[PATCH 3/3] riscv: dts: spacemit: k1: Add Banana Pi BPI-CM6 IO board

Junhui Liu junhui.liu at pigmoral.tech
Fri May 22 03:01:35 PDT 2026 

The Banana Pi BPI-CM6 IO board combines the BPI-CM6 compute module with
an IO carrier board. The core module integrates the SpacemiT K1 SoC,
PMIC, DDR, eMMC, the eth0 PHY, and wireless connectivity. The companion
IO carrier board extends it by providing the eth1 PHY and exposing
standard interfaces, including dual Gigabit Ethernet, MicroSD, two USB-A
ports, a USB Type-C port, two PCIe M.2 slots, and a serial console.

The board also has two I2C EEPROMs. One is on the core module, which
stores factory manufacturing data and is marked read-only. The other is
on the carrier board, which is shipped unprogrammed and left writable
for evaluation purposes.

Add initial support for UART console, eMMC, SD card, I2C, EEPROMs,
PCIe, USB, and dual Ethernet interfaces.

Link: https://docs.banana-pi.org/en/BPI-CM6/BananaPi_BPI-CM6
Signed-off-by: Junhui Liu <junhui.liu at pigmoral.tech>
---
 arch/riscv/boot/dts/spacemit/Makefile              |   1 +
 .../riscv/boot/dts/spacemit/k1-bananapi-cm6-io.dts | 215 +++++++++++++++++++
 arch/riscv/boot/dts/spacemit/k1-bananapi-cm6.dtsi  | 227 +++++++++++++++++++++
 3 files changed, 443 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/Makefile b/arch/riscv/boot/dts/spacemit/Makefile
index acb993c452ba..dd6125dc2012 100644
--- a/arch/riscv/boot/dts/spacemit/Makefile
+++ b/arch/riscv/boot/dts/spacemit/Makefile
@@ -1,4 +1,5 @@
 # SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_SPACEMIT) += k1-bananapi-cm6-io.dtb
 dtb-$(CONFIG_ARCH_SPACEMIT) += k1-bananapi-f3.dtb
 dtb-$(CONFIG_ARCH_SPACEMIT) += k1-milkv-jupiter.dtb
 dtb-$(CONFIG_ARCH_SPACEMIT) += k1-musepi-pro.dtb
diff --git a/arch/riscv/boot/dts/spacemit/k1-bananapi-cm6-io.dts b/arch/riscv/boot/dts/spacemit/k1-bananapi-cm6-io.dts
new file mode 100644
index 000000000000..b2767f44e8d6
--- /dev/null
+++ b/arch/riscv/boot/dts/spacemit/k1-bananapi-cm6-io.dts
@@ -0,0 +1,215 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2026 Junhui Liu <junhui.liu at pigmoral.tech>
+ */
+
+#include "k1-bananapi-cm6.dtsi"
+
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Banana Pi BPI-CM6 IO Board";
+	compatible = "bananapi,bpi-cm6-io", "bananapi,bpi-cm6", "spacemit,k1";
+
+	aliases {
+		ethernet0 = &eth0;
+		ethernet1 = &eth1;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led0 {
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio K1_GPIO(96) GPIO_ACTIVE_LOW>;
+		};
+
+		led1 {
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&gpio K1_GPIO(97) GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	vdd_sys_12v: regulator-vdd-sys-12v {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_SYS";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_vdd_5v0: regulator-vdd-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_5V0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		regulator-always-on;
+		vin-supply = <&vdd_sys_12v>;
+	};
+
+	pcie_vcc_3v3: regulator-pcie-vcc-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "NGFF_KEYM_VDD";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+		vin-supply = <&vdd_sys_12v>;
+	};
+
+	usb_vbus_5v: regulator-usb-vbus-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "VBUS_A_B";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio K1_GPIO(124) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&reg_vdd_5v0>;
+	};
+
+	reg_vdd_3v3: regulator-vdd-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+		vin-supply = <&vdd_sys_12v>;
+	};
+
+	sd_vcc_3v3: regulator-sd-vcc-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3.3VS_CARD";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio K1_GPIO(127) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&reg_vdd_3v3>;
+	};
+};
+
+&combo_phy {
+	status = "okay";
+};
+
+&eth0 {
+	status = "okay";
+};
+
+&eth1 {
+	nvmem-cells = <&mac_address 1>;
+	nvmem-cell-names = "mac-address";
+	phy-handle = <&rgmii1>;
+	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac1_cfg>;
+	rx-internal-delay-ps = <0>;
+	tx-internal-delay-ps = <250>;
+	status = "okay";
+
+	mdio-bus {
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+
+		reset-gpios = <&gpio K1_GPIO(46) GPIO_ACTIVE_LOW>;
+		reset-delay-us = <10000>;
+		reset-post-delay-us = <100000>;
+
+		rgmii1: phy at 1 {
+			reg = <0x1>;
+		};
+	};
+};
+
+&i2c2 {
+	eeprom at 54 {
+		compatible = "atmel,24c08";
+		reg = <0x54>;
+		vcc-supply = <&buck3_1v8>;
+		pagesize = <16>;
+		size = <1024>;
+	};
+};
+
+&pcie1_phy {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie1_3_cfg>;
+	status = "okay";
+};
+
+&pcie1_port {
+	phys = <&pcie1_phy>;
+	vpcie3v3-supply = <&pcie_vcc_3v3>;
+};
+
+&pcie1 {
+	vpcie3v3-supply = <&pcie_vcc_3v3>;
+	status = "okay";
+};
+
+&pcie2_phy {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie2_4_cfg>;
+	status = "okay";
+};
+
+&pcie2_port {
+	phys = <&pcie2_phy>;
+	vpcie3v3-supply = <&pcie_vcc_3v3>;
+};
+
+&pcie2 {
+	vpcie3v3-supply = <&pcie_vcc_3v3>;
+	status = "okay";
+};
+
+&qspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&qspi_cfg>;
+	status = "okay";
+};
+
+&sdhci0 {
+	pinctrl-names = "default", "uhs";
+	pinctrl-0 = <&mmc1_cfg>;
+	pinctrl-1 = <&mmc1_uhs_cfg>;
+	bus-width = <4>;
+	cd-gpios = <&gpio K1_GPIO(80) (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	no-mmc;
+	no-sdio;
+	disable-wp;
+	cap-sd-highspeed;
+	vmmc-supply = <&sd_vcc_3v3>;
+	vqmmc-supply = <&aldo1>;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_2_cfg>;
+	status = "okay";
+};
+
+&usbphy2 {
+	status = "okay";
+};
+
+&usb_dwc3 {
+	dr_mode = "host";
+	vbus-supply = <&usb_vbus_5v>;
+	status = "okay";
+};
+
+&vddin_sys_5v {
+	vin-supply = <&reg_vdd_5v0>;
+};
diff --git a/arch/riscv/boot/dts/spacemit/k1-bananapi-cm6.dtsi b/arch/riscv/boot/dts/spacemit/k1-bananapi-cm6.dtsi
new file mode 100644
index 000000000000..9b91128edb34
--- /dev/null
+++ b/arch/riscv/boot/dts/spacemit/k1-bananapi-cm6.dtsi
@@ -0,0 +1,227 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2026 Junhui Liu <junhui.liu at pigmoral.tech>
+ */
+
+#include "k1.dtsi"
+#include "k1-pinctrl.dtsi"
+
+/ {
+	model = "Banana Pi BPI-CM6 Module";
+	compatible = "bananapi,bpi-cm6", "spacemit,k1";
+
+	aliases {
+		i2c2 = &i2c2;
+		i2c8 = &i2c8;
+	};
+
+	vddin_sys_5v: regulator-vddin-sys-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIN_SYS";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_vcc_4v: regulator-vcc-4v {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC4V0_SYS";
+		regulator-min-microvolt = <4000000>;
+		regulator-max-microvolt = <4000000>;
+		regulator-boot-on;
+		regulator-always-on;
+		vin-supply = <&vddin_sys_5v>;
+	};
+};
+
+&emmc {
+	bus-width = <8>;
+	mmc-hs400-1_8v;
+	mmc-hs400-enhanced-strobe;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
+&eth0 {
+	nvmem-cells = <&mac_address 0>;
+	nvmem-cell-names = "mac-address";
+	phy-handle = <&rgmii0>;
+	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac0_cfg>;
+	rx-internal-delay-ps = <0>;
+	tx-internal-delay-ps = <0>;
+
+	mdio-bus {
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+
+		reset-gpios = <&gpio K1_GPIO(45) GPIO_ACTIVE_LOW>;
+		reset-delay-us = <10000>;
+		reset-post-delay-us = <100000>;
+
+		rgmii0: phy at 1 {
+			reg = <0x1>;
+		};
+	};
+};
+
+&pdma {
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_0_cfg>;
+	status = "okay";
+
+	eeprom at 50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		vcc-supply = <&buck3_1v8>;
+		pagesize = <16>;
+		read-only;
+		size = <256>;
+
+		nvmem-layout {
+			compatible = "onie,tlv-layout";
+
+			mac_address: mac-address {
+				#nvmem-cell-cells = <1>;
+			};
+
+			num-macs {
+			};
+
+			serial-number {
+			};
+		};
+	};
+};
+
+&i2c8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c8_cfg>;
+	status = "okay";
+
+	pmic at 41 {
+		compatible = "spacemit,p1";
+		reg = <0x41>;
+		interrupts = <64>;
+		vin1-supply = <&reg_vcc_4v>;
+		vin2-supply = <&reg_vcc_4v>;
+		vin3-supply = <&reg_vcc_4v>;
+		vin4-supply = <&reg_vcc_4v>;
+		vin5-supply = <&reg_vcc_4v>;
+		vin6-supply = <&reg_vcc_4v>;
+		aldoin-supply = <&reg_vcc_4v>;
+		dldoin1-supply = <&buck5>;
+		dldoin2-supply = <&buck5>;
+
+		regulators {
+			buck1 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3450000>;
+				regulator-ramp-delay = <5000>;
+				regulator-always-on;
+			};
+
+			buck2 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3450000>;
+				regulator-ramp-delay = <5000>;
+				regulator-always-on;
+			};
+
+			buck3_1v8: buck3 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-ramp-delay = <5000>;
+				regulator-always-on;
+			};
+
+			buck4 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-ramp-delay = <5000>;
+				regulator-always-on;
+			};
+
+			buck5: buck5 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3450000>;
+				regulator-ramp-delay = <5000>;
+				regulator-always-on;
+			};
+
+			buck6 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3450000>;
+				regulator-ramp-delay = <5000>;
+				regulator-always-on;
+			};
+
+			aldo1: aldo1 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-boot-on;
+			};
+
+			aldo2 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+			};
+
+			aldo3 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+			};
+
+			aldo4 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+			};
+
+			dldo1 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-boot-on;
+			};
+
+			dldo2 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+			};
+
+			dldo3 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+			};
+
+			dldo4 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-always-on;
+			};
+
+			dldo5 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+			};
+
+			dldo6 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-always-on;
+			};
+
+			dldo7 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+			};
+		};
+	};
+};

-- 
2.54.0

More information about the linux-riscv mailing list