[PATCH v9 8/8] riscv: dts: spacemit: k1-musepi-pro: add SD card support with UHS modes

[Yixun Lan]

Hi Iker, Trevor,

On 10:54 Mon 11 May     , Iker Pedrosa wrote:
> From: Trevor Gamblin <tgamblin at baylibre.com>
> 
> Update the Muse Pi Pro devicetree with SD card support to match what
> was done for the OrangePi RV2 in [1]. More precisely:
> 
> - Enable sdhci0 controller with 4-bit bus width
> - Configure card detect GPIO with inversion
> - Connect vmmc-supply to buck4 for 3.3V card power
> - Connect vqmmc-supply to aldo1 for 1.8V/3.3V I/O switching
> - Add dual pinctrl states for voltage-dependent pin configuration
> - Support UHS-I SDR25, SDR50, and SDR104 modes
> 
> [1] https://lore.kernel.org/linux-riscv/20260316-orangepi-sd-card-uhs-v3-0-aefd3b7832df@gmail.com/T/#
> 
> Signed-off-by: Trevor Gamblin <tgamblin at baylibre.com>
> Signed-off-by: Iker Pedrosa <ikerpedrosam at gmail.com>
> ---
>  arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts | 66 ++++++++++++++++++++++++++
>  1 file changed, 66 insertions(+)
> 
> diff --git a/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts b/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
> index 29e333b670cf..774a4640f065 100644
> --- a/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
> +++ b/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
> @@ -18,6 +18,24 @@ aliases {
>  		ethernet0 = &eth0;
>  		serial0 = &uart0;
>  	};
Add one blank line here, but see comment below..
> +	reg_dc_in: dc-in-5v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "dc_in_5v";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
reg_dc_in is not used, drop it, for the reason, see recent discussion of
this thread here[1][2], especially refer to Krzysztof's original comment
https://lore.kernel.org/all/6530526f-59ca-4753-a068-46c62a1a1fed@kernel.org/ [1]
https://lore.kernel.org/all/20260511065338-GKA3624147@kernel.org/  [2]

> +
> +	reg_vcc_4v: vcc-4v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc_4v";
> +		regulator-min-microvolt = <4000000>;
> +		regulator-max-microvolt = <4000000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
> +
>  
>  	chosen {
>  		stdout-path = "serial0";
> @@ -77,3 +95,51 @@ &uart0 {
>  	pinctrl-names = "default";
>  	status = "okay";
>  };
> +
> +&i2c8 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c8_cfg>;
> +	status = "okay";
> +
> +	pmic at 41 {
> +		compatible = "spacemit,p1";
> +		reg = <0x41>;
> +		interrupts = <64>;
..
> +		vin-supply = <&reg_vcc_4v>;
This should be adjusted, please check schematics as I haven't done it
myself, for reason behind please refer to this patch (which was merged
in v7.1)

http://lore.kernel.org/r/20260206-spacemit-p1-v4-1-8f695d93811e@riscstar.com

> +
> +		regulators {
> +			buck4: buck4 {
> +				regulator-min-microvolt = <500000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-ramp-delay = <5000>;
> +				regulator-always-on;
> +			};
> +
> +			aldo1: aldo1 {
> +				regulator-min-microvolt = <500000>;
> +				regulator-max-microvolt = <3400000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +		};
> +	};
> +};
> +
> +&sdhci0 {
> +	pinctrl-names = "default", "uhs";
> +	pinctrl-0 = <&mmc1_cfg>;
> +	pinctrl-1 = <&mmc1_uhs_cfg>;
> +	bus-width = <4>;
> +	cd-gpios = <&gpio K1_GPIO(80) GPIO_ACTIVE_HIGH>;
> +	cd-inverted;
> +	no-mmc;
> +	no-sdio;
> +	disable-wp;
> +	cap-sd-highspeed;
> +	vmmc-supply = <&buck4>;
> +	vqmmc-supply = <&aldo1>;
> +	sd-uhs-sdr25;
> +	sd-uhs-sdr50;
> +	sd-uhs-sdr104;
> +	status = "okay";
> +};
> 
> -- 
> 2.54.0
> 

-- 
Yixun Lan (dlan)