[PATCH 2/4] dt-bindings: Document EMAC Rockchip

[Heiko Stübner]

Am Mittwoch, 3. September 2014, 10:27:14 schrieb Romain Perier:
> This adds the necessary binding documentation for the EMAC Rockchip platform
> driver found in RK3066 and RK3188 SoCs.
> 
> Signed-off-by: Romain Perier <romain.perier at gmail.com>
> ---
>  .../devicetree/bindings/net/emac_rockchip.txt      | 53
> ++++++++++++++++++++++ 1 file changed, 53 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/net/emac_rockchip.txt
> 
> diff --git a/Documentation/devicetree/bindings/net/emac_rockchip.txt
> b/Documentation/devicetree/bindings/net/emac_rockchip.txt new file mode
> 100644
> index 0000000..d3242e4
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/emac_rockchip.txt
> @@ -0,0 +1,53 @@
> +* ARC EMAC 10/100 Ethernet platform driver for Rockchip Rk3066/RK3188 SoCs
> +
> +Required properties:
> +- compatible: Should be "rockchip,rk3066-emac" or "rockchip,rk3188-emac"
> +  according to the target SoC.
> +- reg: Address and length of the register set for the device
> +- interrupts: Should contain the EMAC interrupts
> +- pinctrl-names: pin control state name ("default").
> +- pinctrl-0: pin control group list of phandle. It must contain
> +  pin control groups for communication with the phy and for the mii bus.

pinctrl is normally not supposed to be part of the binding doc, as it is a 
property of the board and not the controller IP itself


> +- rockchip,grf: phandle to the syscon grf used to control speed and mode
> +  for emac.
> +- phy: see ethernet.txt file in the same directory.
> +- phy-mode: see ethernet.txt file in the same directory.
> +
> +Optional properties:
> +- phy-supply: phandle to a regulator if the PHY needs one
> +
> +Clock handling:
> +- The host clock is needed to calculate and set polling period of EMAC.
> +  It must be provided by the clock "hclk".
> +- The reference clock is needed to get/set data from phy at the right
> frequency,
> +  according to its "phy-mode". It must be provided by the clock
> "macref".

I think a more often used scheme is something like

- clocks: Must contain an entry for each entry in clock-names.
- clock-names: Shall be "hclk" for the host clock needed to calculate and
			set polling period of EMAC and "macref" for the reference
			clock needed to transfer data to and from the phy.


> +
> +Child nodes of the driver are the individual PHY devices connected to the
> +MDIO bus. They must have a "reg" property given the PHY address on the MDIO
> bus. +
> +Examples:
> +
> +ethernet at 10204000 {
> +	compatible = "rockchip,rk3188-emac";
> +	reg = <0xc0fc2000 0x3c>;
> +	interrupts = <6>;
> +	mac-address = [ 00 11 22 33 44 55 ];
> +
> +	clocks = <&cru HCLK_EMAC>, <&cru SCLK_MAC>;
> +	clock-names = "hclk", "macref";
> +
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&phy_int>;
> +
> +	rockchip,grf = <&grf>;
> +
> +	phy = <&phy0>;
> +	phy-mode = "rmii";
> +	phy-supply = <&vcc_rmii>;
> +
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	phy0: ethernet-phy at 0 {
> +	      reg = <1>;
> +	};
> +};