[PATCH v2 3/5] riscv: dts: thead: lpi4a: sort nodes

[Icenowy Zheng]

Although "D", "H" and "I" are earlier in the alphabet than "P", the DPU,
HDMI and I2C1 nodes were added after PADCTRL nodes in the Lichee Pi 4A
device tree; in addition the PADCTRL1 node is placed before the
PADCTRL0 one.

Sort the nodes in this device tree.

Signed-off-by: Icenowy Zheng <zhengxingda at iscas.ac.cn>
---
 .../boot/dts/thead/th1520-lichee-pi-4a.dts    | 72 +++++++++----------
 1 file changed, 36 insertions(+), 36 deletions(-)

diff --git a/arch/riscv/boot/dts/thead/th1520-lichee-pi-4a.dts b/arch/riscv/boot/dts/thead/th1520-lichee-pi-4a.dts
index af6f25ebbf607..74b120c6b063a 100644
--- a/arch/riscv/boot/dts/thead/th1520-lichee-pi-4a.dts
+++ b/arch/riscv/boot/dts/thead/th1520-lichee-pi-4a.dts
@@ -103,17 +103,31 @@ fan: pwm-fan {
 
 };
 
-&padctrl1_apsys {
-	i2c1_pins: i2c1-0 {
-		i2c-pins {
-			pins = "I2C1_SCL", "I2C1_SDA";
-			function = "i2c";
-			bias-pull-up = <2100>;
-			drive-strength = <7>;
-			input-enable;
-			input-schmitt-enable;
-			slew-rate = <0>;
-		};
+&dpu {
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out_port {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	status = "okay";
+
+	ioexp2: gpio at 18 {
+		compatible = "nxp,pca9557";
+		reg = <0x18>;
+		gpio-controller;
+		#gpio-cells = <2>;
 	};
 };
 
@@ -153,17 +167,17 @@ rx-pins {
 	};
 };
 
-&i2c1 {
-	clock-frequency = <400000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins>;
-	status = "okay";
-
-	ioexp2: gpio at 18 {
-		compatible = "nxp,pca9557";
-		reg = <0x18>;
-		gpio-controller;
-		#gpio-cells = <2>;
+&padctrl1_apsys {
+	i2c1_pins: i2c1-0 {
+		i2c-pins {
+			pins = "I2C1_SCL", "I2C1_SDA";
+			function = "i2c";
+			bias-pull-up = <2100>;
+			drive-strength = <7>;
+			input-enable;
+			input-schmitt-enable;
+			slew-rate = <0>;
+		};
 	};
 };
 
@@ -179,20 +193,6 @@ &sdio1 {
 	status = "okay";
 };
 
-&dpu {
-	status = "okay";
-};
-
-&hdmi {
-	status = "okay";
-};
-
-&hdmi_out_port {
-	hdmi_out_con: endpoint {
-		remote-endpoint = <&hdmi_con_in>;
-	};
-};
-
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins>;
-- 
2.52.0