[PATCH 4/4] riscv: dts: spacemit: enable SPI0 on K3 CoM260-IFX

[Zhengyu He]

SPI0 is the first enabled PDMA consumer on CoM260-IFX, so enable the
PDMA controller together with SPI0.

The board exposes SPI0 on its 40-pin header:

  pin 19: MOSI
  pin 21: MISO
  pin 23: SCLK
  pin 24: CS0

Define the pinctrl state used by this header wiring, and describe the SPI
NOR on chip select 0 for the current validation setup.

(This was tested using a Winbond W25Q64JV SPI NOR chip.)

Signed-off-by: Cody Kang <cody.kang.hk at outlook.com>
Signed-off-by: Zhengyu He <hezhy472013 at gmail.com>
---
 arch/riscv/boot/dts/spacemit/k3-com260-ifx.dts | 13 ++++++++++++-
 arch/riscv/boot/dts/spacemit/k3-pinctrl.dtsi   | 21 +++++++++++++++++++++
 2 files changed, 33 insertions(+), 1 deletion(-)

diff --git a/arch/riscv/boot/dts/spacemit/k3-com260-ifx.dts b/arch/riscv/boot/dts/spacemit/k3-com260-ifx.dts
index 238bb03d0e9e..01a7135df864 100644
--- a/arch/riscv/boot/dts/spacemit/k3-com260-ifx.dts
+++ b/arch/riscv/boot/dts/spacemit/k3-com260-ifx.dts
@@ -11,11 +11,22 @@ / {
 	compatible = "spacemit,k3-com260-ifx", "spacemit,k3-com260", "spacemit,k3";
 
 	aliases {
-		serial0 = &uart0;
 		ethernet0 = &eth1;
+		serial0 = &uart0;
+		spi0 = &spi0;
 	};
 
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
 };
+
+&pdma {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ssp0_2_cfg>;
+	status = "okay";
+};
diff --git a/arch/riscv/boot/dts/spacemit/k3-pinctrl.dtsi b/arch/riscv/boot/dts/spacemit/k3-pinctrl.dtsi
index 3ee1471f3798..9b7617f3846c 100644
--- a/arch/riscv/boot/dts/spacemit/k3-pinctrl.dtsi
+++ b/arch/riscv/boot/dts/spacemit/k3-pinctrl.dtsi
@@ -679,6 +679,27 @@ pwm19-2-pins {
 		};
 	};
 
+	/omit-if-no-ref/
+	ssp0_2_cfg: ssp0-2-cfg {
+		ssp0-0-pins {
+			pinmux = <K3_PADCONF(104, 1)>,  /* ssp0 tx */
+				 <K3_PADCONF(105, 1)>,  /* ssp0 rx */
+				 <K3_PADCONF(106, 1)>;  /* ssp0 clk */
+
+			bias-disable;
+			drive-strength = <25>;
+			power-source = <1800>;
+		};
+
+		ssp0-1-pins {
+			pinmux = <K3_PADCONF(107, 1)>;  /* ssp0 frm */
+
+			bias-pull-up = <0>;
+			drive-strength = <25>;
+			power-source = <1800>;
+		};
+	};
+
 	/omit-if-no-ref/
 	uart0_0_cfg: uart0-0-cfg {
 		uart0-0-pins {

-- 
2.53.0