[PATCH v2 08/22] dt-bindings: pinctrl: Add starfive,jhb100-sys1-pinctrl
Changhuang Liang
changhuang.liang at starfivetech.com
Thu May 14 04:12:04 PDT 2026
Add pinctrl bindings for StarFive JHB100 SoC System-1(sys1) pinctrl
controller.
Signed-off-by: Changhuang Liang <changhuang.liang at starfivetech.com>
---
.../pinctrl/starfive,jhb100-sys1-pinctrl.yaml | 175 ++++++++++++++++++
.../pinctrl/starfive,jhb100-pinctrl.h | 10 +
2 files changed, 185 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys1-pinctrl.yaml
diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys1-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys1-pinctrl.yaml
new file mode 100644
index 000000000000..f9a7998d11cb
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/starfive,jhb100-sys1-pinctrl.yaml
@@ -0,0 +1,175 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/starfive,jhb100-sys1-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JHB100 System-1 Pin Controller
+
+description: |
+ Pinctrl bindings for JHB100 RISC-V SoC from StarFive Technology Ltd.
+
+ The JHB100 SoC has 13 pinctrl domains - sys0, sys0h, sys1, sys2, per0, per1,
+ per2, per2pok, per3, adc0, adc1, emmc, and vga.
+ This document provides an overview of the "sys1" pinctrl domain.
+
+ The "sys1" domain has a pin controller which provides
+ - function selection for GPIO pads.
+ - GPIO pad configuration.
+ - GPIO interrupt handling.
+
+ In the SYS1 Pin Controller, there are 8 multi-function GPIO_PADs. Each of
+ them can be multiplexed to different hardware blocks through function
+ selection. Each iopad has a maximum of up to 4 functions - 0, 1, 2, and 3.
+ Function 0 is the default function which is generally the GPIO function
+ (or occasionally, it can be a peripheral signal).
+ Function 1, 2, and 3 are the alternate functions or peripheral signals that
+ can be routed to the iopad. The function selection can be carried out by
+ writing the function number to the iopad function select register.
+
+ Each iopad is configurable with parameters such as input-enable, internal
+ pull-up/pull-down bias, drive strength, schmitt trigger, slew rate, input
+ debounce nanoseconds, power source and drive type (open-drain or push-pull).
+
+maintainers:
+ - Alex Soo <yuklin.soo at starfivetech.com>
+
+properties:
+ compatible:
+ items:
+ - const: starfive,jhb100-sys1-pinctrl
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ '#interrupt-cells':
+ const: 3
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ const: 3
+
+ gpio-ranges: true
+
+ gpio-line-names: true
+
+patternProperties:
+ '-grp$':
+ type: object
+ additionalProperties: false
+ patternProperties:
+ '-pins$':
+ type: object
+ description: |
+ A pinctrl node should contain at least one subnode representing the
+ pinctrl groups available in the domain. Each subnode will list the
+ pins it needs, and how they should be configured, with regard to
+ function selection, bias, input enable/disable, input schmitt
+ trigger enable/disable, slew-rate, input debounce nanoseconds,
+ drive-open-drain, drive-push-pull, power-source and drive-strength.
+ allOf:
+ - $ref: /schemas/pinctrl/pincfg-node.yaml
+ - $ref: /schemas/pinctrl/pinmux-node.yaml
+ unevaluatedProperties: false
+
+ properties:
+ pins:
+ description:
+ The list of IOs that properties in the pincfg node apply to.
+
+ function:
+ description:
+ A string containing the name of the function to mux for these
+ pins.
+ enum: [ espi, espi_reset, gpio, host0_port80, host1_port80 ]
+
+ bias-disable: true
+
+ bias-pull-down:
+ type: boolean
+
+ bias-pull-up:
+ oneOf:
+ - type: boolean
+ - enum: [ 600, 900, 1200, 2000 ]
+ description: Pull up RSEL type resistance values (in ohms)
+ description:
+ For normal pull up type there is no need to specify a resistance
+ value, hence this can be specified as a boolean property.
+ For RSEL pull up type a resistance value (in ohms) can be added.
+
+ drive-open-drain: true
+
+ drive-push-pull: true
+
+ drive-strength:
+ enum: [ 2, 4, 8, 12 ]
+
+ drive-strength-microamp:
+ enum: [ 2000, 4000, 8000, 12000 ]
+
+ input-debounce-nanoseconds:
+ minimum: 0
+ maximum: 4294967295
+
+ input-disable: true
+
+ input-enable: true
+
+ input-schmitt-enable: true
+
+ input-schmitt-disable: true
+
+ power-source:
+ enum: [ 0, 1, 2 ]
+
+ slew-rate:
+ enum: [ 0, 1 ]
+ default: 0
+ description: |
+ 0: slow (half frequency)
+ 1: fast
+
+required:
+ - compatible
+ - reg
+ - resets
+ - interrupts
+ - interrupt-controller
+ - '#interrupt-cells'
+ - gpio-controller
+ - '#gpio-cells'
+ - gpio-ranges
+
+additionalProperties: false
+
+examples:
+ - |
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ pinctrl_sys1: pinctrl at 13081000 {
+ compatible = "starfive,jhb100-sys1-pinctrl";
+ reg = <0x0 0x13081000 0x0 0x1000>;
+ resets = <&sys1crg 2>;
+ interrupts = <58>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ gpio-ranges = <&pinctrl_sys1 0 0 0 8>;
+ };
+ };
diff --git a/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h b/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
index 38d5a94e92e3..30704a5a3418 100644
--- a/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
+++ b/include/dt-bindings/pinctrl/starfive,jhb100-pinctrl.h
@@ -28,4 +28,14 @@
#define PADNUM_SYS0H_GPIO_A14 10
#define PADNUM_SYS0H_GPIO_A15 11
+/* sys1 pad numbers */
+#define PADNUM_SYS1_GPIO_A16 0
+#define PADNUM_SYS1_GPIO_A17 1
+#define PADNUM_SYS1_GPIO_A18 2
+#define PADNUM_SYS1_GPIO_A19 3
+#define PADNUM_SYS1_GPIO_A20 4
+#define PADNUM_SYS1_GPIO_A21 5
+#define PADNUM_SYS1_GPIO_A22 6
+#define PADNUM_SYS1_GPIO_A23 7
+
#endif
--
2.25.1
More information about the linux-riscv
mailing list