsigned int dutycycle;
-};
-
-static int st_pwm_regulator_get_voltage_sel(struct regulator_dev *dev)
-{
- struct st_pwm_regulator_data *drvdata = rdev_get_drvdata(dev);
-
- return drvdata->state;
-}
-
-static int st_pwm_regulator_set_voltage_sel(struct regulator_dev *dev,
- unsigned selector)
-{
- struct st_pwm_regulator_data *drvdata = rdev_get_drvdata(dev);
- int dutycycle;
- int ret;
-
- dutycycle = (ST_PWM_REG_PERIOD / 100) *
- drvdata->pdata->duty_cycle_table[selector].dutycycle;
-
- ret = pwm_config(drvdata->pwm, dutycycle, ST_PWM_REG_PERIOD);
- if (ret) {
- dev_err(&dev->dev, "Failed to configure PWM\n");
- return ret;
- }
-
- drvdata->state = selector;
-
- if (!drvdata->enabled) {
- ret = pwm_enable(drvdata->pwm);
- if (ret) {
- dev_err(&dev->dev, "Failed to enable PWM\n");
- return ret;
- }
- drvdata->enabled = true;
- }
-
- return 0;
-}
-
-static int st_pwm_regulator_list_voltage(struct regulator_dev *dev,
- unsigned selector)
-{
- struct st_pwm_regulator_data *drvdata = rdev_get_drvdata(dev);
-
- if (selector >= dev->desc->n_voltages)
- return -EINVAL;
-
- return drvdata->pdata->duty_cycle_table[selector].uV;
-}
-
-static struct regulator_ops st_pwm_regulator_voltage_ops = {
- .set_voltage_sel = st_pwm_regulator_set_voltage_sel,
- .get_voltage_sel = st_pwm_regulator_get_voltage_sel,
- .list_voltage = st_pwm_regulator_list_voltage,
- .map_voltage = regulator_map_voltage_iterate,
-};
-
-static struct st_pwm_voltages b2105_duty_cycle_table[] = {
- { .uV = 1114000, .dutycycle = 0, },
- { .uV = 1095000, .dutycycle = 10, },
- { .uV = 1076000, .dutycycle = 20, },
- { .uV = 1056000, .dutycycle = 30, },
- { .uV = 1036000, .dutycycle = 40, },
- { .uV = 1016000, .dutycycle = 50, },
- /* WARNING: Values above 50% duty-cycle cause boot failures. */
-};
-
-static const struct regulator_desc b2105_desc = {
- .name = "b2105-pwm-regulator",
- .ops = &st_pwm_regulator_voltage_ops,
- .type = REGULATOR_VOLTAGE,
- .owner = THIS_MODULE,
- .n_voltages = ARRAY_SIZE(b2105_duty_cycle_table),
- .supply_name = "pwm",
-};
-
-static const struct st_pwm_regulator_pdata b2105_info = {
- .desc = &b2105_desc,
- .duty_cycle_table = b2105_duty_cycle_table,
-};
-
-static const struct of_device_id st_pwm_of_match[] = {
- { .compatible = "st,b2105-pwm-regulator", .data = &b2105_info, },
- { },
-};
-MODULE_DEVICE_TABLE(of, st_pwm_of_match);
-
-static int st_pwm_regulator_probe(struct platform_device *pdev)
-{
- struct st_pwm_regulator_data *drvdata;
- struct regulator_dev *regulator;
- struct regulator_config config = { };
- struct device_node *np = pdev->dev.of_node;
- const struct of_device_id *of_match;
-
- if (!np) {
- dev_err(&pdev->dev, "Device Tree node missing\n");
- return -EINVAL;
- }
-
- drvdata = devm_kzalloc(&pdev->dev, sizeof(*drvdata), GFP_KERNEL);
- if (!drvdata)
- return -ENOMEM;
-
- of_match = of_match_device(st_pwm_of_match, &pdev->dev);
- if (!of_match) {
- dev_err(&pdev->dev, "failed to match of device\n");
- return -ENODEV;
- }
- drvdata->pdata = of_match->data;
-
- config.init_data = of_get_regulator_init_data(&pdev->dev, np);
- if (!config.init_data)
- return -ENOMEM;
-
- config.of_node = np;
- config.dev = &pdev->dev;
- config.driver_data = drvdata;
-
- drvdata->pwm = devm_pwm_get(&pdev->dev, NULL);
- if (IS_ERR(drvdata->pwm)) {
- dev_err(&pdev->dev, "Failed to get PWM\n");
- return PTR_ERR(drvdata->pwm);
- }
-
- regulator = devm_regulator_register(&pdev->dev,
- drvdata->pdata->desc, &config);
- if (IS_ERR(regulator)) {
- dev_err(&pdev->dev, "Failed to register regulator %s\n",
- drvdata->pdata->desc->name);
- return PTR_ERR(regulator);
- }
-
- return 0;
-}
-
-static struct platform_driver st_pwm_regulator_driver = {
- .driver = {
- .name = "st-pwm-regulator",
- .owner = THIS_MODULE,
- .of_match_table = of_match_ptr(st_pwm_of_match),
- },
- .probe = st_pwm_regulator_probe,
-};
-
-module_platform_driver(st_pwm_regulator_driver);
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Lee Jones <lee.jones at linaro.org>");
-MODULE_DESCRIPTION("ST PWM Regulator Driver");
-MODULE_ALIAS("platform:st_pwm-regulator");
--
1.7.9.5
More information about the Linux-rockchip
mailing list