[PATCH v2 4/6] riscv: dts: spacemit: k1-musepi-pro: enable USB 3 ports

[Andre Heider]

Enable the DWC3 USB 3.0 controller, its associated combo_phy (USB 3 PHY)
and usbphy2 (USB 2 PHY) on the MusePi Pro board.

The board uses a VLI VL817 hub, providing four ports.

Signed-off-by: Andre Heider <a.heider at gmail.com>
---
 .../riscv/boot/dts/spacemit/k1-musepi-pro.dts | 54 +++++++++++++++++++
 1 file changed, 54 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts b/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
index 7ebace0e46edb..9c90c2817ecb7 100644
--- a/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
+++ b/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
@@ -54,6 +54,28 @@ reg_vcc_4v0: regulator-vcc-40v {
 		regulator-always-on;
 		vin-supply = <&reg_usb_vbus>;
 	};
+
+	reg_5v_vbus: regulator-5v-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "5V_VBUS";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&reg_usb_vbus>;
+		gpio = <&gpio K1_GPIO(79) GPIO_ACTIVE_HIGH>; /* USB3_PWREN */
+		enable-active-high;
+	};
+
+	reg_vcc5v_hub: regulator-vcc5v-hub {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC5V0_HUB";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&reg_usb_vbus>;
+		gpio = <&gpio K1_GPIO(127) GPIO_ACTIVE_HIGH>; /* HUB_PWREN */
+		enable-active-high;
+	};
 };
 
 &emmc {
@@ -66,6 +88,10 @@ &emmc {
 	status = "okay";
 };
 
+&combo_phy {
+	status = "okay";
+};
+
 &eth0 {
 	phy-handle = <&rgmii0>;
 	phy-mode = "rgmii-id";
@@ -295,3 +321,31 @@ &uart0 {
 	pinctrl-names = "default";
 	status = "okay";
 };
+
+&usbphy2 {
+	status = "okay";
+};
+
+&usb_dwc3 {
+	dr_mode = "host";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	vbus-supply = <&reg_5v_vbus>;
+	status = "okay";
+
+	hub_2_0: hub at 1 {
+		compatible = "usb2109,2817";
+		reg = <0x1>;
+		vdd-supply = <&reg_vcc5v_hub>;
+		peer-hub = <&hub_3_0>;
+		reset-gpios = <&gpio K1_GPIO(123) GPIO_ACTIVE_LOW>; /* HUB_RST */
+	};
+
+	hub_3_0: hub at 2 {
+		compatible = "usb2109,817";
+		reg = <0x2>;
+		vdd-supply = <&reg_vcc5v_hub>;
+		peer-hub = <&hub_2_0>;
+		reset-gpios = <&gpio K1_GPIO(123) GPIO_ACTIVE_LOW>; /* HUB_RST */
+	};
+};
-- 
2.53.0