[PATCH 3/3] riscv: dts: spacemit: add QSPI support for K3 Pico-ITX

[Zhengyu He]

Describe the K3 QSPI controller and the pin configuration needed by
boards.

Enable the bus on Pico-ITX because the board wires QSPI to NOR flash
powered from the board 1.8 V QSPI rail.

Signed-off-by: Zhengyu He <hezhy472013 at gmail.com>
Signed-off-by: Cody Kang <cody.kang.hk at outlook.com>
---
 arch/riscv/boot/dts/spacemit/k3-pico-itx.dts | 58 ++++++++++++++++++++++++++++
 arch/riscv/boot/dts/spacemit/k3-pinctrl.dtsi | 21 ++++++++++
 arch/riscv/boot/dts/spacemit/k3.dtsi         | 16 ++++++++
 3 files changed, 95 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
index 4486dc1fe114..61cbf924830b 100644
--- a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
+++ b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
@@ -192,6 +192,64 @@ phy0: phy at 1 {
 	};
 };
 
+&pinctrl {
+	qspi-cfg {
+		qspi-pins {
+			power-source = <1800>;
+		};
+
+		qspi-cs0-pins {
+			power-source = <1800>;
+		};
+	};
+};
+
+&qspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&qspi_cfg>;
+	status = "okay";
+
+	flash at 0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <26500000>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <4>;
+		vcc-supply = <&aldo2>; /* PMIC_VCC1V8_QSPI */
+		m25p,fast-read;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			bootinfo at 0 {
+				reg = <0x0 0x20000>;
+			};
+
+			fsbl at 20000 {
+				reg = <0x20000 0x80000>;
+			};
+
+			env at a0000 {
+				reg = <0xa0000 0x10000>;
+			};
+
+			esos at b0000 {
+				reg = <0xb0000 0x100000>;
+			};
+
+			opensbi at 1b0000 {
+				reg = <0x1b0000 0x60000>;
+			};
+
+			uboot at 210000 {
+				reg = <0x210000 0x5f0000>;
+			};
+		};
+	};
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_0_cfg>;
diff --git a/arch/riscv/boot/dts/spacemit/k3-pinctrl.dtsi b/arch/riscv/boot/dts/spacemit/k3-pinctrl.dtsi
index 23899d3f308a..5d9763791180 100644
--- a/arch/riscv/boot/dts/spacemit/k3-pinctrl.dtsi
+++ b/arch/riscv/boot/dts/spacemit/k3-pinctrl.dtsi
@@ -56,6 +56,27 @@ i2c8-pins {
 		};
 	};
 
+	/omit-if-no-ref/
+	qspi_cfg: qspi-cfg {
+		qspi-pins {
+			pinmux = <K3_PADCONF(138, 0)>,	/* qspi dat0 */
+				 <K3_PADCONF(139, 0)>,	/* qspi dat1 */
+				 <K3_PADCONF(140, 0)>,	/* qspi dat2 */
+				 <K3_PADCONF(141, 0)>,	/* qspi dat3 */
+				 <K3_PADCONF(144, 0)>;	/* qspi clk */
+
+			bias-disable;
+			drive-strength = <25>;
+		};
+
+		qspi-cs0-pins {
+			pinmux = <K3_PADCONF(142, 0)>;	/* qspi cs0 */
+
+			bias-disable;
+			drive-strength = <25>;
+		};
+	};
+
 	/omit-if-no-ref/
 	uart0_0_cfg: uart0-0-cfg {
 		uart0-0-pins {
diff --git a/arch/riscv/boot/dts/spacemit/k3.dtsi b/arch/riscv/boot/dts/spacemit/k3.dtsi
index 815debd16409..800efc2929a4 100644
--- a/arch/riscv/boot/dts/spacemit/k3.dtsi
+++ b/arch/riscv/boot/dts/spacemit/k3.dtsi
@@ -836,6 +836,22 @@ pll: clock-controller at d4090000 {
 			#clock-cells = <1>;
 		};
 
+		qspi: spi at d420c000 {
+			compatible = "spacemit,k3-qspi";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0xd420c000 0x0 0x1000>,
+			      <0x0 0xb8000000 0x0 0xc00000>;
+			reg-names = "QuadSPI", "QuadSPI-memory";
+			clocks = <&syscon_apmu CLK_APMU_QSPI_BUS>,
+				 <&syscon_apmu CLK_APMU_QSPI>;
+			clock-names = "qspi_en", "qspi";
+			resets = <&syscon_apmu RESET_APMU_QSPI>,
+				 <&syscon_apmu RESET_APMU_QSPI_BUS>;
+			interrupts = <117 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
 		syscon_apmu: system-controller at d4282800 {
 			compatible = "spacemit,k3-syscon-apmu";
 			reg = <0x0 0xd4282800 0x0 0x400>;

-- 
2.53.0